What is the default maximum number of equal-cost paths that can be placed into the routing of a cisco OSPF router?（）A、16B、2C、unlimitedD、4

题目

What is the default maximum number of equal-cost paths that can be placed into the routing of a cisco OSPF router?（）

  • A、16
  • B、2
  • C、unlimited
  • D、4
相似考题

1.What is the maximum number of equal－cost paths that can be configured for RIP on an ERX Edge Router?()A.4B.8C.12D.16

2.OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterAping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A.What can you conclude about router A?（）A. Only the router A loopback interface is parti cipating in the OSPF routing processB. None of the router A interfaces are participating in the OSPF routing processC. Router A is using the loopback interface IP address as its OSPF router IDD. Router A does not have any reachable OSPF neighbors

3.What are the characteristic of link state routing protocols?()A. The exchange of advertisement is triggered by a change in the network.B. All routers exchange routing tables with each other iIn a multipoint network.C. Packets are routed based upon the shortest path to the destination.D. Paths are chosen depending on the cost efficiency factor.E. Every router in an OSPF area is capable of representing the entire network topology.F. Only the designated router in an OSPF area can represent the entire network topology.

4.Refer to the exhibit. Router B and router C are performing mutual redistribution between OSPF and EIGRP, and their default metrics are configured the same. Router D has equal cost paths to networks where both paths are not r eally equal cost. For example, network 172.16.54.0 shows equal cost through both router B and router C, though in reality the cost is greater using router C. Other routers, though not shown, are connected to the 172.16.54.0 and 172.16.55.0 networks, and the same issues exist to those routers and the networks connected to them. What can be done so that data will be routed along the most optimal path in the network? （）A. Redistribute connected interfaces on router B and router CB. Set the maximum nu mber of equal cost paths to1 in all routersC. When redistributing EIGRP into OSPF, set the external metric type to type E1D. Adjust the default metrics in router B and router C so that the values are different in each routerE. None of these solut ions will fix the problem. Migrate to a single dynamic routing protocol

参考答案和解析
正确答案:D
更多“What is the default maximum number of equal-cost paths that can be placed into the routing of a cisco OSPF router?（）A、16B、2C、unlimitedD、4”相关问题

  • 第1题：

    What is the default maximum number of equal－cost paths that can be placed into the routing of a cisco OSPF router?()

    A. 16

    B. 2

    C. unlimited

    D. 4


    参考答案：D

  • 第2题：

    How will router A choose a path to the 10.1.2.0／24 network when different routing protocols are configured (Choose three.)()。

    A.If RIPv2 is the routing protocol, only the path AD will be installed in the routing table by default.

    B.If RIPv2 is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.

    C.If EIGRP is the routing protocol, only the path AD will be installed in the routing table by default.

    D.If EIGRP is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.

    E.If EIGRP and OSPF are both running on the network, the EIGRP paths will be installed in the routing table.

    F.If EIGRP and OSPF are both running on the network, the OSPF paths will be installed in the routing table.


    参考答案：A, D, E

  • 第3题：

    What is the OSPF default frequency,in seconds,at which a cisco router sends hello packets on a multiaccess network?（）

    • A、10
    • B、40
    • C、30
    • D、20

    正确答案:A

  • 第4题：

    What is the maximum number of network locales that can be configured for any one Cisco Unified CallManager Express when using the cnf-file perphone command?（）

    • A、1 
    • B、2 
    • C、4 
    • D、5
    • E、a number equal to the number of languages supported by Cisco Unity Express 
    • F、a number equal to the number of languages supported by Cisco Unity CallManager Express

    正确答案:D

  • 第5题：

    Which command would display OSPF parameters such as filters，default metric，maximum paths，and number of areas configured on a outer（）

    • A、show ip protocol
    • B、show ip route
    • C、show ip ospfinterface
    • D、show ip ospf
    • E、show ip nterface
    • F、None of the other alternatives apply

    正确答案:A

  • 第6题：

    What is the default maximum number of equal-cost paths that can be placed into the routing of a cisco OSPF router?（）

    • A、16
    • B、2
    • C、unlimited
    • D、4

    正确答案:D

  • 第7题：

    What is the maximum number of hexadecimal characters allowed when configuring the WPA or WPA2passphrase in Cisco ADU？（）

    • A、16
    • B、32
    • C、64
    • D、128

    正确答案:C

  • 第8题：

    What is the maximum number of nodes that can be configured in a single PowerHA cluster？（）

    • A、16
    • B、32
    • C、64
    • D、128

    正确答案:B

  • 第9题：

    单选题
    What is the OSPF default frequency,in seconds,at which a cisco router sends hello packets on a multiaccess network?（）
    A

    10

    B

    40

    C

    30

    D

    20


    正确答案： D
    解析： 暂无解析

  • 第10题：

    单选题
    What is the maximum number of equal-cost paths that can be configured for RIP on an ERX Edge Router?（）
    A

    4

    B

    8

    C

    12

    D

    16


    正确答案： B
    解析： 暂无解析

  • 第11题：

    多选题
    How will router A choose a path to the 10.1.2.0/24 network when different routing protocols are configured (Choose three.)（）。
    A

    If RIPv2 is the routing protocol, only the path AD will be installed in the routing table by default.

