单选题A client has tried to update the firmware of an Ethernet adapter on a p5 590, however it repeatedly fails. What is the most likely cause of this problem?（）A The adapter must be taken offline prior to the firmware updateB The adapter must be assigned to

题目
单选题
A client has tried to update the firmware of an Ethernet adapter on a p5 590, however it repeatedly fails. What is the most likely cause of this problem?（）
A

The adapter must be taken offline prior to the firmware update

B

The adapter must be assigned to the service partition prior to the firmware update

C

The system has not been rebooted since the adapter was added to the Logical Partition

D

The adapter must be dynamically removed from the Logical Partition prior to the firmware update

相似考题

1.An administrator has a malfunctioning uninterruptible power supply (UPS). Which of the following is the MOST likely cause of the problem?()A. Battery needs to be replacedB. Light switch is turned offC. Smart cable is disconnectedD. UPS needs a firmware update

2.Which of the following is the MOST likely cause of a low wireless signal after an internal wireless adapter on a laptop was replaced?（）A、The wireless card must be calibrated to the laptop.B、The correct preshared encryption key must be installed to boost the signal.C、The MAC address of the new wireless card will have to be added to the WAP to get the full signal.D、The antenna wires for the wireless card were not attached.

3.An administrator has a malfunctioning uninterruptible power supply (UPS). Which of the following is the MOST likely cause of the problem?（）A、Battery needs to be replacedB、Light switch is turned offC、Smart cable is disconnectedD、UPS needs a firmware update

4. A client is experiencing issues after cloning an LPAR using alt_disk_install. DLPAR functions are not available for the new LPAR. Also, there is a lot of network traffic to the HMC. What is the most probable cause of this problem?（）A、DLPAR functions are not available for cloned partitionsB、The new partition has the same node number as the original LPARC、Additional filesets need to be reinstalled after the alt_disk_install cloningD、The speed and duplex settings on the Ethernet adapter on the new LPAR is misconfigured

参考答案和解析
正确答案： A
解析： 暂无解析
更多“单选题A client has tried to update the firmware of an Ethernet adapter on a p5 590, however it repeatedly fails. What is the most likely cause of this problem?（）A The adapter must be taken offline prior to the firmware updateB The adapter must be assigned to”相关问题

  • 第1题：

    A client has tried to update the firmware of an Ethernet adapter on a p5 590, however it repeatedly fails. What is the most likely cause of this problem?（）

    • A、The adapter must be taken offline prior to the firmware update
    • B、The adapter must be assigned to the service partition prior to the firmware update
    • C、The system has not been rebooted since the adapter was added to the Logical Partition
    • D、The adapter must be dynamically removed from the Logical Partition prior to the firmware update

    正确答案:A

  • 第2题：

    When configuring a dual port gigabit Integrated Virtual Ethernet adapter (IVE), what value must be assigned to Multiple Core Scaling (MCS) to enable 8 logical ports in total? （）

    • A、2
    • B、4
    • C、8
    • D、16

    正确答案:A

  • 第3题：

    An administrator issued a command to update the firmware of an Ethernet adapter on a partitioned system， but received an error. What is the most likely cause of the problem？（）

    • A、The adapter must be taken offline prior to the firmware update.
    • B、The system has not been rebooted since the adapter was added to the LPAR.
    • C、The adapter must be assigned to the service partition prior to updating the firmware.
    • D、The adapter must be dynamically removed from the LPAR prior to updating the firmware.

    正确答案:A

  • 第4题：

    Company.com has a VIO server with a configured virtual Ethernet adapter and a physical Ethernet adapter with an IP address on their local public network. They want to re-configure the physical Ethernet adapter as Shared Ethernet Adapter. When the mkvdev command is run， the following method error is returned： /usr/lib/methods/cfgsea . Which of the following will most likely resolve the problem？（）

    • A、Run cfgdev on the VIO server and re-run the mkvdev command.
    • B、Run chdev -a sea_enable=yes on the physical Ethernet adapter.
    • C、Remove and re-add the virtual Ethernet adapter.
    • D、Remove the IP address from the physical adapter and re-run the mkvdev command.

    正确答案:D

  • 第5题：

    An administrator is trying to connect to an RSA-II adapter using the default IP address found in the installation manual of 192.168.70.125.  The Web browser returns a "page cannot be displayed" message， and a ping returns a "request timed out" message.  Which of the following is the most likely cause of the problem？（）

    • A、The RSA II adapter has obtained a DHCP assigned address.
    • B、The RSA II adapter requires independent power to function.
    • C、The Class C IP address space is not being bridged on the network.
    • D、The RSA II adapter needs to be configured using a serial connection.

