A router has been configured with the commands router os pf 9, network 172.16.1.0 0.0.0.255 area 8, and network 172.16.0.0 0.0.255.255 area 9, in that order. No other OSPF -related commands have been configured. The answers list the IP addresses that coul

题目

A router has been configured with the commands router os pf 9, network 172.16.1.0 0.0.0.255 area 8, and network 172.16.0.0 0.0.255.255 area 9, in that order. No other OSPF -related commands have been configured. The answers list the IP addresses that could be assigned to this router‘s Fa0/0 interface.Which an swers list an IP address/prefix length that would cause the router to put Fa0/0 into area 9?（）

A. 172.16.0.1/23

B. 172.16.1.1/26

C. 172.16.1.1/24

D. 172.16.0.255/23

E. None of the other answers is correct.

相似考题

1.How can a Ezonexam administrator determine if a router has been configured when it is first powered up?A．A configured router prompts for a passwordB．A configured router goes to the privileged mode promptC．An un configured router goes into the setup dialogD．An un configured router goes to the enable mode prompt

2.Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcastB. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - pointC. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253

3.Refer to the exhibit. What two statements are true?()A. This is the designated router (DR) on the FastEthernet 0/0 link.B. The output was generated by the show ip interface c ommand.C. The router was configured with the commands:r outer ospf 1 network 172.16.6.0 0.0.0.255 area 1D. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.E. Interface FastEthernet 0/0 was configured with the ipv6 o spf 1 area 1 command.F. OSPF version 2 has been enabled to support IPv6.

4.Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP.Which one of the following is true?（）A. R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.B. For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.C. For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.D. No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.

参考答案和解析
参考答案：A, D
更多“A router has been configured with the commands router os pf 9, network 172.16.1.0 0.0.0.25 ”相关问题

  • 第1题：

    Refer to the exhibit The neighbor 10.1.1.1 weight 200 BGP configuration command has been configured on router A. What will be the result of this configuration? ()

    A. Router A will prefer the path through router B for network 172.20.0.0

    B. Router A will prefer the path through router C for network 172.20.0.0

    C. Packets from router D will prefer the path through router B for networks advertised by router A

    D. Packets from r outer D will prefer the path through router C for networks advertised by router A


    参考答案：A

  • 第2题：

    The OSPF process has been started and the networks have been configured for Area 0 as shown in the diagram. The network administrator has several options for configuring RouterB to ensure that it will be preferred as the designated router (DR) for the 172.16.1.0 /24 LAN segment. What configuration tasks could be used to establish this preference (Choose three.)（）。

    A.Configure the priority value of the Fa0/0 interface of RouterB to a higher value than any other interface on the Ethernet network.

    B.Change the router id of Router B by assigning the IP address 172.16.1.130/24 to the Fa0/0 interface of RouterB.

    C.Configure a loopback interface on RouterB with an IP address higher than any IP address on the other routers.

    D.Change the priority value of the Fa0/0 interface of RouterB to zero.

    E.Change the priority values of the Fa0/0 interfaces of RouterA and RouterC to zero.

    F.No further configuration is necessary.


    参考答案：A, C, E

  • 第3题：

    A router has been configured with the commands router os pf 9, network 172.16.1.0 0.0.0.255 area 8, and network 172.16.0.0 0.0.255.255 area 9, in that order. No other OSPF -related commands have been configured. The answers list the IP addresses that could be assigned to this router's Fa0/0 interface. Which an swers list an IP address/prefix length that would cause the router to put Fa0/0 into area 9?（）

    • A、172.16.0.1/23
    • B、172.16.1.1/26
    • C、172.16.1.1/24
    • D、172.16.0.255/23
    • E、None of the other answers is correct.

    正确答案:A,D

  • 第4题：

    The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）

    • A、The Gallant router has the wrong LMI type configured
    • B、Inverse ARP is providing the wrong PVC information to the Gallant router
    • C、The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command
    • D、The frame-relay map statement in the Attalla router for the PVC to Steele is not correct
    • E、The IP address on the serial interface of the Attalla router is configured incorrectly

    正确答案:D

  • 第5题：

    A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG. For which of the following cases would you expect a router to create and flood a Type 2 LSA?（）

    • A、When OSPF is enabled on a LAN interface, and the router is the only router connected to the subnet.
    • B、  When OSPF is enabled on a point - to -point serial link, and that router has both the higher router ID and higher interface IP address on the link.
    • C、When OSPF is enabled on a Frame Relay point - to - point subinterface, has the lower RID and lower subinterfa ce IP address, and otherwise uses default OSPF configuration on the interface.
    • D、When OSPF is enabled on a working LAN interface on a router, and the router has been elected BDR.
    • E、None of the other answers is correct.

