A Ezonexam router boots up in ROMMON mode. What is ROM Monitor (ROMMON)?A. A memory component for storing the saved configuration fileB. A memory management toolC. An operating system used for hardware troubleshooting and for password recoveryD. Temporary

题目

A Ezonexam router boots up in ROMMON mode. What is ROM Monitor (ROMMON)?

A. A memory component for storing the saved configuration file

B. A memory management tool

C. An operating system used for hardware troubleshooting and for password recovery

D. Temporary storage space for the router operating files

E. The source of the primary Cisco IOS software image

F. None of the above

相似考题

1.You are a senior network administrator at Ezonexam, and while performing the password recovery procedure on your 2500 series Cisco router, you type in the following command:o/r 0x2142What is the purpose of this command?A．It is used to restart the router.B．It is used to bypass the configuration in NVRAM.C．It is used to enter ROM Monitor mode.D．It is used to view the lost password.E．It is used to save the changes to the configuration.

2.During the boot sequence, a Ezonexam 2800 series router needs to locate and load an operating system. What is the default order the router uses to find an operating system?A．ROM, TFTP server, FlashB．Flash, TFTP server, ROMC．Flash, NVRAM, TFTP serverD．Flash, ROM, TFTP serverE．Flash, TFTP server, RAM

3.What is the purpose of typing o／r 0x2142 during a password recover procedure on a 2500 series router?()A. To restart the router.B. To bypass the configuration in NVRAM.C. To view the lost password.D. To save the changes to the configuration.E. To enter ROM Monitor mode.

4.An administrator is adding memory to a server. Once the system boots up, the same amount of memory appears as before the upgrade. Which of the following is the MOST likely cause?()A. The memory is not the correct CAS latency.B. The memory is not installed in the correct slot.C. The memory does not have the correct timing.D. The memory is not the correct speed.

更多“A Ezonexam router boots up in ROMMON mode. What is ROM Monitor (ROMMON)?A. A memory component for storing the saved configuration fileB. A memory management toolC. An operating system used for hardware troubleshooting and for password recoveryD. Temporary”相关问题

  • 第1题：

    After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode.What is the most likely cause of this?（）

    A. The NVRAM is corrupted.

    B. The boot system commands were omitted in the configuration.

    C. The configuration register setting is incorrect.

    D. The upgraded configuration incompatible with the hardware platform.

    E. The upgraded IOS incompatible with the hardware.


    参考答案：C

  • 第2题：

    A network administrator changes the configuration register to 0x2142 and reboots the router. What are two results of making this change?()

    A. The IOS image will be ignored.

    B. The router will prompt to enter initial configuration mode.

    C. The router will boot to ROM.

    D. Any configuration entries in NVRAM will be ignored.

    E. The configuration in flash memory will be booted.


    参考答案：B, D

  • 第3题：

    You are a senior network administrator at TestKing, and while performing thepassword recovery procedure on your 2500 series Cisco router, you type in thefollowing command:o/r 0x2142What is the purpose of this command?（）

    • A、It is used to restart the router.
    • B、It is used to bypass the configuration in NVRAM.
    • C、It is used to enter ROM Monitor mode.
    • D、It is used to view the lost password.
    • E、It is used to save the changes to the configuration.

    正确答案:B

  • 第4题：

    A network administrator changes the configuration register to 0x2142 and reboots the router. What are two results of making this change?（）

    • A、The IOS image will be ignored.
    • B、The router will prompt to enter initial configuration mode.
    • C、The router will boot to ROM.
    • D、Any configuration entries in NVRAM will be ignored.
    • E、The configuration in flash memory will be booted.

    正确答案:B,D

  • 第5题：

    A characteristic of operating system is（）。

    • A、 resource  management 
    • B、 memory management 
    • C、 error recovery 
    • D、 all the above

    正确答案:A

  • 第6题：

    What is the purpose of typing o/r 0x2142 during a password recover procedure on a 2500 series router?（）

    • A、To restart the router.
    • B、To bypass the configuration in NVRAM.
    • C、To view the lost password.
    • D、To save the changes to the configuration.
    • E、To enter ROM Monitor mode.

    正确答案:B

  • 第7题：

    An administrator is adding memory to a server. Once the system boots up， the same amount of memory appears as before the upgrade. Which of the following is the MOST likely cause？（）

    • A、The memory is not the correct CAS latency.
    • B、The memory is not installed in the correct slot.
    • C、The memory does not have the correct timing.
    • D、The memory is not the correct speed.

    正确答案:B

  • 第8题：

    Your database is configured in shared server mode. However， your senior DBA asks you to modify the value ofthe PRIVATE_SGA limit in the profile of the users.  What could be the reason for this（）

    • A、To limit the User Global Area （UGA） memory allocated to a session from the SGA
    • B、To limit the amount of memory to be used for the dispatcher queue of a session in SGA
    • C、To limit the amount of memory to be used for the request pool in System Global Area （SGA）
    • D、To control the amount of memory allocated in SGA for the local variables for each shared server process

    正确答案:A

  • 第9题：

    单选题
    After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode. What is the most likely cause of this?（）
    A

    The NVRAM is corrupted.

    B

    The boot system commands were omitted in the configuration.

    C

    The configuration register setting is incorrect.

    D

    The upgraded configuration incompatible with the hardware platform.

    E

    The upgraded IOS incompatible with the hardware.


