If the bandwidth of an OSPF interface is configured with the "bandwidth 64"command, what would be the calculated cost of the link?()A. 1B. 64C. 1562D. 64000E. 1500

题目
If the bandwidth of an OSPF interface is configured with the "bandwidth 64"command, what would be the calculated cost of the link?()

A. 1

B. 64

C. 1562

D. 64000

E. 1500

相似考题

1.Which configuration command sets the MPLS interface bandwidth to 15 Mbps?()A. set bandwidth 15B. mpls bandwidth 15C. set bandwidth 15000D. mpls bandwidth 15000

2.When configuring OSPF on the ERX, what is the default auto－cost reference－bandwidth value?()A.AB.BC.CD.D

3.Refer to the exhibit. What must be done on router RTA to ensure that EIGRP works effectively in a Frame Relay multipoint environment?()A. Issue the command bandwidth 224 on the physical interface.B. Issue the command bandwidth 56 on the physical interface.C. Issue the command bandwidth 224 on each subinterface.D. Issue the command bandwidth 56 on each subinterface.

4.In JUNOS software, what is the default interface metric for IS－IS?()A.1B.10C.100D.10^8/link bandwidth

更多“If the bandwidth of an OSPF interface is configured with the "bandwidth 64"command, what would be the calculated cost of the link?() ”相关问题

  • 第1题：

    What is the default metric used on IS －IS routers for each interface?()

    A. The cost is set to 10 for all interfaces.

    B. The cost is set to 10 for LAN interfaces and 20 for WAN interfaces.

    C. The cost is based on the speed of the interface.

    D. The cost is based o n a composite of bandwidth and delay of the interface.


    参考答案：A

  • 第2题：

    If the bandwidth of an OSPF interface is 64, what would be the calculated cost of the link?()

    A. 1

    B. 10

    C. 1562

    D. 64000

    E. 128000

    F. None of the above


    参考答案：C

  • 第3题：

    If the bandwidth of an OSPF interface is 64, what would be the calculated cost of the link?（）

    • A、1
    • B、10
    • C、1562
    • D、64000
    • E、128000
    • F、None of the above

    正确答案:C

  • 第4题：

    What is  the default metric used on IS -IS routers for each interface?（）

    • A、The cost is set to 10 for all interfaces.
    • B、The cost is set to 10 for LAN interfaces and 20 for WAN interfaces.
    • C、The cost is based on the speed of the interface.
    • D、The cost is based o n a composite of bandwidth and delay of the interface.

    正确答案:A

  • 第5题：

    Which parameter or parameters are used to calculate OSPF cost in cisco routers？（）

    • A、Bandwidth，Delay，and MTUB
    • B、andwidth
    • C、Bandwidth and MTU
    • D、Bandwidth，MTU，Reliability，Delay，and Load

    正确答案:B

  • 第6题：

    This question is about the formation of OSPF adjacency. An OSPF adjacency will not form correctly across a point-to-point link in the same area. Which would most likely cause this problem？（）

    • A、Each interface has a different OSPF cost.
    • B、Each interface is configured with secondary addresses as well as primary addresses.
    • C、Each interface has a different MTU size.
    • D、Each interface is configured with theip unnumbered loopback 0 command.

    正确答案:C

  • 第7题：

    What is the command to configure RSVP to reserve up to one-tenth of a Gigabit link，but only allow eachindividual flow to use 1 MB/s？（）

    • A、ip rsvp bandwidth 100000 1000
    • B、ip rsvp bandwidth 100000 1
    • C、ip rsvp bandwidth 10 1
    • D、ip rsvp bandwidth 1000000 1000

    正确答案:A

  • 第8题：

    When configuring OSPF on the ERX， what is the default auto-cost reference-bandwidth value？（）

    • A、 1 Mbps
    • B、 10 Mbps
    • C、 100 Mbps
    • D、 1000 Mbps

    正确答案:C

  • 第9题：

    单选题
    If the bandwidth of an OSPF interface is configured with the "bandwidth 64"command, what would be the calculated cost of the link?（）
    A

    1

    B

    64

    C

    1562

    D

    64000

    E

    1500


    正确答案： E
    解析： 暂无解析

  • 第10题：

    多选题
    Which two commands would change the default OSPF metric calculation for interface ge-0/3/0 in JUNOS software？（）
    A

    set interfaces ge-0/3/0 unit 0 metric 10

    B

    set protocols ospf reference-bandwidth 10g

    C

    set interfaces ge-0/3/0 unit bandwidth 10g

    D

    set protocols ospf area 0 interface ge-0/3/0 metric 10

    E

    set protocols ospf area 0 interface ge-0/3/0 bandwidth 10g


    正确答案： A,D
    解析： 暂无解析

  • 第11题：

    多选题
    The following output was taken from Router R3. A scan of R3's configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（） R3#show ip ospf interface brief Interface PID Area IP Address/Mask Cost State Nbrs F/C Se0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1 Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1 Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1
    A