    B

    If RIPv2 is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.

    C

    If EIGRP is the routing protocol, only the path AD will be installed in the routing table by default.

    D

    If EIGRP is the routing protocol, the equal cost paths ABD and ACD will be installed in the routing table by default.

    E

    If EIGRP and OSPF are both running on the network, the EIGRP paths will be installed in the routing table.

    F

    If EIGRP and OSPF are both running on the network, the OSPF paths will be installed in the routing table.


    正确答案： A,D
    解析： 暂无解析

  • 第12题：

    单选题
    Which command would display OSPF parameters such as filters， default metric， maximum paths，and number of areas configured on a router？（）
    A

    show ip protocol

    B

    show ip route

    C

    show ip ospf interface

    D

    show ip ospf

    E

    show ip interface

    F

    None of the other alternatives apply


    正确答案： E
    解析： 暂无解析

  • 第13题：

    What is the OSPF default frequency,in seconds,at which a cisco router sends hello packets on a multiaccess network?()

    A.10

    B.40

    C.30

    D.20


    参考答案：A

  • 第14题：

    What is the maximum number of Cisco Catalyst 3750 Series Switches that can be united into a single manageable unit using the Cisco StackWise technology?（）

    • A、9
    • B、3
    • C、12
    • D、6

    正确答案:A

  • 第15题：

    When building a NIC team （virtual port channel） between a host and a pair of Cisco Nexus 5000 Series Switches that will carry FCoE traffic， what is the maximum number of physical links that can exist in the team？（）

    • A、 1
    • B、 2
    • C、 4
    • D、 5
    • E、 16

    正确答案:B

  • 第16题：

    What is the maximum number of equal-cost paths that can be configured for RIP on an ERX Edge Router?（）

    • A、4
    • B、8
    • C、12
    • D、16

    正确答案:D

  • 第17题：

    Which three factors have the biggest influence on OSPF scalability？（）

    • A、Flooding paths and redundancy
    • B、Amount of routing information in the OSPF area or routing domain
    • C、Number of routers with Cisco Express Forwarding enabled
    • D、Number of neighbor adjacencies
    • E、Other routing protocols in use
    • F、OSPF timer reconstruction negotiation
    • G、Redistribution with BGP neighbors
    • H、Redistribution with other IGP routing protocols， such as RIP or EIGRP

    正确答案:A,B,D

  • 第18题：

    Which command would display OSPF parameters such as filters， default metric， maximum paths，and number of areas configured on a router？（）

    • A、show ip protocol
    • B、show ip route
    • C、show ip ospf interface
    • D、show ip ospf
    • E、show ip interface
    • F、None of the other alternatives apply

    正确答案:A

  • 第19题：

    What is the default maximum transmission unit on the Cisco router ATM interface？（）

    • A、4470 bytes
    • B、1516 bytes
    • C、9288 bytes
    • D、1500 bytes
    • E、1492 bytes

    正确答案:E

  • 第20题：

    单选题
    What is the default maximum number of equal-cost paths that can be placed into the routing of a cisco OSPF router?（）
    A

    16

    B

    2

    C

    unlimited

    D

    4


    正确答案： A
    解析： 暂无解析

  • 第21题：

    单选题
    What is the maximum number of network locales that can be configured for any one Cisco Unified CallManager Express when using the cnf-file perphone command?（）
    A

    1 

    B

    2 

    C

    4 

    D

    5

    E

    a number equal to the number of languages supported by Cisco Unity Express 

    F

    a number equal to the number of languages supported by Cisco Unity CallManager Express


    正确答案： D
    解析： 暂无解析

  • 第22题：

    单选题
    When building a NIC team （virtual port channel） between a host and a pair of Cisco Nexus 5000 Series Switches that will carry FCoE traffic， what is the maximum number of physical links that can exist in the team？（）
    A

     1

    B

     2

    C

     4

    D

     5

    E

     16


    正确答案： D
    解析： 暂无解析

  • 第23题：

    单选题
    OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterA#ping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A. What can you conclude about router A?（）
    A

    Only the router A loopback interface is parti cipating in the OSPF routing process

    B

    None of the router A interfaces are participating in the OSPF routing process

    C

    Router A is using the loopback interface IP address as its OSPF router ID

    D

    Router A does not have any reachable OSPF neighbors


    正确答案： D
    解析： 暂无解析

  • 第24题：

    单选题
    Which command would display OSPF parameters such as filters，default metric，maximum paths，and number of areas configured on a outer（）
    A

    show ip protocol

    B

    show ip route

    C

    show ip ospfinterface

    D

    show ip ospf

    E

    show ip nterface

    F

    None of the other alternatives apply


    正确答案： B
    解析： 暂无解析

相关内容