What will happen if you issue the redundancy force－switchover command on a Catalyst 6500Series Switch with redundant supervisor modules?()A. reset of the primary supervisorB. manual switchover from standby to active supervisorC. manual switchover from act

题目
What will happen if you issue the redundancy force－switchover command on a Catalyst 6500Series Switch with redundant supervisor modules?()

A. reset of the primary supervisor

B. manual switchover from standby to active supervisor

C. manual switchover from active to standby supervisor

D. automatic switchover from active to standby on primary supervisor failure

相似考题

1.Click the Exhibit button.In the exhibit, which statement is correct? ()A. Three physical interfaces are redundant.B. You must define an additional Redundancy Group.C. node 0 will immediately become primary in the cluster.D. You must issue an operational command and reboot the system for the above configuration to take effect.

2.As a network administrator, you have configured a Catalyst 6500 Series Switch with redundant supervisor engine in a CIS network. What is the result of issuing the redundancy force-switchover command on that switch?（）A. Automatic switchover from active to standby on primary supervisor failureB. Reset of the primary supervisor.C. Manual switchover from active to standby supervisorD. Manual switchover from standby to active supervisor

3.What will happen if you issue the redundancy force－switchover command on a Catalyst 6500 SeriesSwitch with redundant supervisor modules? ()A. reset of the primary supervisorB. manual switchover from standby to active supervisorC. manual switchover from active to standby supervisorD. automatic switchover from active to standby on primary supervisor failure

4.As a network administrator, you issue the interface auto qos voip cisco-phone command on a port in an edge network. It is possible for a Cisco Catalyst switch to check if a Cisco IP Phone is directly attached to that port by:（）A. using DHCP snoopingB. snooping the incoming 802.1Q VLAN tagC. using CDPD. snooping the CoS marking on the incoming frames

参考答案和解析
参考答案：C
更多“What will happen if you issue the redundancy force－switchover command on a Catalyst 6500Series Switch with redundant supervisor modules?() ”相关问题

  • 第1题：

    Which statement best describes Cisco supervisor engine redundancy using Stateful Switchover？（）

    • A、Switchover ensures that Layer 2 through Layer 4 traffic is not interrupted
    • B、Redundancy requires BGP， OSPF， EIGRP， or IS-IS
    • C、Redundancy provides fast supervisor switchover for all Cisco Catalyst 6500 series switches
    • D、Switchover can be caused by clock synchronization failure between supervisors

    正确答案:D

  • 第2题：

    Which two characteristics apply to Cisco Catalyst 6500 Series Switch supervisor redundancy  using NSF？（）

    • A、 independent of SSO
    • B、 NSF combined with SSO enables supervisor engine load balancing
    • C、 supported by RIPv2， OSPF， IS-IS， and EIGRP
    • D、 supports IPv4 and IPv6 multicast
    • E、 prevents route flapping
    • F、 dependent on FIB tables

    正确答案:E,F

  • 第3题：

    When applying the configuration in the exhibit and initializing a chassis cluster， which statement is correct？（） [edit chassis] user@host# show cluster { reth-count 3； redundancy-group 1 { node 0 priority 1； node 1 priority 100； } }

    • A、Three physical interfaces are redundant.
    • B、You must define an additional redundancy group.
    • C、node 0 will immediately become primary for redundancy group 1.
    • D、You must issue an operational command and reboot the system for the above configuration to take effect.

    正确答案:D

  • 第4题：

    What will happen if you issue the redundancy force-switchover command on a Catalyst 6500Series Switch with redundant supervisor modules?（）

    • A、reset of the primary supervisor
    • B、manual switchover from standby to active supervisor
    • C、manual switchover from active to standby supervisor
    • D、automatic switchover from active to standby on primary supervisor failure

    正确答案:C

  • 第5题：

    As a network administrator, you issue the interface auto qos voip cisco-phone command on a port in an edge network. It is possible for a Cisco Catalyst switch to check if a Cisco IP Phone is directly attached to that port by:（）

    • A、using DHCP snooping
    • B、snooping the incoming 802.1Q VLAN tag
    • C、using CDP
    • D、snooping the CoS marking on the incoming frames

    正确答案:C

  • 第6题：

    What are two results of entering the Switch(config)# vtp mode client command on a Catalyst switch?（）

    • A、The switch will ignore VTP summary advertisements
    • B、The switch will forward VTP summary advertisements
    • C、The switch will process VTP summary advertisements
    • D、The switch will originate VTP summary advertisements
    • E、The switch will create, modify and delete VLANs for the entire VTP domain