    An a uto - cost reference - bandwidth 1000 command in router ospf mode

    B

    An auto - cost reference - bandwidth 2000 command in router ospf mode

    C

    An ip ospf cost 1000 interface S0/0/0.1 command in router ospf mode

    D

    An auto - cost reference - bandwidth 64700 command i n router ospf mode


    正确答案： C,B
    解析： 暂无解析

  • 第12题：

    单选题
    What is  the default metric used on IS -IS routers for each interface?（）
    A

    The cost is set to 10 for all interfaces.

    B

    The cost is set to 10 for LAN interfaces and 20 for WAN interfaces.

    C

    The cost is based on the speed of the interface.

    D

    The cost is based o n a composite of bandwidth and delay of the interface.


    正确答案： D
    解析： 暂无解析

  • 第13题：

    An OSPF interface has been configured with the bandwidth 64 command. What will be the calculated OSPF cost of this link?()

    A.1

    B.10

    C.1562

    D.64000

    E.128000


    参考答案：C

  • 第14题：

    Which parameter or parameters are used to calculate OSPF cost in cisco routers?()

    A. Bandwidth,Delay,and MTU

    B. Bandwidth

    C. Bandwidth and MTU

    D. Bandwidth , MTU,Reliability,Delay,and Load


    参考答案：B

  • 第15题：

    The following output was taken from Router R3. A scan of R3's configuration shows that no bandwidth commands have been configured in this router. Which of the following answers lists configuration settings could be a part of a configuration tha t results in the following output?（） R3#show ip ospf interface brief Interface PID Area IP Address/Mask Cost State Nbrs F/C Se0/0/0.2 3 34 10.10.23.3/29 647 P2P 1/1 Se0/0/0.1 3 34 10.10.13.3/29 1000 P2P 1/1 Fa0/0 3 34 10.10.34.3/24 20 BDR 1/1

    • A、An a uto - cost reference - bandwidth 1000 command in router ospf mode
    • B、An auto - cost reference - bandwidth 2000 command in router ospf mode
    • C、An ip ospf cost 1000 interface S0/0/0.1 command in router ospf mode
    • D、An auto - cost reference - bandwidth 64700 command i n router ospf mode

    正确答案:A,B

  • 第16题：

    In JUNOS software, what is the default interface metric for IS-IS?（）

    • A、1
    • B、10
    • C、100
    • D、10^8/link bandwidth

    正确答案:B

  • 第17题：

    An OSPF interface has been configured with the bandwidth 64 command. What will be the calculated OSPF cost of this link?（）

    • A、1
    • B、10
    • C、1562
    • D、64000
    • E、128000

    正确答案:C

  • 第18题：

    What is the command to configure RSVP to reserve up to one-tenth of a Gigabit link， but only allow each individual flow to use 1 MB/s？（）

    • A、ip rsvp bandwidth 10000 1000
    • B、ip rsvp bandwidth 100000 1
    • C、ip rsvp bandwidth 10 1
    • D、ip rsvp bandwidth 1000000 1000

    正确答案:A

  • 第19题：

    what is mean of ospf auto-cost reference-bandwidth？


    正确答案:The OSPF metric is calculated as the ref-bw value divided by the bandwidth value.The default ref-bw is 10^8bps.Cisco provides the command auto-cost reference-bandwidth， which allows the default reference bandwidth to be changed.

  • 第20题：

    问答题
    what is mean of ospf auto-cost reference-bandwidth？

    正确答案： The OSPF metric is calculated as the ref-bw value divided by the bandwidth value.The default ref-bw is 10^8bps.Cisco provides the command auto-cost reference-bandwidth， which allows the default reference bandwidth to be changed.
    解析： 暂无解析

  • 第21题：

    单选题
    Which configuration command sets the MPLS interface bandwidth to 15 Mbps?（）
    A

    set bandwidth 15

    B

    mpls bandwidth 15

    C

    set bandwidth 15000

    D

    mpls bandwidth 15000


    正确答案： D
    解析： 暂无解析

  • 第22题：

    单选题
    If the bandwidth of an OSPF interface is 64, what would be the calculated cost of the link?（）
    A

    1

    B

    10

    C

    1562

    D

    64000

    E

    128000

    F

    None of the above


    正确答案： C
    解析： 暂无解析

  • 第23题：

    单选题
    In JUNOS software, what is the default interface metric for IS-IS?（）
    A

    1

    B

    10

    C

    100

    D

    10^8/link bandwidth


    正确答案： A
    解析： 暂无解析

相关内容