What must be configured prior to the first commit after factory defaults are loaded?（）A、root authenticationB、default gatewayC、hostnameD、management services

题目

What must be configured prior to the first commit after factory defaults are loaded?（）

  • A、root authentication
  • B、default gateway
  • C、hostname
  • D、management services
相似考题

1.What is true about a Bypass Tunnel in MPLS Fast Reroute?()A. Only configured on the egress routerB. Only configured on the ingress routerC. Is pre-signalled to reduce packet lossD. Must intersect the primary LSP at two locations

2.When configuring the Cisco VPN Client，what action is required prior to installing Mutual Group Authentication？（）A、Transparent tunneling must be enabled.B、A valid root certificate must be installed.C、A group pre-shared secret must be properly configured.D、The option to "Allow Local LAN Access" must be selected.

3.What is true about a Bypass Tunnel in MPLS Fast Reroute?（）A、Only configured on the egress routerB、Only configured on the ingress routerC、Is pre-signalled to reduce packet lossD、Must intersect the primary LSP at two locations

4.Which three options are prerequisites to configuring Cisco AutoOoS？（）A、Cisco Express Forwarding （CEF） must be globally enabled.B、Prior to the enabling of the Cisco AutoOoS feature， the bandwidth command must be applied on all interfaces or subinterfaces.C、After the enabling of the Cisco AutoOoS feature， the bandwidth command must be applied on all interfaces or subinterfaces .D、OoS policies must be enabled on all interfaces that will participate in the AutoOoS configuration.E、An IP address must be configured on all low-bandwidth interfaces （768 kb/s or lower） that will participate in the AutoOoS configurationF、An IP address must be configured on all interfaces that will participate in the AutoOoS configuration

更多“What must be configured prior to”相关问题

  • 第1题：

    An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network. What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）

    • A、The switch that will share its VLAN configuration must be in VTP server mode.
    • B、The switches must be in the same VTP domain.
    • C、The switch that will share the VLAN information must be configured as the root bridge.
    • D、The switches must be connected over VLAN trunks.
    • E、The switches must be configured to use the same STP version.
    • F、The switches must have VTP pruning activated.

    正确答案:A,B,D

  • 第2题：

    Prior to 802.1w，Cisco implemented a number of proprietary enhancements to 802.1D to improve convergence in a Layer 2 network. Which statement is correct？（）

    • A、Only UplinkFast and BackboneFast are specified in 802.1w；PortFast must be manually configured.
    • B、Only PortFast is specified in 802.1w；UplinkFast and BackboneFast must be manually configured.
    • C、None of the proprietary Cisco enhancements are specified in 802.1w.
    • D、PortFast，UplinkFast，and BackboneFast are specified in 802.1w.

    正确答案:D

  • 第3题：

    A client has tried to update the firmware of an Ethernet adapter on a p5 590, however it repeatedly fails. What is the most likely cause of this problem?（）

    • A、The adapter must be taken offline prior to the firmware update
    • B、The adapter must be assigned to the service partition prior to the firmware update
    • C、The system has not been rebooted since the adapter was added to the Logical Partition
    • D、The adapter must be dynamically removed from the Logical Partition prior to the firmware update

    正确答案:A

  • 第4题：

    An administrator issued a command to update the firmware of an Ethernet adapter on a partitioned system， but received an error. What is the most likely cause of the problem？（）

    • A、The adapter must be taken offline prior to the firmware update.
    • B、The system has not been rebooted since the adapter was added to the LPAR.
    • C、The adapter must be assigned to the service partition prior to updating the firmware.
    • D、The adapter must be dynamically removed from the LPAR prior to updating the firmware.

    正确答案:A

  • 第5题：

    多选题
    An administrator is configuring a Catalyst switch with VLAN information that must be automatically distributed to other Catalyst switches in the network. What conditions must be met in order for the VLANs configured on this switch to be automatically configured on the other switches?（）
    A

    The switch that will share its VLAN configuration must be in VTP server mode.

    B

    The switches must be in the same VTP domain.

    C

    The switch that will share the VLAN information must be configured as the root bridge.

    D

    The switches must be connected over VLAN trunks.

    E

    The switches must be configured to use the same STP version.

    F

    The switches must have VTP pruning activated.


    正确答案： A,B,D
    解析： 暂无解析

  • 第6题：

    多选题
    What are two requirements when using AppFlow? （）(Choose two.)
    A

    Quality of service must be enabled.

    B

    NSC compression must be enabled.

    C

    PFA's TCP Acceleration (AFP) must be enabled.

    D

    AppFlow must be configured on the client-side device first


    正确答案： B,C
    解析： 暂无解析

  • 第7题：

    多选题
    The hardware and software configurations for vPC+ are similar to that of traditional vPC. What are the differences in the configuration of vPC+？ （）
    A

    FabricPath switch ID must be configured under the vPC domain.

    B

    Virtual switch ID of vPC+ must be configured under FabricPath domain.

    C

    On Cisco Nexus 7000 Series Switch， F1 interfaces must be used as the vPC+ peer links.

    D

    The vPC+ peer link must be configured as a Cisco FabricPath core port （switchport mode fabricpath）.

    E

    FabricPath subswitch ID must be configured under the vPC domain.