    正确答案:B,C

  • 第7题：

    单选题
    You have enabled backup optimization in RMAN. You issue the following RMAN command to configure a redundancy-based retention policy：   CONFIGURE RETENTION POLICY TO REDUNDANCY 3；   Which statement is true？（）
    A

     The command fails because you cannot configure a redundancy-based retention policy when backup  optimization is enabled

    B

     Backup optimization is performed， but RMAN considers the redundancy-based retention policy when it determines which datafiles should be backed up

    C

     Backup optimization is permanently disabled

    D

     Backup optimization is temporarily disabled because a redundancy-based retention policy is specified


    正确答案： D
    解析： 暂无解析

  • 第8题：

    多选题
    Which two characteristics apply to Cisco Catalyst 6500 Series Switch supervisor redundancy  using NSF？（）
    A

    independent of SSO

    B

    NSF combined with SSO enables supervisor engine load balancing

    C

    supported by RIPv2， OSPF， IS-IS， and EIGRP

    D

    supports IPv4 and IPv6 multicast

    E

    prevents route flapping

    F

    dependent on FIB tables


    正确答案： A,F
    解析： 暂无解析

  • 第9题：

    单选题
    You need to troubleshoot an issue on the switched LAN. When you issue a command "show port3/1" on a switch， you observe the Giants column has a non-zero entry. What could cause this？（）
    A

    IEEE 802.10

    B

    Misconfigured NIC

    C

    User configuration

    D

    IEEE 802.1Q

    E

    None of the other alternatives apply


    正确答案： B
    解析： 暂无解析

  • 第10题：

    单选题
    As a network administrator, you have configured a Catalyst 6500 Series Switch with redundant supervisor engine in a CIS network. What is the result of issuing the redundancy force-switchover command on that switch?（）
    A

    Automatic switchover from active to standby on primary supervisor failure

    B

    Reset of the primary supervisor.

    C

    Manual switchover from active to standby supervisor

    D

    Manual switchover from standby to active supervisor


    正确答案： D
    解析： 暂无解析

  • 第11题：

    单选题
    What will happen if you issue the redundancy force-switchover command on a Catalyst 6500 SeriesSwitch with redundant supervisor modules? （）
    A

    reset of the primary supervisor

    B

    manual switchover from standby to active supervisor

    C

    manual switchover from active to standby supervisor

    D

    automatic switchover from active to standby on primary supervisor failure


    正确答案： D
    解析： 暂无解析

  • 第12题：

    单选题
    Click the Exhibit button. In the exhibit, which statement is correct? （）
    A

    Three physical interfaces are redundant.

    B

    You must define an additional Redundancy Group.

    C

    node 0 will immediately become primary in the cluster.

    D

    You must issue an operational command and reboot the system for the above configuration to take effect.


    正确答案： B
    解析： 暂无解析

  • 第13题：

    You need to troubleshoot an issue on the switched LAN. When you issue a command "show port3/1" on a switch， you observe the Giants column has a non-zero entry. What could cause this？（）

    • A、IEEE 802.10
    • B、Misconfigured NIC
    • C、User configuration
    • D、IEEE 802.1Q
    • E、None of the other alternatives apply

    正确答案:D

  • 第14题：

    You are at a client site. It is a medium-sized business and needs a Cisco Catalyst switch that offers high availability and security. What type of Catalyst switches would you recommend？（）

    • A、 Catalyst 2960 Series
    • B、 Catalyst 3750 Series
    • C、 Catalyst 4900 Series
    • D、 Catalyst 6500 Series

    正确答案:A

  • 第15题：

    What are two results of entering the Switch(config)# vtp mode client command on a Catalyst switch?（）

    • A、The switch will ignore VTP summary advertisements.
    • B、The switch will forward VTP summary advertisements.
    • C、The switch will process VTP summary advertisements.
    • D、The switch will originate VTP summary advertisements.
    • E、The switch will create, modify and delete VLANs for the entire VTP domain.

