You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）A. The Frame Relay encaps

题目

You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）

A. The Frame Relay encapsulation on the physical interface.

B. The local DLCI on each subinterface.

C. An IP address on the physical interface.

D. The subinterface type as point-to-point.

相似考题

1.You have a network containing 120 routers. You must establish and maintain connectivity between the loopback interfaces of all routers. Because of the critical services using the network, you need redundancy and fast failover. Which routing protocol should you use in this scenario?（）A. OSPFB. RIPC. BGPD. static

2.Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? ()A. frame-relay arpB. frame-relay mapC. frame-relay interface-dlciD. frame-relay lmi-type

3.Refer to the exhibit. You are the network administrator of the Route.com company. You have been tasked to implement a hub and spoke EIGRP topology over Frame Relay to provide connectivity between the networks at headquarters and all 300 spokes. Before you begin the actual implementation, which three pieces of information are more important to know than the others?（）A. the Committed Information Rate of all the Frame Relay PVCsB. the Cisco IOS version running on all the routersC. the router model number of all the spoke routersD. the number of HQ networks connected behind the headquarter routersE. the routing policy, such as whether or not the spokes can be used as backup transient point between the two headquarter routers

4.You install a new hardware router that provides wireless network connectivity between your computer and the Internet. You connect to the router by using a wireless network adapter.Your computer is able to access the Internet but is unable to discover other computers in the local wireless network.You need to configure the wireless connection to allow your computer to discover other computers.What should you do?（）A.AB.BC.CD.D

更多“You are implementing a new frame relay network to provide connectivity between you offices ”相关问题

  • 第1题：

    You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?()

    A. Show interface lmi

    B. Show frame-relay lmi

    C. Show interface frame-relay

    D. Debug frame-relay interface.


    参考答案：B

  • 第2题：

    When should traffic shaping be implemented on Frame Relay PVCs？（）

    • A、When you want to drop excess traffic above the CIR
    • B、When there is a speed mismatch between the central site and the remote site
    • C、When using Frame Relay SVCs
    • D、When over-subscribing the central site link
    • E、When LLQ is implemented on the Frame Relay PVC
    • F、When Multilink PPP LFI is implemented on the Frame Relay PVC

    正确答案:B,D

  • 第3题：

    In order to troubleshoot an issue with the Testking frame relay network, you log into a remote router via a telnet session and issue the command "debug frame-relay lmi". After a long wait, you fail to see any output. What could be the cause of this problem?（）

    • A、The IP addresses are configured incorrectly.
    • B、Frame Relay LMI messages not displayed in real time.
    • C、The administrator must issue the enable frame-relay lmi debug command.
    • D、The administrator must issue the terminal monitor command.
    • E、Debug messages can only be received once through the console port.
    • F、The administrator must issue the show frame-relay lmi vty 0 4 command

    正确答案:D

  • 第4题：

    you want to view the status of a frame relay connection. How to display the status of a Frame-Relay PVC？


    正确答案:show frame-relay pvc and show frame-relay map

  • 第5题：

    Customer X has a hub-and-spoke Frame Relay network， with a central office and two branch offices （RemoteA and RemoteB）. Each location has only one physical link to the Frame Relay cloud and RemoteB has a router that is not a Cisco router. Since the installation， there is no connectivity between RemoteB and the central office. What is a possible solution to this issue？ （）

    • A、 Because Frame Relay IETF encapsulation is only configurable at interface level， you must use IETF encapsulation on all routers.
    • B、 This is not a possible scenario. A dedicated Frame Relay link to RemoteB is mandatory at the central office.
    • C、 The router at RemoteB must be replaced by a Cisco router.
    • D、 Use Frame Relay IETF encapsulation on a per-VC basis on the central office router.
    • E、 There is a problem in the Frame Relay cloud， because Cisco routers are compatible with IETF Frame Relay.

    正确答案:D

  • 第6题：

    You are planning to connect your three branch offices to the corporate site via Frame Relay. The first branch office has been assigned the network 10.1.0.0/16， the second 10.2.0.0/16， the third 10.3.0.0/16， and the corporate headquarters uses 10.0.0.0/16. You would like to summarize all branch and corporate networks into a single route at the corporate site. Which network address and subnet mask should you choose？（）  

    • A、 10.0.0.0/24
    • B、 10.0.0.0/16
    • C、 10.0.0.0/14
    • D、 10.0.0.0/15

    正确答案:C

  • 第7题：

    You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）

    • A、The Frame Relay encapsulation on the physical interface.
    • B、The local DLCI on each subinterface.
    • C、An IP address on the physical interface.
    • D、The subinterface type as point-to-point.

    正确答案:C

  • 第8题：

    单选题
    You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）
    A

    The Frame Relay encapsulation on the physical interface.

    B

    The local DLCI on each subinterface.

    C

    An IP address on the physical interface.

    D

    The subinterface type as point-to-point.


    正确答案： B
    解析： 暂无解析

  • 第9题：

    单选题
    You have a network containing 120 routers. You must establish and maintain connectivity between the loopback interfaces of all routers. Because of the critical services using the network, you need redundancy and fast failover. Which routing protocol should you use in this scenario?（）
    A

    OSPF

    B

    RIP

    C

    BGP

    D

    static


    正确答案： D
    解析： 暂无解析

  • 第10题：

    单选题
    Customer X has a hub-and-spoke Frame Relay network， with a central office and two branch offices （RemoteA and RemoteB）. Each location has only one physical link to the Frame Relay cloud and RemoteB has a router that is not a Cisco router. Since the installation， there is no connectivity between RemoteB and the central office. What is a possible solution to this issue？ （）
    A

     Because Frame Relay IETF encapsulation is only configurable at interface level， you must use IETF encapsulation on all routers.

