A client is experiencing issues after cloning an LPAR using alt_disk_install. DLPAR functions are not available for the new LPAR. Also, there is a lot of network traffic to the HMC. What is the most probable cause of this problem?（）A、DLPAR functions are 

题目

A client is experiencing issues after cloning an LPAR using alt_disk_install. DLPAR functions are not available for the new LPAR. Also, there is a lot of network traffic to the HMC. What is the most probable cause of this problem?（）

  • A、DLPAR functions are not available for cloned partitions
  • B、The new partition has the same node number as the original LPAR
  • C、Additional filesets need to be reinstalled after the alt_disk_install cloning
  • D、The speed and duplex settings on the Ethernet adapter on the new LPAR is misconfigured
相似考题

1.After connecting a PC to an available port on a switch, you find that the PC can not access any of the resources on the LAN. No other PC's connected to the switch appear to be having any issues. What is the most likely cause for this problem?A．The router lacks a routing table entry for the new hostB．The host switch port is assigned to the incorrect VLANC．The host MAC address is incorrectly configuredD．A STP instance for the new host has not been initializedE．The switch does not have the MAC address hard coded in the CAM table.

2.You are trying to bring up a new Testking location onto your existing frame relay network. The new location is using an Adtran router and you are having difficulties getting the site to connect via frame to your Cisco HQ router. What is the most likely cause of the problem?（）A. Mismatched LMI types.B. Incompatible encapsulation types.C. Mismatching IP addresses.D. Incorrect DLCI.E. None of the above

3.A Network Engineer is reporting that one of the AIX hosts is generating too much ICMP traffic, which is slowing the network.  Which of the following options is the most probable cause?（）A、A large FTP job is in process. B、A network interface was misconfigured. C、The ping command is being used excessively. D、A bad network interface card and/or network cable is in use. 

4.The system administrator did a new install of AIX on a server about a week ago. The system was not rebooted after the installation. CDE is running on this system as is TCPIP. The system administrator has started configuring the system percompany directives. The power cable was inadvertently disconnected from the wall causing the sever to lose power. Upon reboot, the system appears to hang during log in from the console or from Xterminals. Which of the following is the most probable cause?（）A.It is a hardware problem caused by the power failure.B.There is a network problem, most probably with name resolution.C.Sine the system was never rebooted, devices are marked defined instead of available and need to be activated.D.Some filesets may be marked as broken and need to be reinstalled.

更多“A client is experiencing issues after cloning an LPAR using alt_disk_install. DLPAR functions are not available for the new LPAR. Also, there is a lot of network traffic to the HMC. What is the most probable cause of this problem?（）A、DLPAR functions are n”相关问题

  • 第1题：

    A system administrator is creating four LPARs on a Power 550. The Power 550 has 64GB of memoryinstalled and 32GB activated. The system administrator sets the minimum dedicated memory to 8GB in the profile for each LPAR. After activating three LPARs, he is not able to activate the fourth LPAR. What is the likely cause of the problem?（）

    • A、The Power 550 is licensed for three LPARs only.
    • B、There is not enough memory to meet the minimum dedicated memory requirement for the fourth LPAR. A faulty memory DIMM is detected in the POWER5 550.
    • C、There is not enough memory to meet the minimum dedicated memory requirement for the fourth LPAR. The HMC reserves some memory to perform logical partition tasks.
    • D、There is not enough memory to meet the minimum dedicated memory requirement for the fourth LPAR. The hypervisor reserves some memory to perform logical partition tasks.

    正确答案:D

  • 第2题：

    While you are troubleshooting network performance issues， you notice that a switch is periodically flooding all unicast traffic. Further investigation reveals that periodically the switch is also having spikes in CPU utilization， causing the MAC address table to be flushed and relearned. What is the most likely cause of this issue？（）

    • A、a routing protocol that is flooding updates
    • B、a flapping port that is generating BPDUs with the TCN bit set
    • C、STP is not running on the switch
    • D、a user that is downloading the output of the show-tech command
    • E、a corrupted switch CAM table

    正确答案:B

  • 第3题：

    A client is having trouble connecting to the Internet. The client is using a static IP address and is able to connect to other devices on the network via IP address only. Which of the following is MOST likely the problem?（）

    • A、IMAP
    • B、DHCP
    • C、DNS
    • D、NAT

    正确答案:C

  • 第4题：

    Companycom is installing a p5 595 with AIX 5.3. The DLPAR option for the resources cannot be selected on the HMC menus. However, the daemons are running on both the HMC and LPARs. Which of the following is a prerequisite for DLPAR functionality?（）

    • A、The resources must be unallocated in an LPAR
    • B、The microcode on the pSeries must be current
    • C、All network adapters on the LPAR must be defined
    • D、Network connectivity and name resolution capability between HMC and LPARs

    正确答案:D

  • 第5题：

    An adapter state does not show available after a reboot.  Which of the following is the most probable cause？（）

