A.By adding all subnets listed by the show ip route connected command
B.By adding the subnets of working interfaces over which static neighbors have been defined
C.By adding subnets redistributed on the local router from another routing source
D.By adding all subnets listed by the show ip route static command
第1题:
Which type of EIGRP route entry describes a feasible successor?()
第2题:
Why does RouterA show multiple unequal cost paths to network 192.168.81.0/24()。
第3题:
Which two statements about the EIGRP DUAL process are correct?()
第4题:
In what location are EIGRP successor routes stored?()
第5题:
Which of the following are correct statements?()
第6题:
Which statements are true about EIGRP successor routes (Choose two.)()。
第7题:
Which of the following are methods EIGRP uses to initially populate (seed) its EIGRP topology table, before learning topology data from neighbors?()
第8题:
A network design shows that R1 has four different possible paths from itself to the Data Center subnets. Which one of the following commands is most likely to show you all the possible next - hop IP addresses for these four possible routes?()
第9题:
An EIGRP route will go active if there are no successors or feasible successors in the EIGRP topology table.
An EIGRP route will go passive if there are no successors in the EIGRP topology table.
DUAL will trigger an EIGRP query process while placing the flapping routes in the holddown state.
A feasible successor in the EIGRP topology table can become the successor only after all the query requests have been replied to.
The stuck in active state is caused when the wait for the query replies have timed out.
EIGRP queries are sent during the loading state in the EIGRP neighbor establishment process.
第10题:
A successor route is used by EIGRP to forward traffic to a destination.
Successor routes are saved in the topology table to be used if the primary route fails.
Successor routes are flagged as active in the routing table.
A successor route may be backed up by a feasible successor route.
Successor routes are stored in the neighbor table following the discovery process.
Successors are not used in EIGRP.
第11题:
EIGRP will not be accepted when configured on the actual RIPv2 routers.
OSPF will no longer be used in the routing table, because you only have EIGRP internal routes running.
OSPF will no longer be used in the routing table, because you only have EIGRP external routes running.
RIPv2 will populate its RIP database but not its routing table, because you only have EIGRP external routes running.
RIPv2 will populate its RIP database but not its routing table, because you only have EIGRP internal routes running.
OSPF database will have RIPv2 routes.
第12题:
a primary route,stored in the routing table
a backup route,stored in the routingt able
a backup route,stored in the topology table
A primary route,stored in the topology table
第13题:
Which table of EIGRP route information are held in RAM and maintained through the use of hello and update packets?()
第14题:
Which of the following statements regarding EIGRP successor routes is valid?()
第15题:
Half of your network uses RIPv2 and the other half runs OSPF. The networks do not communicate with each other. Which two of these factors describe the impact of activating EIGRP over each separate part? ()
第16题:
Which statements are true about EIGRP successor routes? ()
第17题:
Which of these statements is true of routing protocols in a hub-and-spoke IPsec VPN topology?()
第18题:
Which of the following are not BGRP data structures? (Choose all that apply.)()
第19题:
Which three statements about EIGRP are true?()
第20题:
In the routing table only.
In the neighbor table only.
In the topology table only.
In the routing table and neighbor table.
In the routing table and topology table.
In the topology table and neighbor table.
第21题:
A variance was configured for EIGRP autonomous system 109.
The EIGRP topology table displays all routes to a destination.
The EIGRP topology table shows only backup routes to a destination.
Multiple floating static routes were configured to network 192.168.81.0 via interface Serial0.
第22题:
A successor route is used by EIGRP to forward traffic to destination.
Successor routes are saved in the topology table to be used if the primary route fails.
Successor routes are flagged as active in the routing table.
A successor route may be backed up by a feasible successor route.
Successor routes are stored in the neighbor table following the discovery process.
第23题:
By adding all subnets listed by the show ip route connected command
By adding the subnets of working interfaces over which static neighbors have been defined
By adding subnets redistributed on the local router from another routing source
By adding all subnets listed by the show ip route static command
第24题:
show ip eigrp topology
show ip eigrp topology all - links
show ip route eigrp
show ip route eigrp all - links
show ip eigrp topology all - learned