Which RIP configuration command allows the ERX Edge Router to send Unicast updates to configured neighbors?()A.neighborB.unicast-neighborC.triggered-updateD.passive-interface

题目
Which RIP configuration command allows the ERX Edge Router to send Unicast updates to configured neighbors?()

A.neighbor

B.unicast-neighbor

C.triggered-update

D.passive-interface

相似考题

1.在Cisco路由器上配置RIPvl路由协议，参与RIP路由的网络地址有193.22.56.0/26、193.22.56.64/26、193.22.56.128/26和193.22.56.192/26，正确的配置命令是( )。A) Router(config)# netword 193.22.56.0 0.0.0.255B) Router(config-router)# netword 193.22.56.0 255.255.255.0C) Router(config)# netword 193.22.56.0D) Router(config-router)# netword 193.22.56.0

2.阅读以下说明，回答问题1、问题2、问题3和问题4，将解答填入对应栏内。[说明]RIP(Routing Information Protocols，路由信息协议)是使用最广泛的距离向量协议，它是由施乐(Xerox)在70年代开发的。当时，RIP是XNS(Xerox Network Service，施乐网络服务)协议簇的一部分。TCP/IP版本的RIP是施乐协议的改进版。RIP最大的特点是无论实现原理还是配置方法，都非常简单。以下是RIP配置的部分清单。Router＞enable (1)Enter configuration commands，one per line．End with CNTL/Z． (2)Router (config) interfacee 0/1 (3)Router (config-if) ipaddress172.16.1.2 255.255.255.0Router (config-if)//为了便于配置和记忆，还可以给每个端口添加一些描述信息。如下所示，在端口局部配置模式下使用description命令。Router ( config-if ) description connect to CIU (8)Router (config-if) endRouter......Routercopy mnning-config startup-config (12)Building configuration...[OK]Router......Router (config) linc console 0 (17)Router (config-line) login (18)Router (config-line) password cisco (19)Router (config-line) exit (20)Router (config) line vty 0 4 (21)Router (config-line) login (22)Router (config-line) password cisco (23)Router (config-line) exit (24)Routerping 192.168.4.2Type escape sequence to abort.Sending 5, 100-byte ICMP Ethos to 192.168.4.2, timeout is 2 seconds:!!!!!Success rate is 100 percent (5/5) , round-trip min/avg/max = 24/25/28 msRoutertraceroute 192.168.4.2Type escape sequence to abort.Tracing the route to 192.168.4.21 192.168.2.2 16 msec 16 msecRoutertelnet 192.168.4.2Trying 192.168.4.2 ... OpenUser Access VerificationPassword:Router ＞Routerdebug ip rip (41)RIP protocol debugging is onRouter请解释第(8)、(12)、(41)行的意义及(17)～(20)与(21)～(24)行的作用。

3.Which command will delete the current rescue configuration?()A. user@router# system delete configuration rescueB. user@router> request system configuration rescue deleteC. user@router# delete rescue configurationD. user@router> file delete rescue-configuration

4.如果要对RIP进行调试排错,应该使用哪一个命令?()A.Router（config-router）#debug ip ripB.Router#show ip rip eventC.Router（config-router）#show ip interfaceD.Router#debug ip rip

更多“Which RIP configuration command allows the ERX Edge Router to send Unicast updates to configured neighbors?() ”相关问题

  • 第1题：

    ThenetworksetupforthistroubleticketisshowninFigure3.

    TroubleTicketStatement

    DSW1andR4cannotpingR2’sloopbackorR2’ss0/0/0/0.12IPv6address.InitialtroubleshootingshowsandR2isnotanOSPFv3neighboronR3.

    ConfigurationonR2

    ipv6unicast-routing!

    ipv6routerospf6

    router-id2.2.2.2!

    interfaces0/0/0/0.23

    ipv6address2026：：1：1/122

    ConfigurationR3

    ipv6unicast-routing!

    ipv6routerospf6

    router-id3.3.3.3!

    interfaces0/0/0/0.23

    ipv6address2026：：1：2/122

    ipv6ospf6area0

    Figure3

    OnWhichdeviceisthefaultconditionlocated?（）


    参考答案：C

  • 第2题：

    ThefollowingcommandisissuedonaCiscoRouter:Router(configuration)loggingconsolewarningsWhichalertswillbeseenontheconsole?()

    A.Warningsonly

    B.debugging，informational，notifications，warnings

    C.warnings，errors，critical，alerts，emergencies

    D.notifications，warnings，errors

    E.warnings，errors，critical，alerts


    参考答案：C

  • 第3题：

    如果要对 RIP进行调试排错，应该使用哪一个命令（） 。

    A．Router#debug ip rip

    B．Router(config)#debug ip rip

    C．Router#show router rip event

    D．Router(config)#show ip interface


    B

  • 第4题：

    What is the most likely reason for the dispartly between the actual network numbers at the branches and the routes in the routing table on Gateway－Router?()

    A. Branch-Router2 is configured to send both RIPv1 and RIPv2 updates.

    B. Gateway-Router is configured to only receive RIPv2 updates.

    C. Gateway-router is configured to receive only RIPv1 updates.

    D. Branch-Router1 is configured to only send RIPv1 updates


    参考答案：D

  • 第5题：

    What is themostlikelyreasonforthedispartlybetweentheactualnetworknumbersatthebranchesandtheroutesintheroutingtableonGateway－Router?()

    A.Branch-Router2isconfiguredtosendbothRIPv1andRIPv2updates.

    B.Gateway-RouterisconfiguredtoonlyreceiveRIPv2updates.

    C.Gateway-routerisconfiguredtoreceiveonlyRIPv1updates.

    D.Branch-Router1isconfiguredtoonlysendRIPv1updates.


    参考答案：D

  • 第6题：

    如果要对 RIP进行调试排错，应该使用哪一个命令（）。

    A．Router(config)#debug ip rip

    B．Router#show router rip event

    C．Router(config)#show ip interface

    D．Router#debug ip rip


    B

相关内容