    • A、DNS is not working properly
    • B、Ping is not working properly
    • C、The cables are disconnected
    • D、The device driver did not load properly

    正确答案:D

  • 第6题：

    The nfsstat -c command shows zero badxid， but retrans and timeouts are sizeable， what is the most probable cause of the problem？（）

    • A、 Too many nfsd’s running
    • B、 Client and server with different buffer sizes
    • C、 Bridges， routers or gateways are receiving too many fragmentated packets
    • D、 Too few nfsd’s running

    正确答案:B

  • 第7题：

    SuSe Linux Enterprise Server (SLES) has been installed on an LPAR on a p5 570, but the client is having problems directly after installation with slow network performance. What is the most probable cause?（）

    • A、SLES does not perform well with DHCP
    • B、SLES was installed with the default host name of Linux
    • C、Virtual Network Resources are being used, which is not supported in a SLES environment
    • D、The SLES instance was installed in 32-bit mode, where 64-bit should have been selected

    正确答案:B

  • 第8题：

    单选题
    The system administrator did a new install of AIX on a server about a week ago. The system was not rebooted after the installation. CDE is running on this system as is TCPIP. The system administrator has started configuring the system percompany directives. The power cable was inadvertently disconnected from the wall causing the sever to lose power. Upon reboot, the system appears to hang during log in from the console or from Xterminals. Which of the following is the most probable cause?（）
    A

    It is a hardware problem caused by the power failure.

    B

    There is a network problem, most probably with name resolution.

    C

    Sine the system was never rebooted, devices are marked defined instead of available and need to be activated.

    D

    Some filesets may be marked as broken and need to be reinstalled.


    正确答案： C
    解析： 暂无解析

  • 第9题：

    单选题
    System configurations on the HMC have been backed up correctly. After a restore, the partitions are defined with different characteristics than the running systems. What is the most probable cause of this problem?（）
    A

    The LPAR Configuration backup is corrupt

    B

    The LPAR Configuration has been altered using DLPAR

    C

    The LPAR Configuration backup was performed on a different HMC

    D

    The LPAR Configuration has been altered through the Advanced System Management Interface （ASMI） on the server after the backup was performed


    正确答案： C
    解析： 暂无解析

  • 第10题：

    单选题
    The nfsstat -c command shows zero badxid， but retrans and timeouts are sizeable， what is the most probable cause of the problem？（）
    A

     Too many nfsd’s running

    B

     Client and server with different buffer sizes

    C

     Bridges， routers or gateways are receiving too many fragmentated packets

    D

     Too few nfsd’s running


    正确答案： D
    解析： 暂无解析

  • 第11题：

    单选题
    Companycom is migrating from a p690 to a p5 595 utilizing APV Virtual IO features. They have created their profiles for their two Virtual IO Servers. The first Virtual IO Server is installed and running. When trying to DLPAR the DVD/ROM the task fails on the HMC. What is the probable cause?（）
    A

    APV key is not registered

    B

    Networking and DNS are not configured

    C

    /etc/hosts table on HMC is not configured

    D

    Virtual IO Server dose not support DLPAR


    正确答案： D
    解析： 暂无解析

  • 第12题：

    单选题
    After using the alt_disk_install command to clone a system image to another disk, the system administrator noticed a large number of defined devices not allocated to the LPAR. Which of the following is the most likely cause of this situation?（）
    A

    The cfgmgr command was not run to reconfigure the devices

    B

    The machine was not booted into SMS MultiBoot mode after configuration

    C

    The machine was not in full system partition mode when the volume was created

    D

    The alt_disk_install command was not run with the -O option to remove references in the ODM


    正确答案： C
    解析： 暂无解析

  • 第13题：

    Companycom has just purchased a p5 570 with AIX 5.3. The customer would like to add a training LPAR to the system, but no processors are available. All of the partitions are using dedicated resources. The test LPAR is using one processor and has a 90% CPU idle rate. What can be done to setup this training LPAR quickly without disabling their current environment?（）

    • A、Use AIX 5.3 which supports micro-partitioning for both the test and training LPARS
    • B、Use DLPAR to move resources from the test LPAR to training when training is active
    • C、Install Partition Load Manager to share resources between the test and training environments
    • D、Install Advanced Power Virtualization and then use micro-partitioning for both the test and  training LPARs

    正确答案:D

  • 第14题：

    A customer has installed a new computer on their network. They can print to the printer but the option for duplex printing is not available. All other computers have the option. Which of the following is the cause of the problem？（）

    • A、The new computer is printing to the wrong IP address.
    • B、The new computer is using the wrong protocol.
    • C、The driver port is not setup correctly.
    • D、The option has not been selected on the driver.