    正确答案： D
    解析： 暂无解析

  • 第10题：

    单选题
    What is the purpose of typing o/r 0x2142 during a password recover procedure on a 2500 series router?（）
    A

    To restart the router.

    B

    To bypass the configuration in NVRAM.

    C

    To view the lost password.

    D

    To save the changes to the configuration.

    E

    To enter ROM Monitor mode.


    正确答案： B
    解析： 暂无解析

  • 第11题：

    单选题
    An administrator is adding memory to a server. Once the system boots up， the same amount of memory appears as before the upgrade. Which of the following is the MOST likely cause？（）
    A

     The memory is not the correct CAS latency.

    B

     The memory is not installed in the correct slot.

    C

     The memory does not have the correct timing.

    D

     The memory is not the correct speed.


    正确答案： C
    解析： 暂无解析

  • 第12题：

    单选题
    An administrator is adding memory to a server. Once the system boots up, the same amount of memory appears as before the upgrade. Which of the following is the MOST likely cause?（）
    A

    The memory is not the correct CAS latency.

    B

    The memory is not installed in the correct slot.

    C

    The memory does not have the correct timing.

    D

    The memory is not the correct speed.


    正确答案： D
    解析： 暂无解析

  • 第13题：

    You are a senior network administrator at TestKing, and while performing thepassword recovery procedure on your 2500 series Cisco router, you type in thefollowing command:o/r 0x2142What is the purpose of this command?（）

    A. It is used to restart the router.

    B. It is used to bypass the configuration in NVRAM.

    C. It is used to enter ROM Monitor mode.

    D. It is used to view the lost password.

    E. It is used to save the changes to the configuration.


    参考答案：B

  • 第14题：

    Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? ()

    A.Router1 has specific boot system command that instruct it to load IOS from TFTP server.

    B.Router1 is acting as a TFTP server for other routers.

    C.Router1 cannot locate a valid IOS image in flash memory.

    D.Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.

    E.Cisco routers will first attempt to load a image from TFTP for management purposes.


    参考答案：A, C

  • 第15题：

    What is the purpose of pressing the Ctrl+Break keys during the router password recover procedure?（）

    • A、To restart the router.
    • B、To bypass the configuration in Flash.
    • C、To view the password before changes are made.
    • D、To bypass setup configuration mode.
    • E、To access ROM Monitor mode.

    正确答案:E

  • 第16题：

    After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode. What is the most likely cause of this?（）

    • A、The NVRAM is corrupted.
    • B、The boot system commands were omitted in the configuration.
    • C、The configuration register setting is incorrect.
    • D、The upgraded configuration incompatible with the hardware platform.
    • E、The upgraded IOS incompatible with the hardware.

    正确答案:C

  • 第17题：

    What will be disabled as a result of the no service password-recovery command？（）

    • A、password encryption service
    • B、changes to the config-register setting
    • C、the xmodem privilege EXEC mode command to recover the Cisco IOS image
    • D、ROMMON

    正确答案:D

  • 第18题：

    Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? （）

    • A、Router1 has specific boot system command that instruct it to load IOS from TFTP server.
    • B、Router1 is acting as a TFTP server for other routers.
    • C、Router1 cannot locate a valid IOS image in flash memory.
    • D、Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.
    • E、Cisco routers will first attempt to load a image from TFTP for management purposes.

    正确答案:A,C

  • 第19题：

    A customer has asked for a p690 system with the following requirements：   ？ 32 1.9ghz processors   ？ 128GB of memory   ？ 20 fiber adapters   ？ 7 network cards   ？ 10 LPARs   What is the most appropriate question to ask them in order to build the hardware configuration correctly？（）

    • A、What version of AIX is needed？
    • B、Which SWMA offering is needed？
    • C、What kind of network is the system being attached to？
    • D、What kind of memory should be configured on the system？

    正确答案:C

  • 第20题：

    单选题
    You are a senior network administrator at TestKing, and while performing thepassword recovery procedure on your 2500 series Cisco router, you type in thefollowing command:o/r 0x2142What is the purpose of this command?（）
    A

    It is used to restart the router.

    B

    It is used to bypass the configuration in NVRAM.

    C

    It is used to enter ROM Monitor mode.

    D

    It is used to view the lost password.

    E

    It is used to save the changes to the configuration.


    正确答案： B
    解析： 暂无解析

  • 第21题：

    多选题
    Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? （）
    A

    Router1 has specific boot system command that instruct it to load IOS from TFTP server.

    B

    Router1 is acting as a TFTP server for other routers.

    C

    Router1 cannot locate a valid IOS image in flash memory.

    D

    Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.

    E

    Cisco routers will first attempt to load a image from TFTP for management purposes.


    正确答案： A,C
    解析： 暂无解析

  • 第22题：

    多选题
    A network administrator changes the configuration register to 0x2142 and reboots the router. What are two results of making this change?（）
    A

    The IOS image will be ignored.

    B

    The router will prompt to enter initial configuration mode.

    C

    The router will boot to ROM.

    D

    Any configuration entries in NVRAM will be ignored.

    E

    The configuration in flash memory will be booted.


    正确答案： A,D
    解析： 暂无解析

  • 第23题：

    单选题
    What is the purpose of pressing the Ctrl+Break keys during the router password recover procedure?（）
    A

    To restart the router.

    B

    To bypass the configuration in Flash.

    C

    To view the password before changes are made.

    D

    To bypass setup configuration mode.

    E

    To access ROM Monitor mode.


    正确答案： B
    解析： 暂无解析

相关内容