Refer to the exhibit. Router RT - 1 and router RT - 2 both advertise network 131.25.0.0/16 to routerRT - 3 via internal BGP. What is the reason that router RT - 3 chose router RT - 1 as its best path tonetwork 131.25.0.0/16.（）A. It has a better router IDB

Refer to the exhibit. EIGRP had converged in AS 1 when the link between router R1 and R2 went down. The console on router R2 generated the following messages:*Mar 20 12:12:06: %DUAL - 5NBRCHANG E: IP - EIGRP 1: Neighbor 10.1.4.3 (Serial0) is down: stuck in active*Mar 20 12:15:23: %DUAL -3- SIA: Route 10.1.1.0/24 stuck - in - active state in IP - EIGRP 1.Cleaning up The network administrator issued the show ip eigrp topology active command on R2 to check the status of the EIGRP network.Which statement best describes the reason for the error messages?（）

A. Incorrect bandwidth configuration on router R3 prevents R2 from establishing neighbor adjacency.

B. Incorrect bandwidth configuration on router R 5 prevents R2 from establishing neighbor adjacency.

C. Router R3 did not reply to the query about network 10.1.1.0/24 sent by router R2 .

D. Router R5 did not reply to the query about network 10.1.1.0/24 sent by router R2 .

Refer to the exhibit. Router B and router C are performing mutual redistribution between OSPF and EIGRP, and their default metrics are configured the same. Router D has equal cost paths to networks where both paths are not r eally equal cost. For example, network 172.16.54.0 shows equal cost through both router B and router C, though in reality the cost is greater using router C. Other routers, though not shown, are connected to the 172.16.54.0 and 172.16.55.0 networks, and the same issues exist to those routers and the networks connected to them. What can be done so that data will be routed along the most optimal path in the network? （）

A. Redistribute connected interfaces on router B and router C

B. Set the maximum nu mber of equal cost paths to1 in all routers

C. When redistributing EIGRP into OSPF, set the external metric type to type E1

D. Adjust the default metrics in router B and router C so that the values are different in each router

E. None of these solut ions will fix the problem. Migrate to a single dynamic routing protocol

Refer to the exhibits. Router B should advertise the network co nnected to the E0/0/0 interface to router A and block all other network advertisements. The IP routing table on router A indicates that it is not receiving this prefix from router B. What is the probable cause of the problem?（）

A. An access list on router B is causing the 192.168.3.16/28 network to be denied

B. An access list on router B is causing the 192.168.3.32/28 network to be denied

C. The distribute list on router B is referencing a numbered access list that does not exist on router B

D. The d istribute list on router B is referencing the wrong interface

Refer to the exhibit. A network administrator wants to reduce the number of OSPF routes advertised from Area 1 into Area 2. As the router configuration specialist, what two things would you do to accomplish this goal?（）

A. Enter the configuration on router B1.

B. Enter the configuration on router B4.

C. On the same router, enter the Summary - address 10.10.1.0 255.255.255.128 subcommand.

D. On the same router, enter the Area 1 range 10.10.1.0 255.255.255.128 subcommand.

E. On the same ro uter, enter the Area 2 range 10.10.1.0 255.255.255.128 subcommand.

A. the serial 1/1 address

B. the serial 2/0 address

C. a randomly generated internal address

D. the configured router - id address

Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）

A. both routers R1 and R2

B. router R1

C. router R2

D. none of the routers since they are not configured with static RP

A. In making its decision about the best path, RT - 1 gives precedence to the BGP MED values.

B. RT - 1 prefers internal BGP routes.

C. In making its decision about the best path, RT - 1 gives precedence to the origin code.

D. In makin g its decision about the best path, RT - 1 prefers the IGP metrics.

E. IP address 128.107.254.2 is lower than 128.107.255.2.

F. IP address 128.107.2.2 is lower than 128.107.255.2.

Refer to the exhibit. Router RTA is the hub router for routers RTB and RTC. The Frame Relay network is configured with EIGRP, and the entire network is in autonomous system 1. However,router RTB a nd RTC are not receiving each other‘s routes. What is the solution?（）

A.Check and change the access lists on router RTA

B.Configure the auto summary command under router eigrp 1 on router RTA

C.Configure subinterfaces on the spoke routers and assig n different IP address subnets for each subinterface

D.Issue the no ip split horizon command on router RTA

E.Issue the no ip split horizon eigrp 1 command on router RTA

F.Configure a distribute list on router RTA that allows it to advertise all r outes to the spoke routers

A.Router（config-router）#network154.2.1.0

B.outer（config-router）#network164.2.1.0

C.Router（config-router）#network-advertise154.2.1.0

D.Router（config-router）#network154.2.1.0mask255.255.255.0

E.Noneoftheotheralternativesapply

Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）

A. Add the area 1 stub command on routers R1.

B. Add the always keyword to the default - information originate configuration command on router R2.

C. Remov e the default information originate configuration command from router R2 and place it on router R1.

D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.

Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）

A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcast

B. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - point

C. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3

D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253

Refer to the exhibit. ROUTE Enterprises has many stub networks in their enterprise network, such as router B and its associated network. EIGRP is to be implemented on router A so that neither the prefix for the S/0/0/0 interface nor the prefixes from router B appear in the routing tables for the router in the enterprise network. Which action will accomplish this goal?（）

A. Declare router B a stub router using the eigrp stub command.

B. Use the passive - interface command for interface Serial0/0/0.

C. Use a mask with the network command to exclude interface Serial0/0/0.

D. Implement a distribute list to exclude the link prefix from the routi ng updates.

A. The router will prefer the next hop of 172.16.1.1 for packets destined for the 192.168.1.0 network.

B. The router will prefer the next hop of 172.26.1.1 for packets destined for the 192.168.1.0 network.

C. The router will adve rtise the 192.168.1.0 network only to 172.30.1.1.

D. The router will advertise the 192.168.1.0 network only to 172.26.1.1.

E. The router will prefer the next hop of 172.26.1.1 for packets except those destined for the 192.168.1.0 network.

A.The router is in area 49.0001.0002

B.The router acts as a Level 1 - 2 router

C.CLNS routing is enable d for the router

D.The router has a system ID of 0003.0004

E.The interfaces have a functional IS - IS configuration

F.The network service access point selector (NSEL) byte has a value of 0

A. Router R2 will be preferred because it has the higher neighbor IP address.

B. Router R2 will be preferr ed because its neighbor has a lower autonomous system number.

C. Router R1 will be preferred because it has a lower local preference.

D. Router R2 will be preferred because it has a higher local preference.

E. Router R1 will be preferred because its nei ghbor has the higher autonomous system number.

F. Router R1 will be preferred because it has the lower neighbor IP address.

A. Router R1 will deny the 172.16.1.0/26 route while permitting the 172.16.1.64/27 route to be advertised.

B. Router R1 will advertise both rou tes.

C. Router R1 should be reconfigured with an ACL instead of an ip prefix - list command.

D. Router R1 will deny the 172.16.1.0/27 route while permitting the 172.16.1.0/26 route to be advertised.

A. R4(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1

B. R4(config)# ip default - network 10.0.0.0

C. R4(config - router)# default -information originate

D. R4(conf ig)# ip route 10.0.0.0 255.0.0.0 10.1.1.1

A.The loopback addresses are on different subnets

B.The value of the dead timers on the router are different

C.Route summarization is enabled on both routers

D.The process indentifier on router A is different than the process identifier on router B