    正确答案:A

  • 第6题：

    单选题
    A client has an existing Logical Partition (LPAR) on a p650 running AIX 5.2 and will be porting this LPAR to a p5 590. A mksysb has been run to tape, and a compatible tape drive is available and allocated to the target LPAR on the p5 590. What additional resource needs to be available on the p5 590?（）
    A

    A CD or DVD with installation media

    B

    An internal SCSI adapter in the target LPAR

    C

    An Ethernet adapter for access to an FTP server

    D

    Advanced Power Virtualization feature of the p5 590


    正确答案： B
    解析： 暂无解析

  • 第7题：

    单选题
    A client is experiencing issues after cloning an LPAR using alt_disk_install. DLPAR functions are not available for the new LPAR. Also, there is a lot of network traffic to the HMC. What is the most probable cause of this problem?（）
    A

    DLPAR functions are not available for cloned partitions

    B

    The new partition has the same node number as the original LPAR

    C

    Additional filesets need to be reinstalled after the alt_disk_install cloning

    D

    The speed and duplex settings on the Ethernet adapter on the new LPAR is misconfigured


    正确答案： D
    解析： 暂无解析

  • 第8题：

    单选题
    Refer to the exhibit. A Cisco Aironet Wireless LAN Client Adapter has been installed and configured through the ADU on the PC. The Aironet System Tray Utility （ASTU） has been enabled during the installation and the icon appears in the system tray area in the lower right of the desktop. What is thesignificance of the icon？（）
    A

    It indicates that the radio of the client adapter is disabled

    B

    It indicates that the client adapter is not associated to an access point or another client

    C

    It indicates that the client adapter is associated to an access point or another client， but the user is not EAP authenticated

    D

    It indicates that the client adapter is associated to an access point or another client， that the user is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is excellent or good

    E

    It indicates that the client adapter is associated to an access point or another client， that the user is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is fair

    F

    It indicates that the client adapter is associated to an access point or another client， that the user is authenticated if the client adapter is configured for EAP authentication， and that the signal strength is poor


    正确答案： F
    解析： 暂无解析

  • 第9题：

    单选题
    Refer to the exhibit. A Cisco Aironet Wireless LAN Client Adapter has been installed and configured  through the ADU on the PC. The Aironet System Tray Utility （ASTU） has been enabled during the  installation and the icon appears in the system tray area in the lower right of the desktop. What is the  significance of the icon？（）
    A

     It indicates that the radio of the client adapter is disabled.

    B

     It indicates that the client adapter is not associated to an access point or another client. 

    C

     It indicates that the client adapter is associated to an access point or another client， but the user is not  EAP authenticated.

    D

     It indicates that the client adapter is associated to an access point or another client， that the user is  authenticated if the client adapter is configured for EAP authentication， and that the signal strength is  excellent or good.

    E

     It indicates that the client adapter is associated to an access point or another client， that the user is  authenticated if the client adapter is configured for EAP authentication， and that the signal strength is fair.

    F

     It indicates that the client adapter is associated to an access point or another client， that the user is  authenticated if the client adapter is configured for EAP authentication， and that the signal strength is poor.


    正确答案： F
    解析： 暂无解析

  • 第10题：

    单选题
    An administrator issued a command to update thefirmware of an Ethernet adapter on a partitioned system, but received an error. What is the most likely cause of the problem?（）
    A

    The adapter must be taken offline prior to the firmware update.

    B

    The system has not been rebooted since the adapter was added to the LPAR.

    C

    The adapter must be assigned to the service partition prior to updating the firmware.

    D

    The adapter must be dynamically removed from the LPAR prior to updating thefirmware.


    正确答案： D
    解析： 暂无解析

  • 第11题：

    单选题
    An administrator issued a command to update the firmware of an Ethernet adapter on a partitioned system， but received an error. What is the most likely cause of the problem？（）
    A

    The adapter must be taken offline prior to the firmware update.

    B

    The system has not been rebooted since the adapter was added to the LPAR.

    C

    The adapter must be assigned to the service partition prior to updating the firmware.

    D

    The adapter must be dynamically removed from the LPAR prior to updating the firmware.


    正确答案： D
    解析： 暂无解析

  • 第12题：

    单选题
    A client tried to upgrade the system firmware on a p5 590, but it failed. What is the minimum requirement to update the system firmware from the HMC if inventory scout is already installed?（）
    A

    A public internet connection

    B

    All of the Logical Partitions need to be active

    C

    One partition must be configured with Service Authority

    D

    A local Repository must be configured prior to the update


    正确答案： A
    解析： 暂无解析

  • 第13题：

    A machine must have the most direct access possible to two different networks.  However， it cannot act as a router between the networks.  Which of the following arrangements is most appropriate to facilitate the machine’s accessibility？（）

    • A、ipforwarding turned on and two adapters
    • B、One adapter， with a route to a default gateway
    • C、An adapter in each network， and ipforwarding off
    • D、An adapter in each network， with a route only to the default gateway

    正确答案:C

  • 第14题：

    An administrator issued a command to update thefirmware of an Ethernet adapter on a partitioned system, but received an error. What is the most likely cause of the problem?（）

    • A、The adapter must be taken offline prior to the firmware update.
    • B、The system has not been rebooted since the adapter was added to the LPAR.
    • C、The adapter must be assigned to the service partition prior to updating the firmware.
    • D、The adapter must be dynamically removed from the LPAR prior to updating thefirmware.

