Hot Standby Router Protocol (HSRP) is able to provide network redundancy for IP networks. Concerning HSRP load sharing, which two descriptions make sense?（）A、It is achieved by using more than one HSRP group.B、It is done in regards to either round robin or

第1题：

HSRP has been configured between two Company devices.  Which of the following describe  reasons for deploying HSRP？ （）

• A、 HSRP provides redundancy and fault tolerance
• B、 HSRP allows one router to automatically assume the function of the second router if the second  router fails
• C、 HSRP allows one router to automatically assume the function of the second router if the second  router starts
• D、 HSRP provides redundancy and load balancing

第2题：

Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure.   Which two statements are true about the Hot Standby Router Protocol （HSRP）？ （）

• A、 Load sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers.  
• B、 Routers configured for HSRP can belong to multiple groups and multiple VLANs.
• C、 Load sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.
• D、 All routers configured for HSRP load balancing must be configured with the same priority.  
• E、 Routers configured for HSRP must belong to only one group per HSRP interface.

第3题：

What three tasks must a network administrator perform to properly configure Hot Standby Routing  Protocol （HSRP）？（）

• A、 Define the encapsulation type.
• B、 Define the standby router.
• C、 Define the standby IP address.
• D、 Enable the standby priority.

第4题：

Which three statements best describe HSRP configuration on Cisco Nexus switches？（）

• A、 In a vPC topology， the primary HSRP router will respond to ARP requests， but both HSRP routers will forward data traffic. No additional configuration is required.
• B、 In a vPC topology， the primary HSRP router will respond to ARP requests， but both HSRP routers will forward data traffic if the peer-gateway feature is enabled.
• C、 You can configure two overlapping HSRP groups to load share traffic from the connected hosts while providing the default router redundancy.
• D、 You can use the show standby command to verify HSRP operation and configuration.
• E、 If you remove the feature hsrp command， all relevant HSRP configuration information isalso removed.

第5题：

Which three of the following network features are methods used to achieve high availability（）

• A、Spanning Tree Protocol（STP）
• B、Delay reduction
• C、Hot Standby Routing Protocol（HSRP）
• D、Dynamic routing protocols
• E、Quality of Service（QoS）
• F、Jitter management

第6题：

You have configured router R1 with HSRP， using the standard defaults.  Which three statements  are true of a default HSRP configuration？（）

• A、 The Standby hello time is 2 seconds.
• B、 Two HSRP groups are configured.
• C、 The Standby track interface priority is 10.
• D、 The Standby hold time is 10 seconds
• E、 The Standby priority is 100.
• F、 The Standby delay is 3 seconds.

第7题：

For the following protocols， which one provides a mechanism to transparently intercept and redirect CIFS traffic from a client to a local Cisco Wida Area Application engine？（）

• A、Virtual Router Redundancy Protocol（VRRP）
• B、File Transport Protocol（FTP）
• C、Hot Standby Routing Protocol（HSRP）
• D、Web Cache Communication Protocol（WCCP）

第8题：

第9题：

第10题：

第11题：

第12题：

第13题：

When HSRP is configured on a network, which two of these items are provided, which are shared between the routers that run HSRP ?（） (choose two)

• A、Shared single interface
• B、IP Address
• C、TCP-based hello packets
• D、MAC address

第14题：

pany uses GLBP to provide for router redundancy in the network.  Which describes the default  load balancing scheme used by the Gateway Load Balancing Protocol （GLBP）？（）

• A、 Per host basis using a strict priority scheme
• B、 Per session using a round-robin scheme
• C、 Per session using a strict priority scheme
• D、 Per GLBP group using a strict priority scheme
• E、 Per host basis using a round-robin scheme
• F、 Per GLBP group using a round-robin scheme

第15题：

HSRP. Known as Hot Stanclby Router Protocol, is a Cisco proprietarv redundancy protocol . As an experienced network administrator, you are required to configure HSRP on a XYZ network. Which TWO of the following wii be available and shared between the routers configured with HSRP? （）(Choose two.)

• A、a shared single interface
• B、the ability to track serial interfaces
• C、UDP-based hello packets
• D、the impact of flapping links if timers are too low

第16题：

Router R1 and R2 are both configured for HSRP.  Which two statements about the HSRP priorities  of these two routers are true？（）

• A、 To assign the HSRP router priority in a standby group， the standby group-number priority  priority-value global configuration command must be used.
• B、 The default priority of a router is zero （0）.
• C、 The no standby priority command assigns a priority of 100 to the router.
• D、 Assuming that preempting has also been configured， the router with the lowest priority in an  HSRP group would become the active router.
• E、 When two routers in an HSRP standby group are configured with identical priorities， the router  with the highest configured IP address will become the active router.

第17题：

You need to decide on the best router redundancy protocol to use in the Company network.  Which  two statements are true about HSRP， VRRP， and GLBP？（）

• A、 GLBP and VRRP allow for MD5 authentication， whereas HSRP does not.
• B、 HSRP allows for multiple upstream active links being simultaneously used， whereas GLBP  does not.
• C、 GLBP allows for router load balancing of traffic from a network segment without the different  host IP configurations required to achieve the same results with HSRP.
• D、 Unlike HSRP and VRRP， GLBP allows automatic selection and simultaneous use of multiple  available gateways.
• E、 GLBP allows for router load balancing of traffic from a network segment by utilizing the creation  of multiple standby groups.

第18题：

Which two of the following statements are true about HSRP load sharing?（） (Choose two)

• A、It is achieved by using more than one HSRP group.
• B、It is done in regards to either round robin or weight basis.
• C、It is used to offload the active router in a certain HSRP group.
• D、Single group HSRP is used to achieve more efficient link utilization.
• E、The return traffic is influenced by HSRP load sharing configuration.

第19题：

第20题：

第21题：

第22题：

第23题：