    正确答案:B,C

  • 第16题：

    Company has a Catalyst 6500 and you need to configure redundancy between the supervisormodules. With route processor redundancy （RPR+）， the redundant supervisor engine is fullyinitialized and configured， which shortens the switchover time if the active supervisor engine fails.Which three statements are true about the RPR + operations when the redundant supervisorengine switched over the failed primary supervisor engine？（）

    • A、Static IP routes are maintained across a switchover because they are configured from entries inthe configuration file
    • B、Information about dynamic routing states， maintained on the active supervisor engine， issynchronized to the redundant supervisor engine and is transferred during the switchover
    • C、Information about dynamic routing states， maintained on the active supervisor engine， is notsynchronized to the redundant supervisor engine and is lost on switchover
    • D、The Forwarding Information Base （FIB） tables are cleared on a switchover. As a result， routedtraffic is interrupted until route tables reconverge
    • E、Static IP routes are cleared across a switchover and recreated from entries in the configurationfile on the redundant supervisor engine
    • F、The Forwarding Information Base （FIB） tables are maintained during the switchover. As aresult， routed traffic continues without any interruption when the failover occurs

    正确答案:A,C,D

  • 第17题：

    How many access points will a Cisco 7600 Series Router with six installed Cisco Catalyst 6500Series Wireless Services Modules support？（）

    • A、300
    • B、448
    • C、664
    • D、1800
    • E、2400

    正确答案:D

  • 第18题：

    单选题
    You have enabled backup optimization in RMAN. You issue the following RMAN command to configure a redundancy-based retention policy: CONFIGURE RETENTION POLICY TO REDUNDANCY 3; Which statement is true?（）
    A

    The command fails because you cannot configure a redundancy-based retention policy when backup optimization is enabled

    B

    Backup optimization is performed, but RMAN considers the redundancy-based retention policy when it determines which datafiles should be backed up

    C

    Backup optimization is permanently disabled

    D

    Backup optimization is temporarily disabled because a redundancy-based retention policy is specified


    正确答案： D
    解析： 暂无解析

  • 第19题：

    单选题
    A manufacturing customer has an IBM BladeCenter H chassis with four， HX5 with MAX5 4-socket blades installed. Each blade has the optional Fibre Channel Expansion card. The customer wants redundancy and is going to install the following configuration：  （1）two Brocade 20-Port SAN Switch Modules  （2）two Nortel Networks 1/10 GB Uplink ESM  （3）a redundant AMM  What is the minimum number of power supplies needed for this configuration to have full redundancy？（）
    A

    4

    B

    3

    C

    2

    D

    8


    正确答案： B
    解析： 暂无解析

  • 第20题：

    多选题
    What are two results of entering the Switch(config)# vtp mode client command on a Catalyst switch?（）
    A

    The switch will ignore VTP summary advertisements

    B

    The switch will forward VTP summary advertisements

    C

    The switch will process VTP summary advertisements

    D

    The switch will originate VTP summary advertisements

    E

    The switch will create, modify and delete VLANs for the entire VTP domain


    正确答案： B,E
    解析： 暂无解析

  • 第21题：

    多选题
    pany has a Catalyst 6500 and you need to configure redundancy between the supervisor  modules. With route processor redundancy （RPR+）， the redundant supervisor engine is fully initialized and configured， which shortens the switchover time if the active supervisor engine fails.   Which three statements are true about the RPR + operations when the redundant supervisor  engine switched over the failed primary supervisor engine？ （）
    A

    Static IP routes are maintained across a switchover because they are configured from entries in  the configuration file.

    B

    Information about dynamic routing states， maintained on the active supervisor engine， is  synchronized to the redundant supervisor engine and is transferred during the switchover.

    C

    Information about dynamic routing states， maintained on the active supervisor engine， is not  synchronized to the redundant supervisor engine and is lost on switchover.

    D

    The Forwarding Information Base （FIB） tables are cleared on a switchover. As a result， routed  traffic is interrupted until route tables reconverge.

    E

    Static IP routes are cleared across a switchover and recreated from entries in the configuration  file on the redundant supervisor engine.

    F

    The Forwarding Information Base （FIB） tables are maintained during the switchover. As a  result， routed traffic continues without any interruption when the failover occurs.


    正确答案： B,E
    解析： 暂无解析

  • 第22题：

    单选题
    You are at a client site. It is a medium-sized business and needs a Cisco Catalyst switch that offers high availability and security. What type of Catalyst switches would you recommend？（）
    A

     Catalyst 2960 Series

    B

     Catalyst 3750 Series

    C

     Catalyst 4900 Series

    D

     Catalyst 6500 Series


    正确答案： A
    解析： 暂无解析

  • 第23题：

    单选题
    If you issue the command shutdown abort prior to trying to put the database in ARCHIVELOG mode， what will be the result when you issue the command alter database archivelog？（）
    A

     The alter database archivelog command will fail

    B

     The alter database archivelog inconsistent command must be used to put the database in ARCHIVELOG mode

    C

     The alter database archivelog command will succeed

    D

     The alter database archivelog command will ask if you want to make the database consistent first

    E

     There is no alter database archivelog command. The correct command is alter database alterlogging


    正确答案： D
    解析： 暂无解析

相关内容