The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?()A. The Gallant router has the wrong LMI type configuredB. Inverse ARP is providing the wrong PVC information to the Gallant routerC. The S3 interface of

题目
The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?()

A. The Gallant router has the wrong LMI type configured

B. Inverse ARP is providing the wrong PVC information to the Gallant router

C. The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command

D. The frame-relay map statement in the Attalla router for the PVC to Steele is not correct

E. The IP address on the serial interface of the Attalla router is configured incorrectly

相似考题

1.Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? ()A. frame-relay arpB. frame-relay mapC. frame-relay interface-dlciD. frame-relay lmi-type

2.The Testking Central and Remote offices are configured as shown below:The remote router can be successfully pinged from the central office but the remote users can‘t access the server at the central office.Based on the output above, what do you suspect is the cause of this problem?（）A. The Frame Relay PVC is down.B. The IP addressing on the Central/Remote serial link is incorrect.C. RIP routing information is not being forwarded.D. Frame Relay inverse-ARP is not properly configured.

3.OSPF is configured over a Frame Relay network as shown in the exhibit. All PVCs are active.However, R1 and R3 fail to see all OSPF routes in their routing tables. The show ip ospf neighbor command executed on R2 shows the state of t he neighbors. What should be done to fix the problem? （）A. The ip ospf network broadcast command should be configured on each Frame Relay interfaceB. The ip ospf network non -broadcast command should be configured on each Frame Relay interfaceC. Th e ip ospf priority value on the spoke routers should be set to 0D. The ip ospf priority value on the hub router should be set to 0E. The neighbor command should be configured under the OSPF routing process on all routers

4.In regard to a hub and spoke Frame－Relay data network, what kind of physical network is it classified as?()A. point-to-pointB. broadcast multi-accessC. nonbroadcast multipointD. nonbroadcast multi-accessE. broadcast point-to-multipoint

参考答案和解析
参考答案：D
更多“The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?() ”相关问题

  • 第1题：

    You are a network administrator at TestKing, Inc. and you‘re getting complaintsthat users on the TestKing2 Ethernet network can‘t access the TestKing1 site. Totroubleshoot this, you begin by looking at the Testking1 and Testking2 routerconfigurations as shown below:Based on the above output, what is the underlying cause of this problem?（）

    A. Link state routing protocol is missing.

    B. Incorrectly configured IP addresses

    C. IGRP is incorrectly configured.

    D. Frame relay is not configured.

    E. None of the above


    参考答案：C

  • 第2题：

    The Frame Relay network in the diagram is not functioning properly.What is the cause of the problem?()

    A.The Gallant router has the wrong LMI type configured

    B.Inverse ARP is providing the wrong PVC information to the Gallant router

    C.The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command

    D.The frame-relay map statement in the Attalla router for the PVC to Steele is not correct

    E.The IP address on the serial interface of the Attalla router is configured incorrectly


    参考答案：D

  • 第3题：

    A new frame-relay network is being implemented and inverse ARP does not appear to be operating correctly. Which alternative command can be used to provide connectivity?（）

    • A、frame-relay arp
    • B、frame-relay map
    • C、frame-relay interface-dlci
    • D、frame-relay lmi-type
    • E、frame-relay pvc

    正确答案:B

  • 第4题：

    In order to troubleshoot an issue with the Testking frame relay network, you log into a remote router via a telnet session and issue the command "debug frame-relay lmi". After a long wait, you fail to see any output. What could be the cause of this problem?（）

    • A、The IP addresses are configured incorrectly.
    • B、Frame Relay LMI messages not displayed in real time.
    • C、The administrator must issue the enable frame-relay lmi debug command.
    • D、The administrator must issue the terminal monitor command.
    • E、Debug messages can only be received once through the console port.
    • F、The administrator must issue the show frame-relay lmi vty 0 4 command

    正确答案:D

  • 第5题：

    You are trying to bring up a new Testking location onto your existing frame relay network. The new location is using an Adtran router and you are having difficulties getting the site to connect via frame to your Cisco HQ router. What is the most likely cause of the problem?（）

