The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopba

题目

The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1

A. Automatic 6to4

B. Manually configured tunnel

C. ISATAP

D. GRE

相似考题

1.Given the following router output,which configuration file will the router use at its next reload?()A.configB.clientqos.cnfC.startup-configD.running-configuration

2.The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1A. Automatic 6to4B. Manually configured tunnelC. ISATAPD. GRE

3.Router R1 has been conf igured with an ipv6 route 2000::／64 S0／0／0 64 command.Which of the following does the 64 at the end of the command represent?()A. MetricB. Administrative distanceC. Timeout (seconds)D. Prefix lengthE. Interface ID

4.An engineer is reviewing another engineer‘s sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）A. tunnel sourceB. tunnel destinationC. tunnel modeD. All these commands are requireD

更多“The following configuration exists on a router on one end of an IPv6 tunnel. Although the ”相关问题

  • 第1题：

    A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of t he 100 branch routers. All routers use point - to - point subinterfaces and one subnet per PVC. Which of the following is true about OSPF in this design?（）

    • A、The central site router has 100 fully adjacent neighborships with the 100 branches
    • B、The central  site router has neighborships with all branch routers, but fully adjacent neighbors with only two branches
    • C、The central site router has a neighborship with the Frame Relay switcH
    • D、None of the other answers is correct

    正确答案:A

  • 第2题：

    When implementing OSPFv3, which statement describes the configuration of OSPF areas?（）

    • A、In interface configuration mode, the OSPFv3 area ID combination assigns interfaces to OSPFv3 areas.
    • B、In router configuration mode, the network wildcard area ID combination assigns networks to OSPFv3 areas.
    • C、In interface configuration mode, the IPv6 OSPF process area ID combination assigns interfaces to OSPFv3 areas.
    • D、In router configuration mode, the IPv6 OSPF interface area ID combination assigns interfaces to OSPFv3 areas.

    正确答案:C

  • 第3题：

    You are planning a new VLAN-based network solution.  What is one item you should consider when creating your implementation plan as it concerns VLANs？（）

    • A、generic router and switch configuration parameters
    • B、end-to-end test plan after all components have been installed and  configured
    • C、administrator assignments
    • D、rollback plan

    正确答案:D

  • 第4题：

    Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（） ipv6 router eigrp 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000::1/64 ipv6 eigrp 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 eigrp 1

    • A、EIGRP works on F0/0 and S0/0/0 without further configuration
    • B、EIGRP works with the addition of one command: a no shutdown command in EIGRP router configuration modE
    • C、EIGRP works with the addition of one command: an eigrp router - id command in EIGRP router configurat ion modE
    • D、EIGRP for IPv6 needs at least two more configuration commands before it works on R1

    正确答案:D

  • 第5题：

    The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（） interface loopback 1 ip address 192.168.1.1 255.255.255.255 interface tunnel 2 ipv6 address 2002:C0A8:10 1::1/64 tunnel source loopback 1

    • A、Automatic 6to4
    • B、Manually configured tunnel
    • C、ISATAP
    • D、GRE

    正确答案:A

  • 第6题：

    Given the following MPLS L2 configuration command: mpls-relay 10.1.1.1 4 Which two statements true? （）(Choose two.)

    • A、This command is applied to the core router facing interface.
    • B、This command is applied to the customer facing interface.
    • C、The 4 is locally significant and identifies the layer 2 circuit.
    • D、The 4 must match exactly on the peer router configuration on the remote end.

    正确答案:B,D

  • 第7题：

    单选题
    Given the following router output,which configuration file will the router use at its next reload?（）
    A

    config

    B

    clientqos.cnf

    C

    startup-config

    D

    running-configuration


    正确答案： D
    解析： 暂无解析

  • 第8题：

    单选题
    You are planning a new VLAN-based network solution.  What is one item you should consider when creating your implementation plan as it concerns VLANs？（）
    A

    generic router and switch configuration parameters

    B

    end-to-end test plan after all components have been installed and  configured

    C

    administrator assignments

    D

    rollback plan


    正确答案： A
    解析： 暂无解析

  • 第9题：

    多选题
    Given the following MPLS L2 configuration command: mpls-relay 10.1.1.1 4 Which two statements true? （）(Choose two.)
    A

    This command is applied to the core router facing interface.

    B

    This command is applied to the customer facing interface.

    C

    The 4 is locally significant and identifies the layer 2 circuit.

    D

    The 4 must match exactly on the peer router configuration on the remote end.


    正确答案： B,D
    解析： 暂无解析

  • 第10题：

    单选题
    Which of the following should an administrator do after running a command from the console onthe perimeter router?（）
    A

    Update the configuration logs

    B

    Update the network wiring schematics

    C

    Update the network configuration procedures

    D

    Compare the configuration with the baseline


    正确答案： D
    解析： 暂无解析

  • 第11题：

    单选题
    A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of the 100 branch routers. Which of the following could be true about the number of EIGRP neighbor ships?（）
    A

    A partial mesh totaling 100: one between the central - site router and each of the 100 branches.

    B

    A full mesh  -  (101 * 100) / 2 = 5050 - One neighborship between each pair of routers.

    C

    101 - One between each router (including the central site) a nd its nearby PE router.

