Refer to the exhibit. The partial configuration for an OSPF ASBR and an Area 0 ABR is shown. Assume the OSPF configurations throughout the network are operable. Which statement about these configurations is true? ()
A. The ASBR route - maps are basically useless, because there are no deny prefix - lists.
B. LSA Type 5s wil l not be received by the ABR from the ASBR.
C. The OSPF backbone will not learn any RFC 1918 addresses.
D. The matched prefix - list addresses will be given a metric of 255, which is essentially unreachable.
第1题:
Refer to the exhibit. Router C was configured so that it could form an adja cency with three OSPF neighbors, one connected to each of its three physical interfaces. Which statement is correct about router C?()
A. It is configured and functioning correctly as an OSPF internal router.
B. It is configured and functioning correc tly as an ABR attached to stub area 4.
C. It is configured and functioning correctly as an ASBR attached to external area 4.
D. It is configured and functioning correctly as an ABR attached to totally stubby area 4.
E. It is not configured correctly to function as specified.
第2题:
A. 10.10.10.16/28 only
B. 10.10.10.16/28 and 10.10.10.64/26
C. 10.10.10.16/28, 10.10.10.64/26, and 172.16.10.0/24
D. 10.10.10.64/26 only
第3题:
Refer to the exhibit. A network administrator wants to reduce the number of OSPF routes advertised from Area 1 into Area 2. As the router configuration specialist, what two things would you do to accomplish this goal?()
A. Enter the configuration on router B1.
B. Enter the configuration on router B4.
C. On the same router, enter the Summary - address 10.10.1.0 255.255.255.128 subcommand.
D. On the same router, enter the Area 1 range 10.10.1.0 255.255.255.128 subcommand.
E. On the same ro uter, enter the Area 2 range 10.10.1.0 255.255.255.128 subcommand.
第4题:
A. This is the designated router (DR) on the FastEthernet 0/0 link.
B. The output was generated by the show ip interface c ommand.
C. The router was configured with the commands:r outer ospf 1 network 172.16.6.0 0.0.0.255 area 1
D. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.
E. Interface FastEthernet 0/0 was configured with the ipv6 o spf 1 area 1 command.
F. OSPF version 2 has been enabled to support IPv6.
第5题:
A. On the ABR router ospf 10 area 3 stub
B. On all Area 3 routers router ospf 10 area 3 stub
C. On all Area 3 routers router ospf 10 area 3 stub no - summary
D. On the ABR router ospf 10 area 3 nssa
E. On the ABR rou ter ospf 10 area 3 stub no - summary
第6题:
A.通过ABR之间直接
B.通过ASBR之间
C.通过0号area
D.通过1号area
第7题:
Which of the following is an OSPF configuration parameter that is used on an ABR, but not on an internal router?()
第8题:
You have a multi-area OSPF network and you’re concerned because one of the sites is havingconnectivity problem to resources in a different area. Which IOS privileged mode command wouldyou enter to confirm that your network: (A) has a path to its ABR, (B) has a path to its ASBR, and (C)the SPF calculation is functional?()
第9题:
OSPF动态路由协议中,不同area之间的路由()传播来避免路由环路出现。
第10题:
Generated by the ASBR and describes reachability to itself
Generated by the ASBR and describes reachabilty to the ABR
Generated by the ABR and describes reachabilty to the ASBR for routers in a different area from the ASBR
Generated by the ABR and describes reachabilty to the ASBR for routers in the same area with the ASBR
第11题:
CEF was not properly configured.
OSPF was not properly configured for graceful restart.
Stateful switchover was not correctly configured.
NSF for OSPF is only supported in area 0.
第12题:
A virtual link to area 0.
OSPF summarization command.
default - cost extension to the area command.
no - summary extension to the area stub comm and.
None of the other alternatives apply
第13题:
A. All interfaces will be in area 0
B. The router will be an ABR with s1/0 in area 0 and f0/0 and 0/1 in area 1
C. The route r will be an ABR with s1/0 in area 0 and f0/0 and 0/1 in area 2
D. The router will be an ABR with s1/0 in area 0, f0/0 in area 1, and f0/1 in area 2
第14题:
A. 10.10.10.16/28 only
B. 10.10.10.16/28 and 10.10.10.64/26
C. 10.10.10.16/28, 10.10.10 .64/26, and 172.16.10.0/24
D. 10.10.10.64/26 only
第15题:
A.The NProuter has two OSPF neighbors in the "Full" adjacency state
B.The NProuter serial0/0 interface has the OSPF dead timer set to 10 seconds
C.The NProuter serial0/0 interface has been configured with an OSPF network type of "pointtopoint"
D.The 10.1.1.1 and 10.1.1.2 routers are not using the default OSPF dead and hello timers setting
E.The "Mismatched" error is caus ed by the expiration of the OSPF timers
第16题:
A. A virtual link to area 0.
B. OSPF summarization command.
C. default - cost extension to the area command.
D. no - summary extension to the area stub comm and.
E. None of the other alternatives apply
第17题:
Refer to the exhibit. A network associate has configured OSPF with the command:City(config-router) network 192.168.12.64 0.0.0.63 area 0After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? ()
A.FastEthernet0 /0
B.FastEthernet0 /1
C.Serial0/0
D.Serial0/1.102
E.Serial0/1.103
F.Serial0/1.104
第18题:
Which statement about OSPF ASBR summary LSA is true?()
第19题:
在OSPF中,关于ABR和ASBR论述正确的有()。
第20题:
Cat6500(config)# router ospf 1 Cat6500(config-router)# network 0.0.0.0 255.255.255.255 area 0 Cat6500(config-router)# nsf Cat6500(config-router)#end Refer to the exhibit. The configuration is used to enable nonstop forwarding for OSPF on a Catalyst 6500 Series Switch with redundant supervisor engines. The default CEF configuration is unchanged. After testing, user traffic is interrupted and NSF is not operational. What is the most likely reason? ()
第21题:
通过ABR之间直接
通过ASBR之间
通过0号area
通过1号area
第22题:
It is generated by an ASBR and indicates the reachability to an ABR located in another area.
It is generated by ABR and indicates the reachability to an ASBR located in another AS.
It is generated by ABR and indicates reachability to itself.
It is generated by ABR and indicates the reachability to an ASBR located in another area.
It is generated by ASBR and indicates the reachability to an ABR.
第23题:
Apply the area 4 stub command to all routers in the area
On the ABR, use the area 4 stub command with the no - summary keyword
On the ABR, specify a default cost for the area with the area default - cost command
On the ABR, use the default - information originate command to inject a default route into area 4
Use the auto - cost command on each router in the area to automatically determine the cost to other OSPF areas