    B

     This is not a possible scenario. A dedicated Frame Relay link to RemoteB is mandatory at the central office.

    C

     The router at RemoteB must be replaced by a Cisco router.

    D

     Use Frame Relay IETF encapsulation on a per-VC basis on the central office router.

    E

     There is a problem in the Frame Relay cloud， because Cisco routers are compatible with IETF Frame Relay.


    正确答案： D
    解析： 暂无解析

  • 第11题：

    单选题
    You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?（）
    A

    Show interface lmi

    B

    Show frame-relay lmi

    C

    Show interface frame-relay

    D

    Debug frame-relay interface.


    正确答案： B
    解析： 暂无解析

  • 第12题：

    单选题
    You are planning to connect your three branch offices to the corporate site via Frame Relay. The first branch office has been assigned the network 10.1.0.0/16， the second 10.2.0.0/16， the third 10.3.0.0/16， and the corporate headquarters uses 10.0.0.0/16. You would like to summarize all branch and corporate networks into a single route at the corporate site. Which network address and subnet mask should you choose？（）
    A

     10.0.0.0/24

    B

     10.0.0.0/16

    C

     10.0.0.0/14

    D

     10.0.0.0/15


    正确答案： A
    解析： 暂无解析

  • 第13题：

    A new frame－relay network is being implemented and inverse ARP does not appear to be operating correctly. Which alternative command can be used to provide connectivity?()

    A. frame-relay arp

    B. frame-relay map

    C. frame-relay interface-dlci

    D. frame-relay lmi-type

    E. frame-relay pvc


    参考答案：B

  • 第14题：

    A new frame-relay network is being implemented and inverse ARP does not appear to be operating correctly. Which alternative command can be used to provide connectivity?（）

    • A、frame-relay arp
    • B、frame-relay map
    • C、frame-relay interface-dlci
    • D、frame-relay lmi-type
    • E、frame-relay pvc

    正确答案:B

  • 第15题：

    You are trying to bring up a new Testking location onto your existing frame relay network. The new location is using an Adtran router and you are having difficulties getting the site to connect via frame to your Cisco HQ router. What is the most likely cause of the problem?（）

    • A、Mismatched LMI types.
    • B、Incompatible encapsulation types.
    • C、Mismatching IP addresses.
    • D、Incorrect DLCI.
    • E、None of the above

    正确答案:B

  • 第16题：

    Which three statements about L2TPv3 are true？（）

    • A、L2TPv3 Frame Relay support includes only 32-bit DLCI addressing
    • B、L2TPv3 sessions do not support Frame Relay LMI interworking
    • C、Multipoint DLCI is not supported
    • D、To use DCE or a Network-to-Network Interface on a Frame Relay port， you must configure the frame-relay switching command
    • E、L2TPv3 feature does not support Frame Relay extended addressing

    正确答案:B,D,E

  • 第17题：

    Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? （）

    • A、frame-relay arp
    • B、frame-relay map
    • C、frame-relay interface-dlci
    • D、frame-relay lmi-type

    正确答案:B

  • 第18题：

    which command allows you to verify the encapsulation type CISCO OR IETF for a frame relay link?（）

    • A、show frame-relay map
    • B、show frame-relay lmi
    • C、show inter serial
    • D、show frame-relay pvc

    正确答案:C

  • 第19题：

    单选题
    Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? （）
    A

    frame-relay arp

    B

    frame-relay map

    C

    frame-relay interface-dlci

    D

    frame-relay lmi-type


    正确答案： A
    解析： 暂无解析

  • 第20题：

    多选题
    When should traffic shaping be implemented on Frame Relay PVCs？（）
    A

    When you want to drop excess traffic above the CIR

    B

    When there is a speed mismatch between the central site and the remote site

    C

    When using Frame Relay SVCs

    D

    When over-subscribing the central site link

    E

    When LLQ is implemented on the Frame Relay PVC

    F

    When Multilink PPP LFI is implemented on the Frame Relay PVC


    正确答案： A,C
    解析： 暂无解析

  • 第21题：

    单选题
    Which of the following Frame-Relay encapsulation commands would you use, if you had to connect your Cisco router to a non-Cisco router?（）
    A

    TestKRouter(config-if)# Encapsulation frame-relay dot1q

    B

    TestKRouter(config-if)# Encapsulation frame-relay aal5snap

    C

    TestKRouter(config-if)# Encapsulation frame-relay ietf

    D

    TestKRouter(config-if)# Encapsulation frame-relay isl

    E

    None of the above


    正确答案： B
    解析： 暂无解析

  • 第22题：

    单选题
    A new frame-relay network is being implemented and inverse ARP does not appear to be operating correctly. Which alternative command can be used to provide connectivity?（）
    A

    frame-relay arp

    B

    frame-relay map

    C

    frame-relay interface-dlci

    D

    frame-relay lmi-type

    E

    frame-relay pvc


    正确答案： A
    解析： 暂无解析

  • 第23题：

    单选题
    You install a new hardware router that provides wireless network connectivity between your computer and the Internet. You connect to the router by using a wireless network adapter. Your computer is able to access the Internet but is unable to discover other computers in the local wireless network.  You need to configure the wireless connection to allow your computer to discover other computers.  What should you do？（）
    A

    Configure the network category of your wireless network connection to Private.

    B

    Configure the network category of your wireless network connection to Public.

    C

    Configure the TCP/IP packet filtering on the wireless network connection.

    D

    Configure the wireless network connection with the appropriate authentication to the router.


    正确答案： A
    解析： 暂无解析

  • 第24题：

    问答题
    you want to view the status of a frame relay connection. How to display the status of a Frame-Relay PVC？

    正确答案： show frame-relay pvc and show frame-relay map
    解析： 暂无解析

相关内容