Which statement is true about the command ipv6 ospf 1 area 0?()A. It must be issued before the network command to enable the OSPF pr ocess for IPv6.B. It must be issued after the network command to enable the OSPF process for IPv6.C. It must be issued in

题目
Which statement is true about the command ipv6 ospf 1 area 0?()

A. It must be issued before the network command to enable the OSPF pr ocess for IPv6.

B. It must be issued after the network command to enable the OSPF process for IPv6.

C. It must be issued in router global configuration mode to enable the OSPF process for IPv6.

D. It must be issued in interface configuration mode to ena ble the OSPF process for IPv6.

相似考题

1.Which statement is true about the frequency of OSPF LSA transmissions?()A.AB.BC.CD.D

2.Routers R1 and R2, OSPF neighbors in area 0 over their Fa0/0 interfaces (respectively), currently both successfully use OSPF MD5 authentication. The OSPF configuration includes the area 0 authentication command under the router ospf 1 command.Which of the following commands must have been configur ed on R1‘s Fa0/0 interface?（）A. ip ospf authentication nullB. ip ospf authentication message - digestC. ip ospf authentication -key whatever- it - isD. ip ospf message - digest - key 1 md5 whatever - it - isE. ip ospf md5 1 key whatever - it - is

3.Refer to the exhibit. The partial configuration for an OSPF ASBR and an Area 0 ABR is shown. Assume the OSPF configurations throughout the network are operable. Which statement about these configurations is true? （）A. The ASBR route - maps are basically useless, because there are no deny prefix - lists.B. LSA Type 5s wil l not be received by the ABR from the ASBR.C. The OSPF backbone will not learn any RFC 1918 addresses.D. The matched prefix - list addresses will be given a metric of 255, which is essentially unreachable.

4.Which configuration command places interfaces whose IP addresses are between 192.168.0.0 and 192.168.255.255 into OSPF area 0?()A.AB.BC.CD.D

参考答案和解析
参考答案：D
更多“Which statement is true about the command ipv6 ospf 1 area 0?() ”相关问题

  • 第1题：

    Refer to the exhibit. What two statements are true?()

    A. This is the designated router (DR) on the FastEthernet 0/0 link.

    B. The output was generated by the show ip interface c ommand.

    C. The router was configured with the commands:r outer ospf 1 network 172.16.6.0 0.0.0.255 area 1

    D. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.

    E. Interface FastEthernet 0/0 was configured with the ipv6 o spf 1 area 1 command.

    F. OSPF version 2 has been enabled to support IPv6.


    参考答案：D, E

  • 第2题：

    Refer to the exhibit. OSPF has been configured on all routers in the network and Area 1 has been configured as a NSSA. Which statement is true about the NSSA Area 1?()

    A. Only redistributed RIP routes will appear in Area 1. They will be advertised via t ype 7 LSAs

    B. No redistributed routes can appear in Area 1, only summary routes

    C. Redistributed RIP and IGRP routes will appear in Area 1. They will be advertised via type 5 LSAs

    D. Only redistributed IGRP routes will appear in Area 1. They will be advertised via type 7 LSAs


    参考答案：D

  • 第3题：

    Which statement about OSPF ASBR summary LSA is true？（）

    • A、It is generated by an ASBR and indicates the reachability to an ABR located in another area.
    • B、It is generated by ABR and indicates the reachability to an ASBR located in another AS.
    • C、It is generated by ABR and indicates reachability to itself.
    • D、It is generated by ABR and indicates the reachability to an ASBR located in another area.
    • E、It is generated by ASBR and indicates the reachability to an ABR.

    正确答案:D

  • 第4题：

    Which command enables OSPF for IPv6?（）

    • A、router ospf ipv6 process - id
    • B、ipv6 ospf process - id
    • C、router ospf process - id
    • D、ipv6 router ospf process - id

    正确答案:D

  • 第5题：

    Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（） ipv6 router ospf 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000 ::1/64 ipv6 ospf 1 area 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 ospf 1 area 0

    • A、OSPF works on F0/0 and S0/0/0 without further configuration
    • B、OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modE
    • C、OSPF works with the addition of one command: an router - id command in OSPF router configuration modE
    • D、OSPFv3 needs at least two more configuration commands before it works on R1

    正确答案:C

  • 第6题：

    Which statement is true about the frequency of OSPF LSA transmissions？（）

    • A、 They are configured per OSPF area.
    • B、 They are configured per virtual router.
    • C、 They are configured per OSPF process.
    • D、 They are configured per OSPF interface.