    D

    None of the answers is correct.


    正确答案： B
    解析： 暂无解析

  • 第12题：

    单选题
    An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router. Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
    A

    tunnel source

    B

    tunnel destination

    C

    tunnel mode

    D

    All these commands are requireD


    正确答案： D
    解析： 暂无解析

  • 第13题：

    Exhibit: The following are true with one of the TestKing routers: 1) The IOS image in flash is missing 2) No Network connectivity is available. 3) The router fallback IOS image is corrupt. How will this Cisco 2600 series router respond if the conditions listed in the exhibit exist during the boot process?（）

    • A、The router will enter setup mode.
    • B、The router will enter ROM monitor mode.
    • C、The router will enter global configuration mode.
    • D、The boot will hang until an IOS is available.

    正确答案:B

  • 第14题：

    Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）

    • A、Metric
    • B、Administrative distance
    • C、Timeout (seconds)
    • D、Prefix length
    • E、Interface ID

    正确答案:B

  • 第15题：

    The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（） interface loopback 1 ip address 1.1.1.1 255.255.255.255 interface tunnel 2 ipv6 address 2000::1::/64 tunnel source loopback 1 tunnel destina tion 2.2.2.2 tunnel mode ipv6ip ipv6 eigrp 1

    • A、Automatic 6to4
    • B、Manually configured tunnel
    • C、ISATAP
    • D、GRE

    正确答案:B

  • 第16题：

    Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（） ipv6 unicast- routing interface f0/0 ipv6 rip one enable ipv6 address 2000::1/64 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 rip one enable

    • A、RIPng will be enabled on no interfaces.
    • B、RIPng will be enabled on one interface.
    • C、RIPng will  be enabled on two interfaces.
    • D、RIPng will advertise about prefixes connected to S0/0/0 and F0/0, but only send Updates on one interface.

    正确答案:B

  • 第17题：

    For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?（）

    • A、The router must have one routing protocol configured, but configuration for both routing protocols is not necessary
    • B、The router must hav e at least one working link connected to each routing domain
    • C、The redistribute command must be configured under EIGRP to send the routes to OSPF
    • D、The redistribute command should be configured under OSPF to take routes from EIGRP into OSPF

    正确答案:B,D

  • 第18题：

    单选题
    Exhibit: The following are true with one of the TestKing routers: 1) The IOS image in flash is missing 2) No Network connectivity is available. 3) The router fallback IOS image is corrupt. How will this Cisco 2600 series router respond if the conditions listed in the exhibit exist during the boot process?（）
    A

    The router will enter setup mode.

    B

    The router will enter ROM monitor mode.

    C

    The router will enter global configuration mode.

    D

    The boot will hang until an IOS is available.


    正确答案： B
    解析： 暂无解析

  • 第19题：

    单选题
    Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（） ipv6 router ospf 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000 ::1/64 ipv6 ospf 1 area 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 ospf 1 area 0
    A

    OSPF works on F0/0 and S0/0/0 without further configuration

    B

    OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modE

    C

    OSPF works with the addition of one command: an router - id command in OSPF router configuration modE

    D

    OSPFv3 needs at least two more configuration commands before it works on R1


    正确答案： C
    解析： 暂无解析

  • 第20题：

    多选题
    For a router to successfully redistribute routes between OSPF and EIGRP, which of the following are true?（）
    A

    The router must have one routing protocol configured, but configuration for both routing protocols is not necessary

    B

    The router must hav e at least one working link connected to each routing domain

    C

    The redistribute command must be configured under EIGRP to send the routes to OSPF

    D

    The redistribute command should be configured under OSPF to take routes from EIGRP into OSPF


    正确答案： D,A
    解析： 暂无解析

  • 第21题：

    单选题
    An administrator needs to update a router configuration for a router that does not support SSH.Which of the following can be used to securely update the router configuration?（）
    A

    FTP

    B

    SNMPv2

    C

    TFTP

    D

    KTTPS


    正确答案： D
    解析： 暂无解析

  • 第22题：

    单选题
    A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of t he 100 branch routers. All routers use point - to - point subinterfaces and one subnet per PVC. Which of the following is true about OSPF in this design?（）
    A

    The central site router has 100 fully adjacent neighborships with the 100 branches

    B

    The central  site router has neighborships with all branch routers, but fully adjacent neighbors with only two branches

    C

    The central site router has a neighborship with the Frame Relay switcH

    D

    None of the other answers is correct


    正确答案： A
    解析： 暂无解析

  • 第23题：

    单选题
    Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（） ipv6 unicast- routing interface f0/0 ipv6 rip one enable ipv6 address 2000::1/64 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 rip one enable
    A

    RIPng will be enabled on no interfaces.

    B

    RIPng will be enabled on one interface.

    C

    RIPng will  be enabled on two interfaces.

    D

    RIPng will advertise about prefixes connected to S0/0/0 and F0/0, but only send Updates on one interface.


    正确答案： B
    解析： 暂无解析

  • 第24题：

    单选题
    Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
    A

    Metric

    B

    Administrative distance

    C

    Timeout (seconds)

    D

    Prefix length

    E

    Interface ID


    正确答案： D
    解析： 暂无解析

相关内容