Refer to the exhibit. When running OSPF, What would cause router A not to form an adjacency with router B?()A.The loopback addresses are on different subnetsB.The value of the dead timers on the router are differentC.Route summarization is enabled on both

Refer to the exhibit. OSPF is configured on all routers in the network. Area 5 is configured as an NSSA areA. The RIPv2 routes are redistributed into the OSPF domain on router R5. What two types of LSAs will be originated by router R5?（）

A. type 1 Router LSA

B. type 2 Network LSA

C. type 3 Network Summary LSA

D. type 4 ASBR Summary LSA

E. type 5 AS External LSA

F. type 7 NSSA External LSA

A.show ip ospf

B.show ip ospf interface

C.show ip ospf neighbor

D.show ip ospf database

E.show ip ospf statistics

F.show running - config begin router ospf

Refer to the exhibit. AS 65500 is not advertising the prefix 192.168.12.0/22 to its provider. AS 65500 is running OSPF as its IGP. Whi ch of the following additions to the configuration is most likely to solve the problem?（）

A. RouterA(config)#ip cef

B. RouterA(config)#ip route 192.168.12.0 255.255.255.252 null 0

C. RouterA(config - router)#ebgp multihop 1

D. RouterA(config - router)#re distribute ospf 1

E. RouterA(config - router)#neighbor 192.168.14.253 next - hop - self

F. RouterA(config - router)#neighbor 192.168.14.253 local - as 65500

Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）

A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcast

B. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - point

C. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3

D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253

Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）

A. All OSPF implementations must have at le ast one interface in area 0.

B. You are attempting to run in the broadcast mode over an NBMA interface.

C. Both routers are configured to function as a BDR; therefore, there is no DR router.

D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.

E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.

A. Router RTA is the BDR

B. Router RTA is directly connected to interface 192.168.45.1

C. Neighbor 192.168.45.1 has changed its OSPF priority number

D. Router RTA and neighbor 192.168.45.2 are exchanging OSPF LSAs

Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）

A. Add the area 1 stub command on routers R1.

B. Add the always keyword to the default - information originate configuration command on router R2.

C. Remov e the default information originate configuration command from router R2 and place it on router R1.

D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.

Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）

A. The no auto - summary command needs to be added under router eigrp 1

B. The subnets keyword was not included in the redistribute command under router ospf 1

C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router A

D. The default - information originate command needs to be added under router ospf 1

E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF

Refer to the exhibit. Router C was configured so that it could form an adja cency with three OSPF neighbors, one connected to each of its three physical interfaces. Which statement is correct about router C?（）

A. It is configured and functioning correctly as an OSPF internal router.

B. It is configured and functioning correc tly as an ABR attached to stub area 4.

C. It is configured and functioning correctly as an ASBR attached to external area 4.

D. It is configured and functioning correctly as an ABR attached to totally stubby area 4.

E. It is not configured correctly to function as specified.

Refer to the exhibit. A network administrator wants to reduce the number of OSPF routes advertised from Area 1 into Area 2. As the router configuration specialist, what two things would you do to accomplish this goal?（）

A. Enter the configuration on router B1.

B. Enter the configuration on router B4.

C. On the same router, enter the Summary - address 10.10.1.0 255.255.255.128 subcommand.

D. On the same router, enter the Area 1 range 10.10.1.0 255.255.255.128 subcommand.

E. On the same ro uter, enter the Area 2 range 10.10.1.0 255.255.255.128 subcommand.

A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.

B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.

C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.

D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.

E. The Hello parameters on routers R1 and R2 do not m atch.