多选题What are two commands that can be used to configure MBGP for multicast?（）AUnder the BGP group, configure family inet any.BUse the set protocol MBGP command to enable MBGP.CUnder the BGP group, configure family inet multicast.DUse the set rib-group comm

第1题：

第2题：

第3题：

You wish to configure IPv6 support on a router which does not have any current IPv4 configuration.Which three steps are used to configure IPv6 with an accompanying IGP in JUNOS software? （）

• A、set protocols isis inet6
• B、set routing-options router-id router-id
• C、set protocols ospf3 area 0 interface all
• D、set interface fe-0/0/1 unit 0 family inet6
• E、set routing-options ipv6-router-id router-id

第4题：

What are two commands that can be used to configure MBGP for multicast？（）

• A、Under the BGP group， configure family inet any
• B、Use the set protocol MBGP command to enable MBGP
• C、Under the BGP group， configure family inet multicast
• D、Use the set rib-group command to copy the multicast routes into inet.1

第5题：

What are commands that can be used to configure MBGP for multicast？（）

• A、Under the BGP group， configure family inet any
• B、Use the set protocol MBGP command to enable MBGP
• C、Under the BGP group， configure family inet multicast
• D、Use the set rib-group command to copy the multicast routes into inet.1

第6题：

In a PIM topology using anycast RP, in which two ways can the RPs share group information? （）

• A、Configure MSDP between RPs.
• B、Redistribute multicast information in your IGP.
• C、Advertise S, G entries using MBGP.
• D、Configure PIM to advertise group information between RPs.

第7题：

Which of the following are steps to configure destination-based Remote Triggered Black Hole（RTBH）filtering？（）

• A、Configure OSPF between trigger router and black hole routes
• B、Configure all edge routers with static （reserved） host route to Null0
• C、Configure BGP beteen trigger and black hole routers
• D、Configure on trigger router to advertise victim host route with commumity
• E、Activate black hole by redistributing route for victim into BGP with next-hop set to the static（reserved）host route configured on edge routers

第8题：

You have been asked to configure your router to send link-related SNMP trap notifications to the network management system (NMS) located at address 172.16.17.1.Which two commands are required?（）

• A、set snmp trap-group my-trap-group targets 172.16.17.1
• B、set snmp targets 172.16.17.1
• C、set snmp trap-group my-trap-group link-status
• D、set snmp trap-group my-trap-group categories link

第9题：

Your company has an Active Directory Domain Services (AD DS) domain. All client computers run Windows 7. You have a Remote Desktop Session Host (RD Session Host) server. You need to ensure that computer identities are validated before user authentication is performed. What should you do?（）

• A、Configure the Set RD Gateway authentication method Group Policy setting to Use smart card.
• B、Configure the Set RD Gateway authentication method Group Policy setting to Use locally logged-on credentials.
• C、Enable the Configure server authentication for client Group Policy setting and then select Do not connect if authentication fails.
• D、Enable the Configure server authentication for client Group Policy setting and then select Always connect, even if authentication fails.

第10题：

第11题：

第12题：

第13题：

第14题：

第15题：

Which two functions can be configured on the ERX Edge Router to support MBGP? （）(Choose two.)

• A、address-family ipv4 unicast
• B、address-family vpnv4 unicast
• C、address-family ipv4 multicast
• D、address-family vpnv4 multicast

第16题：

Which statement would prevent the sending of redundant route advertisements when your routereflector cluster is fully meshed?（）

• A、set protocols bgp group mygroup path-selection cisco-non-deterministic;
• B、set protocols bgp group i-bgp no-aggregator-id;
• C、set protocols bgp group mygroup no-client-reflect;
• D、set protocols bgp group i-bgp damping;

第17题：

For maintaining separate unicast and multicast forwarding topologies, where should MBGP multicast routes be placed?（）

• A、inet.0
• B、inet.1
• C、inet.2
• D、inet.4

第18题：

Which statement correctly describes IPsec VPN backup technology？（）

• A、The cypto isakmp keepalive command is used to configure the Stateful Switchover （SSO）protocol
• B、Reverse Route Injection （RRI） is configured on at the remote site to inject the central sitenetworks
• C、Each Hot Standby Routing Protocol （HSRP） standby group has two well-known MACaddresses and a virtual IP address
• D、The cypto isakmp keepalive command is used to configure stateless failover

第19题：

What are two commands that can be used to configure MBGP for multicast?（）

• A、Under the BGP group, configure family inet any.
• B、Use the set protocol MBGP command to enable MBGP.
• C、Under the BGP group, configure family inet multicast.
• D、Use the set rib-group command to copy the multicast routes into inet.1.

第20题：

Which two commands may be used when configuring an IP address for a Gigabit Ethernet interface?（）

• A、set interfaces ge-0/0/0.0 address 10.1.1.1/24
• B、set interfaces ge-0/0/0.0 family inet address 10.1.1.1/24
• C、set interfaces ge-0/0/0 unit 0 family inet address 10.1.1.1/24
• D、set interfaces ge-0/0/0 address 10.1.1.1/24

第21题：

You manage a server named Server2 that runs Windows Server 2008. You install and test the Terminal Services role on Server2. You publish an application by using Terminal Services. All users must connect to the Terminal Services application by using the Remote Desktop Protocol.  You install and configure the Terminal Services Gateway （TS Gateway） role service on Server2. You configure a default domain policy to enable the Enable Connection through TS Gateway setting. Users report that they cannot connect to the Terminal Services application.  You need to ensure that users can access the Terminal Services application on the intranet and from the Internet.  What should you do？（）

• A、Configure the Enable Connection through TS Gateway Group Policy setting to Disabled.
• B、Configure the Set TS Gateway server address Group Policy and configure the IP address of the TSGateway server. Link the GPO to the domain.
• C、Configure Server Authentication on the Remote Desktop Connection client to Always connect， even if server authentication fails for all users.
• D、Enable the Set TS Gateway server authentication method Group Policy to the Ask for credential， use NTLM protocol setting. Link the GPO to the domain.

第22题：

第23题：

第24题：