OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterAping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request

A. After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interface

B. When you use the passive - interface command with RIPv2, multicasts are sent out the specified interface

C. After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interface

D. When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interface

E. After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interface

F. When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface

Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）

A. The no auto - summary command needs to be added under router eigrp 1

B. The subnets keyword was not included in the redistribute command under router ospf 1

C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router A

D. The default - information originate command needs to be added under router ospf 1

E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF

You have implemented mutua l route redistribution between OSPF and EIGRP on a border router. When checking the routing table on one of the EIGRP routers within the EIGRP routing domain, you are seeing some, but not all of the expected routes.What should you verify to troubleshoot this problem?（）

A. The border router is using a proper seed metric for OSPF

B. The border router is using a proper seed metric for EIGRP

C. The administrative distance is set for OSPF and EIGRP

D. The missing OSPF routes are present in the routing table of the border router

E. The subnet keyword on the border router in the redistribute OSPF command

A. router ospf ipv6 process - id

B. ipv6 ospf process - id

C. router ospf process - id

D. ipv6 router ospf process - id

You try to add a new router into the established Testking OSPF network. The networks attached to the new router do not appear in the routing tables of the other OSPF routers.The new router was configured for OSPF in the following way:Router(config) router ospf 99Router(config-if) network 10.0.0.0 255.0.0.0 area 0Based on this information, what is the most likely problem?（）

A. The process id is configured improperly.

B. The OSPF area is configured improperly.

C. The network wildcard mask is configured improperly.

D. The network number is configured improperly.

E. The AS is configured improperly.

F. The network subnet mask is configured improperly.

G. All of the above are likely problems.

Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）

A. Add the area 1 stub command on routers R1.

B. Add the always keyword to the default - information originate configuration command on router R2.

C. Remov e the default information originate configuration command from router R2 and place it on router R1.

D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.

You have implemented mutual route redistribution between OSPF and EIGRP on a border router. When checking the routing table on one o f the OSPF routers within the OSPF routing domain, you are seeing some, but not all of the expected routes.Which two things should you verify to troubleshoot this problem?（）

A. The border router is using a proper seed metric for OSPF

B. The border ro uter is using a proper seed metric for EIGRP

C. The administrative distance is set for OSPF and EIGRP

D. The missing EIGRP routes are present in the routing table of the border router

E. The subnet keyword on the border router in the redistribute EIG RP command

Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）

A. All OSPF implementations must have at le ast one interface in area 0.

B. You are attempting to run in the broadcast mode over an NBMA interface.

C. Both routers are configured to function as a BDR; therefore, there is no DR router.

D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.

E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.

You are troubleshooting a WAN connection for TestKing, and on the router you execute the, "debug ppp authentication" command, and view the following output:What kind of handshake was used for the PPP authentication?（）

A. one-way

B. two-way

C. three-way

D. No handshakes required during authentication

E. None of the above

A. Router(config-router)# network 192.168.10.0 0.0.0.255 0

B. Router(config-router)# network 192.168.10.0 0.0.0.255 area 0

C. Router(config-router)# network 192.168.10.0 255.255.255.0 area 0

D. Router(config)# router ospf 0

E. Router(config)# router ospf 1