    正确答案:E

  • 第6题：

    A router has been configured with the commands router eigrp 9 and network 72.16.1.0 0.0.0.255. No other EIGRP - related commands have been configured. The nswers list the IP addresses that could be assigned to this router's Fa0/0 interface. Which answers list an IP address/prefix length that would cause the router to enable IGRP on Fa0/0?（）

    • A、172.16.0.1/23
    • B、172.16.1.1/26
    • C、172.16.1.1/24
    • D、172 .16.0.255/23
    • E、None of the other answers is correct.

    正确答案:B,C

  • 第7题：

    A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem? （）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0

    • A、The process id is configured improperly
    • B、The OSPF area is configured improperly
    • C、The network wildcard mask is configured improperly
    • D、The network number is configured improperly
    • E、The AS is configured improperly
    • F、The network subnet mask is configuerd improperly

    正确答案:C

  • 第8题：

    A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）

    • A、one
    • B、three
    • C、two
    • D、zero

    正确答案:C

  • 第9题：

    多选题
    HSRP has been configured between two Company devices.  Which of the following describe  reasons for deploying HSRP？ （）
    A

    HSRP provides redundancy and fault tolerance

    B

    HSRP allows one router to automatically assume the function of the second router if the second  router fails

    C

    HSRP allows one router to automatically assume the function of the second router if the second  router starts

    D

    HSRP provides redundancy and load balancing


    正确答案： C,B
    解析： 暂无解析

  • 第10题：

    单选题
    A Cisco router has been configured, and the copy running-config startup-config command has been issued. When the router is power cycled, the router prompts with: "Would you like to enter the initial configuration dialog? [yes/no]" Why has this occurred?（）
    A

    There is an error in the router DRAM.

    B

    Te IOS image is corrupt.

    C

    The configuration register is set to 0x2142.

    D

    The TFTP server that contains the router configuration file is unreachable.

    E

    A boot system configuration command has placed the router into setup mode.


    正确答案： E
    解析： 暂无解析

  • 第11题：

    单选题
    A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（） Router(config)#router ospf 1 Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
    A

    The process id is configured improperly

    B

    The OSPF area is configured improperly

    C

    The network wildcard mask is configured improperly

    D

    The network number is configured improperly

    E

    The AS is configured improperly

    F

    The network subnet mask is configuerd improperly


    正确答案： F
    解析： 暂无解析

  • 第12题：

    多选题
    A router has been configured with the commands router os pf 9, network 172.16.1.0 0.0.0.255 area 8, and network 172.16.0.0 0.0.255.255 area 9, in that order. No other OSPF -related commands have been configured. The answers list the IP addresses that could be assigned to this router's Fa0/0 interface. Which an swers list an IP address/prefix length that would cause the router to put Fa0/0 into area 9?（）
    A

    172.16.0.1/23

    B

    172.16.1.1/26

    C

    172.16.1.1/24

    D

    172.16.0.255/23

    E

    None of the other answers is correct.


    正确答案： C,B
    解析： 暂无解析

  • 第13题：

    A company has a small network,consisting of a single switch and a single router.The switch has been configured with two vlans,and route-on-a-stick is being configured on the router for inter-vlan routing.A trunk is configured to connect the switch to the router.What is the minimum number of router subinterfaces that are required for all the vlans to communicate?（）

    A. one

    B. three

    C. two

    D. zero


    参考答案：C

  • 第14题：

    Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP. Which one of the following is true?（）

    • A、R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.
    • B、For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.
    • C、For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.
    • D、No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.