    正确答案:D

  • 第7题：

    Which statement is true about the command ipv6 ospf 1 area 0?（）

    • A、It must be issued before the network command to enable the OSPF pr ocess for IPv6.
    • B、It must be issued after the network command to enable the OSPF process for IPv6.
    • C、It must be issued in router global configuration mode to enable the OSPF process for IPv6.
    • D、It must be issued in interface configuration mode to ena ble the OSPF process for IPv6.

    正确答案:D

  • 第8题：

    单选题
    Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（） ipv6 router ospf 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000 ::1/64 ipv6 ospf 1 area 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 ospf 1 area 0
    A

    OSPF works on F0/0 and S0/0/0 without further configuration

    B

    OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modE

    C

    OSPF works with the addition of one command: an router - id command in OSPF router configuration modE

    D

    OSPFv3 needs at least two more configuration commands before it works on R1


    正确答案： C
    解析： 暂无解析

  • 第9题：

    单选题
    Which of the following answers can be verified as true based on the following command output from Router R1?（） R1#show ip ospf virtual - links Virtual Link OSPF_VL0 to router 4.4.4.4 is up Run as demand circuit DoNotAge LSA alloweD. Transit area 1, via interface FastEthernet0/1, Cost of using 3
    A

    R1 is configured with  an area 0 virtual - link 4.4.4.4 cost 3 command.

    B

    The ping 4.4.4.4 command on R1 must currently be successful.

    C

    R1's Fa0/0 OSPF cost is 3.

    D

    4.4.4.4 is known to R1 based on a Type 1 LSA in area 1.


    正确答案： A
    解析： 暂无解析

  • 第10题：

    多选题
    Which two of these steps are minimum requirements to configure OSPFv3 under IPv6？（）
    A

    Configure a routing process using the command ipv6 router ospf [process-id].

    B

    Add the network statement for the interfaces on which OSPF will run.

    C

    Configure OSPF on the interface that it will run on.

    D

    Use the passive-interface command on the interfaces on which OSPF should not run.

    E

    Enable routing.


    正确答案： D,A
    解析： 暂无解析

  • 第11题：

    单选题
    Which statement about OSPF authentication is true？（）
    A

    To enable OSPF authentication in a network， OSPF area 0 authentications must be enabled first

    B

    The payload of OSPF version 3 packets contains no authentication information

    C

    OSPF version 3 supports Advanced Encryption Standard

    D

    OSPF version 3 uses router ID as a key to encrypt OSPF hello packets

    E

    OSPF MD5 authentication uses TCP， and Plan Test authentication uses UDP


    正确答案： A
    解析： 暂无解析

  • 第12题：

    多选题
    Routers R1 and R2, OSPF neighbors in area 0 over their Fa0/0 interfaces (respectively), currently both successfully use OSPF MD5 authentication. The OSPF configuration includes the area 0 authentication command under the router ospf 1 command. Which of the following commands must have been configur ed on R1's Fa0/0 interface?（）
    A

    ip ospf authentication null

    B

    ip ospf authentication message - digest

    C

    ip ospf authentication -key whatever- it - is

    D

    ip ospf message - digest - key 1 md5 whatever - it - is

    E

    ip ospf md5 1 key whatever - it - is


    正确答案： B,E
    解析： 暂无解析

  • 第13题：

    Which of the following is an OSPF configuration parameter that is used on an ABR, but not on an internal router?()

    A. A virtual link to area 0.

    B. OSPF summarization command.

    C. default - cost extension to the area command.

    D. no - summary extension to the area stub comm and.

    E. None of the other alternatives apply


    参考答案：D

  • 第14题：

    Refer to the exhibit. A network associate has configured OSPF with the command:City(config-router) network 192.168.12.64 0.0.0.63 area 0After completing the configuration, the associate discovers that not all the interfaces are participating in OSPF. Which three of the interfaces shown in the exhibit will participate in OSPF according to this configuration statement? （）

    A.FastEthernet0 /0

    B.FastEthernet0 /1

    C.Serial0/0

    D.Serial0/1.102

    E.Serial0/1.103

    F.Serial0/1.104


    参考答案：B, C, D

  • 第15题：

    Which of the following is an OSPF configuration parameter that is used on an ABR, but not on an internal router？（）