    正确答案:D

  • 第15题：

    Companycom is migrating from a p690 to a p5 595 utilizing APV Virtual IO features. They have created their profiles for their two Virtual IO Servers. The first Virtual IO Server is installed and running. When trying to DLPAR the DVD/ROM the task fails on the HMC. What is the probable cause?（）

    • A、APV key is not registered
    • B、Networking and DNS are not configured
    • C、/etc/hosts table on HMC is not configured
    • D、Virtual IO Server dose not support DLPAR

    正确答案:B

  • 第16题：

    A customer has shut down an LPAR after using DLPAR to add or remove processor and memory resources. When the partition is reactivated, the desired changes are missing. What action, or sequence of actions, will immediately and permanently solve this problem?（）

    • A、Add or remove the resources in the profile, click 'apply', then 'save'.
    • B、Add or remove the resources using DLPAR and change the partition profile.
    • C、Add or remove the resources using DLPAR, then shutdown and reactivate the LPAR.
    • D、Add or remove the resources in the system profile and reboot the managed system.

    正确答案:B

  • 第17题：

    A technical consultant needs to deploy a Microsoft Windows 2003 server image from a single x336 to five new x336 servers using Remote Deployment Manager （RDM）.  After installing and configuring RDM and loading the installation image， the consultant wants to deploy the first server.  After the new x336 is booted， it is unable to connect to the RDM server.  Which of the following is the most likely cause of the problem？（）

    • A、The new server is not PXE-enabled.
    • B、The RDM agent is not configured on the RDM server.
    • C、The IBM Director agent is not installed on the new server.
    • D、A DHCP server is not installed or configured the network.

    正确答案:D

  • 第18题：

    System configurations on the HMC have been backed up correctly. After a restore, the partitions are defined with different characteristics than the running systems. What is the most probable cause of this problem?（）

    • A、The LPAR Configuration backup is corrupt
    • B、The LPAR Configuration has been altered using DLPAR
    • C、The LPAR Configuration backup was performed on a different HMC
    • D、The LPAR Configuration has been altered through the Advanced System Management Interface （ASMI） on the server after the backup was performed

    正确答案:B

  • 第19题：

    单选题
    A client is experiencing issues after cloning an LPAR using alt_disk_install. DLPAR functions are not available for the new LPAR. Also, there is a lot of network traffic to the HMC. What is the most probable cause of this problem?（）
    A

    DLPAR functions are not available for cloned partitions

    B

    The new partition has the same node number as the original LPAR

    C

    Additional filesets need to be reinstalled after the alt_disk_install cloning

    D

    The speed and duplex settings on the Ethernet adapter on the new LPAR is misconfigured


    正确答案： D
    解析： 暂无解析

  • 第20题：

    单选题
    An adapter state does not show available after a reboot.  Which of the following is the most probable cause？（）
    A

    DNS is not working properly

    B

    Ping is not working properly

    C

    The cables are disconnected

    D

    The device driver did not load properly


    正确答案： D
    解析： 暂无解析

  • 第21题：

    单选题
    Companycom is installing a p5 595 with AIX 5.3. The DLPAR option for the resources cannot be selected on the HMC menus. However, the daemons are running on both the HMC and LPARs. Which of the following is a prerequisite for DLPAR functionality?（）
    A

    The resources must be unallocated in an LPAR

    B

    The microcode on the pSeries must be current

    C

    All network adapters on the LPAR must be defined

    D

    Network connectivity and name resolution capability between HMC and LPARs


    正确答案： D
    解析： 暂无解析

  • 第22题：

    单选题
    A client is experiencing issues after cloning an LPAR using alt_disk_install. DLPAR functions are not available for the new LPAR. Also, there is a lot of network traffic to the HMC. What is the most probable cause of this problem?（）
    A

    DLPAR functions are not available for cloned partitions

    B

    The new partition has the same node number as the original LPAR

    C

    Additional filesets need to be reinstalled after the alt_disk_install cloning

    D

    The speed and duplex settings on the Ethernet adapter on the new LPAR is misconfigured


    正确答案： C
    解析： 暂无解析

  • 第23题：

    填空题
    What was the probable cause of the fire?Most likely a burning ____.

    正确答案： cigarette
    解析：
    因果关系题。由听力原文中“When we asked the fire chief how the fire started, he answered that most likely a burning cigarette caused it”可以推断，救火队长认为火灾是由点燃的香烟引起的，所以填cigarette。
    【录音原文】
    　　Now back to the news. An early morning fire damaged the historic Geller House today. It destroyed the third floor of the building, but the firefighters saved the first and second floors. There were only a few elderly people living in the building at that time. And they were carried out to safety.
    　　The Geller House was built in 1718 and it was used as a hotel for over 150 years. George Washington stayed there in 1782. Five years ago, it was made into a building for the elderly.
    　　Several fire departments were called to the scene. When we asked the fire chief how the fire started, he answered that most likely a burning cigarette caused it. He promised to make a further investigation into the cause.
    Q11: At what time of day did the fire start?
    Q12: Which floor of the building did the fire destroy?
    Q13: Who lived in the building at the time of the fire?
    Q14: When was the Geller House built?
    Q15: What was the probable cause of the fire?

相关内容