    • A、Mismatched LMI types.
    • B、Incompatible encapsulation types.
    • C、Mismatching IP addresses.
    • D、Incorrect DLCI.
    • E、None of the above

    正确答案:B

  • 第6题：

    Which three statements about L2TPv3 are true？（）

    • A、L2TPv3 Frame Relay support includes only 32-bit DLCI addressing
    • B、L2TPv3 sessions do not support Frame Relay LMI interworking
    • C、Multipoint DLCI is not supported
    • D、To use DCE or a Network-to-Network Interface on a Frame Relay port， you must configure the frame-relay switching command
    • E、L2TPv3 feature does not support Frame Relay extended addressing

    正确答案:B,D,E

  • 第7题：

    A default Frame Relay WAN is classified as what type of physical network（）。

    • A、point-to-point
    • B、broadcast multi-access
    • C、nonbroadcast multi-access
    • D、nonbroadcast multipoint
    • E、broadcast point-to-multipoint

    正确答案:C

  • 第8题：

    Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? （）

    • A、frame-relay arp
    • B、frame-relay map
    • C、frame-relay interface-dlci
    • D、frame-relay lmi-type

    正确答案:B

  • 第9题：

    单选题
    The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）
    A

    The Gallant router has the wrong LMI type configured

    B

    Inverse ARP is providing the wrong PVC information to the Gallant router

    C

    The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command

    D

    The frame-relay map statement in the Attalla router for the PVC to Steele is not correct

    E

    The IP address on the serial interface of the Attalla router is configured incorrectly


    正确答案： C
    解析： 暂无解析

  • 第10题：

    单选题
    Customer X has a hub-and-spoke Frame Relay network， with a central office and two branch offices （RemoteA and RemoteB）. Each location has only one physical link to the Frame Relay cloud and RemoteB has a router that is not a Cisco router. Since the installation， there is no connectivity between RemoteB and the central office. What is a possible solution to this issue？ （）
    A

     Because Frame Relay IETF encapsulation is only configurable at interface level， you must use IETF encapsulation on all routers.

    B

     This is not a possible scenario. A dedicated Frame Relay link to RemoteB is mandatory at the central office.

    C

     The router at RemoteB must be replaced by a Cisco router.

    D

     Use Frame Relay IETF encapsulation on a per-VC basis on the central office router.

    E

     There is a problem in the Frame Relay cloud， because Cisco routers are compatible with IETF Frame Relay.


    正确答案： D
    解析： 暂无解析

  • 第11题：

    单选题
    What is a Label-Switched Path?（）
    A

    a traffic engineered path

    B

    another name for a Frame Relay PVC

    C

    a bidirectional path through a network

    D

    a unidirectional path through a network


    正确答案： B
    解析： 暂无解析

  • 第12题：

    单选题
    In regard to a hub and spoke Frame-Relay data network, what kind of physical network is it classified as?（）
    A

    point-to-point

    B

    broadcast multi-access

    C

    nonbroadcast multipoint

    D

    nonbroadcast multi-access

    E

    broadcast point-to-multipoint


    正确答案： C
    解析： 暂无解析

  • 第13题：

    A new frame－relay network is being implemented and inverse ARP does not appear to be operating correctly. Which alternative command can be used to provide connectivity?()

    A. frame-relay arp

    B. frame-relay map

    C. frame-relay interface-dlci

    D. frame-relay lmi-type

    E. frame-relay pvc


    参考答案：B

  • 第14题：

    In regard to a hub and spoke Frame-Relay data network, what kind of physical network is it classified as?（）

    • A、point-to-point
    • B、broadcast multi-access
    • C、nonbroadcast multipoint
    • D、nonbroadcast multi-access
    • E、broadcast point-to-multipoint

    正确答案:D

  • 第15题：

    What does FRTP stand for？（）

    • A、Frame Relay Top Pseudowire
    • B、Frame Relay Traffic Pseudowire
    • C、Frame Relay Traffic Protocol
    • D、Frame Relay Traffic Policing

    正确答案:D

  • 第16题：

    what is the purpose of frame-relay LMI？


    正确答案: Local Management Interface
    The LMI is used to exchange messages and information on the state of a connection. Using the LMI， both ends of a Frame Relay connection can communicate with each other to determine the status of the PVC， the DLCI value defined for the connection， whether the interface is active and so on.

