单选题When configuring an interface using SMIT and Further Configuration with an IP address and netmask， which of the following outcomes indicates how the routing tables will be affected？（）A A subnet route is automatically addedB A default route is automatic

第1题：

第2题：

第3题：

What does the ip access-routes configuration command accomplish?（）

• A、It statically places a host route in the routing table.
• B、It statically associates an IP address with a customer.
• C、It dynamically creates a host route in the routing table.
• D、It dynamically assigns an address to the router's interface

第4题：

Which three statements are true about EIGRP route summarization?（）

• A、When manual summarization is configured, the router immediately creates a route that points to null0 interface
• B、Manual route summarization  is configured in router configuration mode when the router is configured for EIGRP routing
• C、Manual route summarization is configured on the interface
• D、The ip summary - address eigrp command generates a default route with an administrative distance  of 5
• E、When manual summarization is configured, the summary route will use the metric of the largest specific metric of the summary routes
• F、The ip summary - address eigrp command generates a default route with an administrative distance of 90

第5题：

Which two are advantages of static routing when compared to dynamic routing?（）

• A、Security increases because only the network administrator may change the routing tables
• B、Configuration complexity decreases as network size increases
• C、Routing updates are automatically sent to neighbors
• D、Route summarization is compued automatically by the router
• E、Routing traffic load is reduced when used in stub network links
• F、An efficient algorithm is used to build routing tables,using automatic updates
• G、Routing tables adapt automatically to topology changes.

第6题：

The following configuration command was entered into a router:ip route 172.16.3.0 255.255.255.0 192.168.2.4 Which of the following statements are true regarding this configuration change?（）

• A、The default administrative distance is used.
• B、The command is used to establish a static route.
• C、The command is used to configure the router interfaces.
• D、The command is used to establish a stub network.
• E、The subnet mask for the source address is 255.255.255.0

第7题：

A system is experiencing packet routing problems，when the administrator runs ’netstat -nr’ the following default routes are displayed： default165.253.251.1UG51601304 en8-- default192.168.50.1UGH01590450 en4--   Assuming the first route is correct，how can the administrator remove the incorrect default route？（）

• A、route delete default 192.168.50.1
• B、access smit with the route_remove shortcut
• C、chdev -l inet0 -a delroute=net，-hopcount，0，，192.168.50.1
• D、flush the routing table from the console and configuring the 165.253.251.1 route

第8题：

第9题：

第10题：

第11题：

第12题：

第13题：

第14题：

When configuring a routed port on a Cisco multilayer switch， which of these is a required configuration task that you must perform to enable that port to function as a routed port？ （）

• A、Enable the switch to participate in routing updates from external devices with the router command in global configuration mode.
• B、Enter the no switchport command to disable Layer 2 functionality at the interface level.
• C、Each port participating in routing of Layer 3 packets must have an IP routing protocol assigned on aperinterface level.
• D、Routing is enabled by default on a multilayer switch， so the port can become a Layer 3 routing interface by assigning the appropriate IP address and subnet information.

第15题：

When you display the routing table by entering the show route command, what does the* indicate?（）

• A、The route is a direct route.
• B、The route was selected as active.
• C、The route is a default route.
• D、The route was learned using a dynamic routing protocol.

第16题：

Which two are advantages of static routing when compared to dynamic routing？（）

• A、Security increases because only the network administrator may change the routing tables.
• B、Configuration complexity decreases as network size increases.
• C、Routing updates are automatically sent to neighbors.
• D、Route summarization iscompued automatically by the router.
• E、Routing traffic load is reduced when used in stub network links
• F、An efficient algorithm is used to build routing tables，using automatic updates.
• G、Routing tables adapt automatically to topology changes.

第17题：

Which two are advantages of static routing when compared to dynamic routing?（）

• A、Security increases because only the network administrator may change the routing tables.
• B、Configuration complexity decreases as network size increases.
• C、Routing updates are automatically sent to neighbors.
• D、Route summarization iscompued automatically by the router.
• E、Routing traffic load is reduced when used in stub network links.
• F、An efficient algorithm is used to build routing tables,using automatic updates.
• G、Routing tables adapt automatically to topology changes.

第18题：

When configuring an interface using SMIT and Further Configuration with an IP address and netmask， which of the following outcomes indicates how the routing tables will be affected？（）

• A、A subnet route is automatically added
• B、A default route is automatically added
• C、All other routes are automatically added
• D、The routing table is not affected

第19题：

You are configuring the DX appliance for the first time using the console. Which two configurationvalues can be set using the first time configuration screen?（） (Choose two.)

• A、the user role
• B、the ether0 IP address
• C、the default route for this DX appliance
• D、the address of a network TFTP server

第20题：

第21题：

第22题：

第23题：

第24题：