    正确答案： A,C
    解析： 暂无解析

  • 第8题：

    单选题
    When configuring vlans on an autonomous access point. What must be configured on the connected switchport？（）
    A

    802.1q trunking

    B

    vtp trunking

    C

    isl trunking

    D

    dpt trunking


    正确答案： B
    解析： 暂无解析

  • 第9题：

    单选题
    What must be configured prior to the first commit after factory defaults are loaded?（）
    A

    root authentication

    B

    default gateway

    C

    hostname

    D

    management services


    正确答案： A
    解析： 暂无解析

  • 第10题：

    单选题
    Prior to implementing an LPAR system， which of the following needs to be done？（）
    A

    A graphics monitor must be attached to the server

    B

    Cluster System Management （CSM） software must be installed

    C

    The LPAR system must have an Hardware Management Console （HMC） connected

    D

    Each LPAR must be configured with a CDROM for operating system installation


    正确答案： A
    解析： 暂无解析

  • 第11题：

    单选题
    What is a limitation of implementing uRPF？（）
    A

    MPLS LDP must be enabled.

    B

    BGP routing protocol must be running.

    C

    Named access-lists must be configured.

    D

    Symmetrical routing is required.

    E

    Domain name must be defined


    正确答案： E
    解析： 暂无解析

  • 第12题：

    What is a limitation of implementing uRPF？（）

    • A、MPLS LDP must be enabled.
    • B、BGP routing protocol must be running.
    • C、Named access-lists must be configured.
    • D、Symmetrical routing is required.
    • E、Domain name must be defined

    正确答案:D

  • 第13题：

    You have just reinstalled a VIP 6-80 in a Cisco 7500 Series router. What must you do to bring up the port adapter interfaces?（）

    • A、All interfaces are online by default once the VIP is up and running normally.
    • B、All interfaces must be manually brought online, even those previously configured.
    • C、The previous VIP configuration must be reloaded to bring interfaces online.
    • D、Any interfaces not previously configured must be manually configured and brought online.

    正确答案:D

  • 第14题：

    Prior to implementing an LPAR system， which of the following needs to be done？（）

    • A、A graphics monitor must be attached to the server
    • B、Cluster System Management （CSM） software must be installed
    • C、The LPAR system must have an Hardware Management Console （HMC） connected
    • D、Each LPAR must be configured with a CDROM for operating system installation

    正确答案:C

  • 第15题：

    A client tried to upgrade the system firmware on a p5 590, but it failed. What is the minimum requirement to update the system firmware from the HMC if inventory scout is already installed?（）

    • A、A public internet connection
    • B、All of the Logical Partitions need to be active
    • C、One partition must be configured with Service Authority
    • D、A local Repository must be configured prior to the update

    正确答案:C

  • 第16题：

    多选题
    What are two requirements when using AppFlow?（） (Choose two.)
    A

    Quality of service must be enabled.

    B

    NSC compression must be enabled.

    C

    PFA's TCP Acceleration (AFP) must be enabled.

    D

    AppFlow must be configured on the client-side device first.


    正确答案： A,C
    解析： 暂无解析

  • 第17题：

    单选题
    When configuring VLANs on an autonomous access point，what must be configured on theconnected switchport？（）
    A

    802.1q trunking

    B

    VTP trunking

    C

    ISL trunking

    D

    DPT trunking


    正确答案： C
    解析： 暂无解析

  • 第18题：

    单选题
    What must be configured on the Cisco Unity Express host router prior to installation of the CUE module?（）
    A

    Set up the Network Time Protocol server. 

    B

    Install the files needed to run the web-based GUI. 

    C

    Set up routing and IP addressing on the service module and the interface service engine. 

    D

    Configure a session initiation protocol dial peer for connecting calls to the voice mail and Auto Attendant features.


    正确答案： D
    解析： 暂无解析

  • 第19题：

    单选题
    An administrator issued a command to update thefirmware of an Ethernet adapter on a partitioned system, but received an error. What is the most likely cause of the problem?（）
    A

    The adapter must be taken offline prior to the firmware update.

    B

    The system has not been rebooted since the adapter was added to the LPAR.

    C

    The adapter must be assigned to the service partition prior to updating the firmware.

    D

    The adapter must be dynamically removed from the LPAR prior to updating thefirmware.


    正确答案： D
    解析： 暂无解析

  • 第20题：

    单选题
    A client tried to upgrade the system firmware on a p5 590, but it failed. What is the minimum requirement to update the system firmware from the HMC if inventory scout is already installed?（）
    A

    A public internet connection

    B

    All of the Logical Partitions need to be active

    C

    One partition must be configured with Service Authority

    D

    A local Repository must be configured prior to the update


    正确答案： A
    解析： 暂无解析

  • 第21题：

    单选题
    When configuring the Cisco VPN Client，what action is required prior to installing Mutual Group Authentication？（）
    A

    Transparent tunneling must be enabled.

    B

    A valid root certificate must be installed.

    C

    A group pre-shared secret must be properly configured.

    D

    The option to Allow Local LAN Access must be selected.


    正确答案： A
    解析： 暂无解析

  • 第22题：

    单选题
    What must be configured prior to the first commit after factory defaults are loaded?（）
    A

    root authentication

    B

    default gateway

    C

    host name

    D

    management services


    正确答案： D
    解析： 暂无解析

相关内容