    • A、A virtual link to area 0.
    • B、OSPF summarization command.
    • C、default - cost extension to the area command.
    • D、no - summary extension to the area stub comm and.
    • E、None of the other alternatives apply

    正确答案:D

  • 第16题：

    Which of the following are true statements regarding the characteristics of OSPF areas? Select all that apply.（）

    • A、All OSPF networks require the use of multiple areas
    • B、Multiple OSPF areas must connect to area 0
    • C、Single area OSPF networks must be configured in area 1
    • D、Areas can be assigned any number from 0 to 63535
    • E、Area 0 is called the backbone area
    • F、Each OSPF area need to be configured with a loopback interface

    正确答案:B,E

  • 第17题：

    Which statement about OSPF authentication is true？（）

    • A、To enable OSPF authentication in a network， OSPF area 0 authentications must be enabled first
    • B、The payload of OSPF version 3 packets contains no authentication information
    • C、OSPF version 3 supports Advanced Encryption Standard
    • D、OSPF version 3 uses router ID as a key to encrypt OSPF hello packets
    • E、OSPF MD5 authentication uses TCP， and Plan Test authentication uses UDP

    正确答案:B

  • 第18题：

    Which statement about the ip classless router command is true?（）

    • A、The ip classless command is enabled by default in recent versions of IOS.
    • B、The ip classless command should only be enabled when static routing is being used instead of a routing protocol.
    • C、The ip classless command should be enabled by the network administrator whenever RIPv1 or IGRP is being used.
    • D、The ip classless command should be enabled by the network administrator whenever OSPF, RIPv2, or EIGRP is being used.

    正确答案:A

  • 第19题：

    Which statement about the WebView submit command is true?（）

    • A、The submit command exits the GUI.
    • B、The submit command reboots the WX device.
    • C、The submit command saves and writes the configuration to flash.
    • D、The submit command is the same as the commit CLI command.

    正确答案:D

  • 第20题：

    单选题
    In IPv6, the interfaces running OSPF can be configured with multiple ad dress prefixes. Which statement is true about the IPv6 addresses that can be included into the OSPF process?" （）
    A

    Specific addresses can be selected using a prefix list.

    B

    Specific addresses can be selected using a route map.

    C

    Specific addresses cann ot be selected for importation into the OSPF process.

    D

    Specific addresses can be selected using an ACL.


    正确答案： A
    解析： 暂无解析

  • 第21题：

    多选题
    Which of the following are true statements regarding the characteristics of OSPF areas? Select all that apply.（）
    A

    All OSPF networks require the use of multiple areas

    B

    Multiple OSPF areas must connect to area 0

    C

    Single area OSPF networks must be configured in area 1

    D

    Areas can be assigned any number from 0 to 63535

    E

    Area 0 is called the backbone area

    F

    Each OSPF area need to be configured with a loopback interface


    正确答案： D,B
    解析： 暂无解析

  • 第22题：

    单选题
    Which statement is true about the command ipv6 ospf 1 area 0?（）
    A

    It must be issued before the network command to enable the OSPF pr ocess for IPv6.

    B

    It must be issued after the network command to enable the OSPF process for IPv6.

    C

    It must be issued in router global configuration mode to enable the OSPF process for IPv6.

    D

    It must be issued in interface configuration mode to ena ble the OSPF process for IPv6.


    正确答案： B
    解析： 暂无解析

  • 第23题：

    单选题
    In JUNOS software, which statement is true regarding the OSPF advertisement of the loopback IP address on the ABR?（）
    A

    When Area 0 is active, the loopback interface must be configured in OSPF for it to be advertised.

    B

    When Area 0 is active, the loopback address is automatically advertised into other areas.

    C

    When Area 0 is active, the OSPF router-id must match the loopback address for the loopback address to be advertised.

    D

    When Area 0 is active, the router-id must be configured for the loopback address to be advertised.


    正确答案： C
    解析： 暂无解析

  • 第24题：

    单选题
    Which statement is true about the frequency of OSPF LSA transmissions？（）
    A

     They are configured per OSPF area.

    B

     They are configured per virtual router.

    C

     They are configured per OSPF process.

    D

     They are configured per OSPF interface.


    正确答案： D
    解析： 暂无解析

相关内容