当前分类： JN0-311
问题：多选题Which two configurations are made using the QoS Setup Wizard? （）(Choose two.)AAssign applications to traffic classes.BUse ToS/DSCP values for traffic classes.CExclude subnets from QoS management.DSelect dedicated vs. over-subscribed circuits....
查看答案
问题：多选题Which two statements are true when source/destination filters are enabled? （）(Choose two.)AExcluded traffic is not accelerated.BExcluded traffic is only compressed.CSource/destination filter applies to all traffic sent from LAN to WAN.DSource/destinati...
问题：单选题How do you verify connectivity between the default gateway and a WX device?（）A Check the WX device remote interface and verify that the status is up.B From the WX device, ping the default gateway to make sure it is reachable.C In WebView, check the ser...
问题：多选题Exchange acceleration is not working. Which three steps should you use to troubleshoot the problem? （）(Choose three.)ADetermine if CIFS acceleration is enabled.BDetermine if TCP Acceleration (AFP) is enabled.CDetermine if Forward Error Correction is en...
问题：多选题Which two functions are performed in Quick Setup?（） (Choose two.)Aoperating modeBauto-deploymentCspeed and duplex settingsDregistration server designation...
问题：多选题Which two statements describe the criteria bandwidth detection uses to dynamically alter bandwidth allocation?（）(Choose two.)AThroughput is raised as latency decreases.BThroughput is based on available bandwidth.CThroughput is lowered as latency decrea...
问题：多选题What are two instances when a WX device route carves? （）(Choose two.)AIt occurs every 29 hours.BPacket interception mode is enabled.CThe host is unreachable on the local subnet.DThe subnet is unreachable using the advertised router....
问题：多选题Which three ports does a WX device use for control traffic purposes?（） (Choose three.)A3577 UDPB3578 UDPC3678 UDPD3577 TCPE3578 TCP...
问题：多选题What happens when you enable QoS bandwidth detection? （）(Choose two.)ACircuit speed is reduced by 2% for overhead.BWAN speed can be configured to the LAN speed.CBandwidth is adjusted based on minimum and maximum settingsDWAN bandwidth is detected based...
问题：多选题Which three types of optimization does the WX 60 device perform when Exchange 2000 and Outlook 2000 are used in the network? （）(Choose three.)AFast Connection SetupBTCP Acceleration (AFP)CNetwork Sequence CachingDAppFlow's MAPI accelerationEMolecular S...
问题：单选题Why is SNMPv2 used to monitor the WX platform?（）A SNMPv1 is read-only on WX devices.B SNMPv1 is not supported by WX devices.C SNMPv2 supports both 32- and 64-bit counters.D SNMPv2 does put and get commands to WX devices....
问题：单选题What is one way to escape hardware bypass mode?（）A Reset the cabling.B Power cycle the device.C Bounce the service tunnels.D Unlock the device from the console....
问题：多选题What are three characteristics of NSC technology? （）(Choose three.)ANSC operates at the file level.BNSC operates at the byte level.CNSC uses hard drives to store longer patterns.DNSC retains learned patterns for a longer time.ENSC is available only on ...
问题：多选题What are two features of Packet Flow Acceleration?（） (Choose two.)APolicy-Based MultipathBTCP Acceleration (AFP)CForward Error CorrectionDMolecular Sequence Reduction...
问题：多选题Which three locations in WebView allow you to confirm that the endpoints are configured properly? （）(Choose three.)AMonitor EndpointsBAcceleration EndpointsCDevice Setup EndpointsDCompression EndpointsEAdmin Maintenance Display Configuration...
问题：多选题Which two scenarios would benefit the most from TCP Acceleration? （）(Choose two.)Alow-latency networksBhigh-latency networksClong-haul, low-bandwidth linksDlong-haul, high-bandwidth links...
问题：多选题What are three key pre-installation/configuration considerations when deploying a WX device?（） (Choose three.)AcablingBcommunity topologyCrequires a license keyDrequires two IP addressesEregistration server designation...
问题：单选题Which statement about the WebView submit command is true?（）A The submit command exits the GUI.B The submit command reboots the WX device.C The submit command saves and writes the configuration to flash.D The submit command is the same as the commit CLI...