  • 第17题：

    The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）

    • A、The Gallant router has the wrong LMI type configured
    • B、Inverse ARP is providing the wrong PVC information to the Gallant router
    • C、The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
    • D、The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
    • E、The IP address on the serial interface of the Attalla router is configured incorrectly

    正确答案:D

  • 第18题：

    Customer X has a hub-and-spoke Frame Relay network， with a central office and two branch offices （RemoteA and RemoteB）. Each location has only one physical link to the Frame Relay cloud and RemoteB has a router that is not a Cisco router. Since the installation， there is no connectivity between RemoteB and the central office. What is a possible solution to this issue？ （）

    • A、 Because Frame Relay IETF encapsulation is only configurable at interface level， you must use IETF encapsulation on all routers.
    • B、 This is not a possible scenario. A dedicated Frame Relay link to RemoteB is mandatory at the central office.
    • C、 The router at RemoteB must be replaced by a Cisco router.
    • D、 Use Frame Relay IETF encapsulation on a per-VC basis on the central office router.
    • E、 There is a problem in the Frame Relay cloud， because Cisco routers are compatible with IETF Frame Relay.

    正确答案:D

  • 第19题：

    A default Frame Relay WAN is classified as what type of physical network？（）

    • A、point-to-point
    • B、broadcast multi-access
    • C、nonbroadcast multi-access
    • D、nonbroadcast multipoint.broadcast point-to-multipoint

    正确答案:C

  • 第20题：

    What is a Label-Switched Path?（）

    • A、a traffic engineered path
    • B、another name for a Frame Relay PVC
    • C、a bidirectional path through a network
    • D、a unidirectional path through a network

    正确答案:D

  • 第21题：

    单选题
    In order to troubleshoot an issue with the Testking frame relay network, you log into a remote router via a telnet session and issue the command "debug frame-relay lmi". After a long wait, you fail to see any output. What could be the cause of this problem?（）
    A

    The IP addresses are configured incorrectly.

    B

    Frame Relay LMI messages not displayed in real time.

    C

    The administrator must issue the enable frame-relay lmi debug command.

    D

    The administrator must issue the terminal monitor command.

    E

    Debug messages can only be received once through the console port.

    F

    The administrator must issue the show frame-relay lmi vty 0 4 command


    正确答案： C
    解析： 暂无解析

  • 第22题：

    单选题
    What is required to enable fragmentation of large FTP packets when voice quality on the network is affected by FTP transfers?（）
    A

    Configure TCP header compression on interface

    B

    Configure MPL on the Frame Relay interfaces

    C

    Configure FRF 12 fragmentation on the Frame Relay interfaces

    D

    Fragmentation is not supported with service internetworking


    正确答案： A
    解析： 暂无解析

  • 第23题：

    单选题
    A network administrator needs to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface for this connection?（）
    A

    Router(config-if)# encapsulation frame-relay q933a

    B

    Router(config-if)# encapsulation frame-relay ansi

    C

    Router(config-if)# encapsulation frame-relay ietf

    D

    Router(config-if)# encapsulation frame-relay isl

    E

    None of the above


    正确答案： E
    解析： 暂无解析

  • 第24题：

    单选题
    A default Frame Relay WAN is classified as what type of physical network（）。
    A

    point-to-point

    B

    broadcast multi-access

    C

    nonbroadcast multi-access

    D

    nonbroadcast multipoint

    E

    broadcast point-to-multipoint


    正确答案： C
    解析： 暂无解析

相关内容