    正确答案:A

  • 第15题：

    A client has an existing Logical Partition (LPAR) on a p650 running AIX 5.2 and will be porting this LPAR to a p5 590. A mksysb has been run to tape, and a compatible tape drive is available and allocated to the target LPAR on the p5 590. What additional resource needs to be available on the p5 590?（）

    • A、A CD or DVD with installation media
    • B、An internal SCSI adapter in the target LPAR
    • C、An Ethernet adapter for access to an FTP server
    • D、Advanced Power Virtualization feature of the p5 590

    正确答案:A

  • 第16题：

    A client tried to upgrade the system firmware on a p5 590, but it failed. What is the minimum requirement to update the system firmware from the HMC if inventory scout is already installed?（）

    • A、A public internet connection
    • B、All of the Logical Partitions need to be active
    • C、One partition must be configured with Service Authority
    • D、A local Repository must be configured prior to the update

    正确答案:C

  • 第17题：

    单选题
    Company.com has a VIO server with a configured virtual Ethernet adapter and a physical Ethernet adapter with an IP address on their local public network. They want to re-configure the physical Ethernet adapter as Shared Ethernet Adapter. When the mkvdev command is run， the following method error is returned： /usr/lib/methods/cfgsea . Which of the following will most likely resolve the problem？（）
    A

    Run cfgdev on the VIO server and re-run the mkvdev command.

    B

    Run chdev -a sea_enable=yes on the physical Ethernet adapter.

    C

    Remove and re-add the virtual Ethernet adapter.

    D

    Remove the IP address from the physical adapter and re-run the mkvdev command.


    正确答案： D
    解析： 暂无解析

  • 第18题：

    单选题
    An administrator has a malfunctioning uninterruptible power supply (UPS). Which of the following is the MOST likely cause of the problem?（）
    A

    Battery needs to be replaced

    B

    Light switch is turned off

    C

    Smart cable is disconnected

    D

    UPS needs a firmware update


    正确答案： D
    解析： 暂无解析

  • 第19题：

    单选题
    An administrator is trying to connect to an RSA-II adapter using the default IP address found in the installation manual of 192.168.70.125.  The Web browser returns a "page cannot be displayed" message， and a ping returns a "request timed out" message.  Which of the following is the most likely cause of the problem？（）
    A

    The RSA II adapter has obtained a DHCP assigned address.

    B

    The RSA II adapter requires independent power to function.

    C

    The Class C IP address space is not being bridged on the network.

    D

    The RSA II adapter needs to be configured using a serial connection.


    正确答案： D
    解析： 暂无解析

  • 第20题：

    单选题
    When configuring a dual port gigabit Integrated Virtual Ethernet adapter (IVE), what value must be assigned to Multiple Core Scaling (MCS) to enable 8 logical ports in total? （）
    A

    2

    B

    4

    C

    8

    D

    16


    正确答案： A
    解析： 暂无解析

  • 第21题：

    单选题
    What is the implication of using Deferred versus Concurrent firmware updates？（）
    A

    Deferred firmware updates require a reboot to be applied， while concurrent updates do not.

    B

    Deferred firmware updates require a full power IPL to be applied while concurrent updates do not.

    C

    Concurrent firmware updates require all LPARs to be quiesced and shutdown prior to initiating the update， while deferred updates do not.

    D

    Concurrent firmware updates can be applied to multiple managed systems in parallel， while deferred updates must be applied sequentially.


    正确答案： B
    解析： 暂无解析

  • 第22题：

    单选题
    A machine must have the most direct access possible to two different networks.  However， it cannot act as a router between the networks.  Which of the following arrangements is most appropriate to facilitate the machine’s accessibility？（）
    A

    ipforwarding turned on and two adapters

    B

    One adapter， with a route to a default gateway

    C

    An adapter in each network， and ipforwarding off

    D

    An adapter in each network， with a route only to the default gateway


    正确答案： C
    解析： 暂无解析

  • 第23题：

    单选题
    A client has tried to update the firmware of an Ethernet adapter on a p5 590, however it repeatedly fails. What is the most likely cause of this problem?（）
    A

    The adapter must be taken offline prior to the firmware update

    B

    The adapter must be assigned to the service partition prior to the firmware update

    C

    The system has not been rebooted since the adapter was added to the Logical Partition

    D

    The adapter must be dynamically removed from the Logical Partition prior to the firmware update


    正确答案： B
    解析： 暂无解析

  • 第24题：

    单选题
    An administrator has a malfunctioning uninterruptible power supply （UPS）. Which of the following is the MOST likely cause of the problem？（）
    A

     Battery needs to be replaced

    B

     Light switch is turned off

    C

     Smart cable is disconnected

    D

     UPS needs a firmware update


    正确答案： B
    解析： 暂无解析

相关内容