What must be configured prior to the first commit after factory defaults are loaded?（）A、root authenticationB、default gatewayC、hostnameD、management services

第1题：

When configuring the Cisco VPN Client，what action is required prior to installing Mutual Group Authentication？（）

• A、Transparent tunneling must be enabled.
• B、A valid root certificate must be installed.
• C、A group pre-shared secret must be properly configured.
• D、The option to "Allow Local LAN Access" must be selected.

第2题：

What is one configuration method for loading a factory default configuration onto a J-series router？（）

• A、load override reset
• B、load factory-default
• C、rollback factory-default
• D、request system factory-default

第3题：

An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location？ （）

• A、The switch must be configured with an IP address,subnet mask,and default gateway.
• B、The switch must be connected to a router over a VLAN trunk.
• C、The switch must be reachable through a port connected to its management VLAN.
• D、The switch console port must be connected to the Ethernet LAN.
• E、The switch management VLAN must be created and have a membership of at least one switch port.
• F、The switch must be fully configured as an SNMP agent.

第4题：

Prior to implementing an LPAR system， which of the following needs to be done？（）

• A、A graphics monitor must be attached to the server
• B、Cluster System Management （CSM） software must be installed
• C、The LPAR system must have an Hardware Management Console （HMC） connected
• D、Each LPAR must be configured with a CDROM for operating system installation

第5题：

Which two statements are true regarding rescue configurations?（）

• A、Once saved, a rescue configuration is loaded using the rollback 0 command.
• B、The rescue configuration must contain the minimal elements necessary to restore network connectivity.
• C、A minimal rescue configuration is defined by default.
• D、A rescue configuration must include a root password.

第6题：

You want to log into the router and make a configuration change.After loggin in as the root user, what is the next command you must enter?（）

• A、enable
• B、configure
• C、edit
• D、cli

第7题：

What must be configured prior to the first commit after factory defaults are loaded?（）

• A、root authentication
• B、default gateway
• C、host name
• D、management services

第8题：

You work as the IT professional in an international company which is named Wiikigo. You are experiencedin implementing and administering a network operating system. You are specialized in deploying servers，configuring Windows Server 2008 Terminal services and network application services， and configuring aweb services infrastructure. There is an Active Directory domain in your company. The company runsTerminal Services. You have the head office printer configured as the default printer on the TerminalServer. According to the requirements of the company policy， all remote client computers must meet thefollowing requirements： Users must be able to access their local printers during a terminal session. The head office printer must bethe default printer of the client computers. A Group Policy object （GPO） needs to be created by using theTerminal Services Printer Redirection template to meet the company policy. What action should you perform？（）

• A、The Do not set default client printer should be set to be default printer in a session option to Enabled.The GPO should be applied to all the client computers.
• B、The Easy Print driver first option should be set to Disabled. The GPO should be applied to the Terminal Server.
• C、The Use Terminal Services Easy Print driver first option should be set to Disabled. The GPO should be applied to all the client computers.
• D、The Do not set default client printer should be set to be default printer in a session option to Enabled.The GPO should be applied to the Terminal Server.

第9题：

第10题：

第11题：

第12题：

第13题：

After factory-defaults have been loaded, which two syslog files will be present in the configuration?（）

• A、system and chassisd
• B、syslog-messages and NVRAM
• C、messages and interactive-commands
• D、authorization and events

第14题：

To enable a tty port to be used for a cu session what must be done to the system？（）

• A、smit tty； take the defaults and create the desired tty
• B、In the /etc/uucp Devices add a line similar to： Direct ttyX - 9600 direct
• C、Install bos.net.uucp and the first available tty will be configured for use by a cu session
• D、Run the Asynchronous Terminal Emulation （ATE） program and it will configure a tty port for a cu session

第15题：

An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）

• A、The switch must be configured with an IP address, subnet mask, and default gateway.
• B、The switch must be connected to a router over a VLAN trunk.
• C、The switch must be reachable through a port connected to its management VLAN.
• D、The switch console port must be connected to the Ethernet LAN.
• E、The switch management VLAN must be created and have a membership of at least one switch

第16题：

A client tried to upgrade the system firmware on a p5 590, but it failed. What is the minimum requirement to update the system firmware from the HMC if inventory scout is already installed?（）

• A、A public internet connection
• B、All of the Logical Partitions need to be active
• C、One partition must be configured with Service Authority
• D、A local Repository must be configured prior to the update

第17题：

What must be configured prior to the first commit after factory defaults are loaded?（）

• A、root authentication
• B、default gateway
• C、hostname
• D、management services

第18题：

How can you reset your router or switch to factory defaults?（）

• A、reset configuration
• B、load factory-default
• C、load override default
• D、set default configuration

第19题：

What must be configured prior to the first commit after factory defaults are loaded?（）

• A、root authe ntication
• B、default gateway
• C、hostname
• D、management services

第20题：

Your company has an Active Directory domain. The company runs Terminal Services. You configure the main office printer as the default printer on the Terminal Server.  The company policy states that all remote client computers must meet the following requirements： The main office printer must be the default printer of the client computers. Users must be able to access their local printers during a terminal session.  You need to create a Group Policy Object by using the Terminal Services Printer Redirection template to meet the company policy. What should you do？（）

• A、Set the Easy Print driver first option to Disabled. Apply the GPO to the Terminal Server.
• B、Set the Use Terminal Services Easy Print driver first option to Disabled. Apply the GPO to all the client computers.
• C、Set the Do not set default client printer to be default printer in a session option to Enabled. Apply the GPO to the Terminal Server.
• D、Set the Do not set default client printer to be default printer in a session option to Enabled. Apply the GPO to all the client computers.

第21题：

第22题：

第23题：

第24题：