    正确答案:B

  • 第15题：

    A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）

    • A、For the two vlans to communicate，a network statement for the trunk interface needs to be added to the  OSPF configuration.
    • B、For the two vlans to communicate， a network statement for each subinterface needs to be  added  to the OSPF configuration.
    • C、Direct inter-vlan communication does not require OSPF
    • D、OSPF cannot be used if router-on-a-stick is configured on the router

    正确答案:C

  • 第16题：

    How can an administrator determine if a router has been configured when it is first powered up?（）

    • A、A configured router prompts for a password
    • B、A configured router goes to the privileged mode prompt
    • C、An un configured router goes into the setup dialog
    • D、An un configured router goes to the enable mode prompt

    正确答案:C

  • 第17题：

    Which of the following OSPF commands, when used together, will put the network 192.168.10.0/24 into OSPF area 0?（）

    • A、Router(config-router)# network 192.168.10.0 0.0.0.255 0
    • B、Router(config-router)# network 192.168.10.0 0.0.0.255 area 0
    • C、Router(config-router)# network 192.168.10.0 255.255.255.0 area 0
    • D、Router(config)# router ospf 0
    • E、Router(config)# router ospf 1

    正确答案:B,E

  • 第18题：

    Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）

    • A、Router(config)#router ospf 1
    • B、Router(config)#router ospf 0
    • C、Router(config)#router ospf area 0
    • D、Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
    • E、Router(config-router)#network 192.168.16.0 0.0.0.255 0
    • F、Router(config-router)#network 192.168.16.0 255.255.255.0 area 0

    正确答案:A,D

  • 第19题：

    Router R1 exists in an Enterprise that uses EIGRP as its routing protocol. The show ip route command output on router R1 lists the following phrase: "Gateway of last resort is 1.1.1.1 to network 2.0.0.0". Whic h of the following is most likely to have caused this output to occur on R1?（）

    • A、R1 has been configured with an ip default- network 2.0.0.0 command.
    • B、R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command.
    • C、R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
    • D、Another router has been configured with an ip default - network 2.0.0.0 command.
    • E、Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.

    正确答案:D

  • 第20题：

    单选题
    The Frame Relay network in the diagram is not functioning properly. What is the cause of the problem?（）
    A

    The Gallant router has the wrong LMI type configured

    B

    Inverse ARP is providing the wrong PVC information to the Gallant router

    C

    The S3 interface of the Steele router has been configured with the frame-relay encapsulation ietf command

    D

    The frame-relay map statement in the Attalla router for the PVC to Steele is not correct

    E

    The IP address on the serial interface of the Attalla router is configured incorrectly


    正确答案： C
    解析： 暂无解析

  • 第21题：

    单选题
    A company has a small network，consisting of a single switch and a single router.The switch has beenconfigured with two vlans，and route-on-a-stick is being configured on the router for inter-vlan routing.Atrunk is configured to connect the switch to the router.What is the minimum number of router subinterfacesthat are required for all the vlans to communicate？（）
    A

    one

    B

    three

    C

    two

    D

    zero


    正确答案： D
    解析： 暂无解析

  • 第22题：

    单选题
    How can an administrator determine if a router has been configured when it is first powered up?（）
    A

    A configured router prompts for a password

    B

    A configured router goes to the privileged mode prompt

    C

    An un configured router goes into the setup dialog

    D

    An un configured router goes to the enable mode prompt


    正确答案： C
    解析： 暂无解析

  • 第23题：

    单选题
    You try to add a new router into the established Testking OSPF network. The networks attached to the new router do not appear in the routing tables of the other OSPF routers.The new router was configured for OSPF in the following way: Router(config)# router ospf 99 Router(config-if)# network 10.0.0.0 255.0.0.0 area 0 Based on this information, what is the most likely problem?（）
    A

    The process id is configured improperly.

    B

    The OSPF area is configured improperly.

    C

    The network wildcard mask is configured improperly.

    D

    The network number is configured improperly.

    E

    The AS is configured improperly.

    F

    The network subnet mask is configured improperly.

    G

    All of the above are likely problems.


    正确答案： C
    解析： 暂无解析

  • 第24题：

    单选题
    A switch has been configured with two vlans and is connected to a router with a trunk for inter-vlan routing.OSPF has been configured on the router，as the routing protocol for the network.Which statement about thisnetwork is true？（）
    A

    For the two vlans to communicate，a network statement for the trunk interface needs to be added to the  OSPF configuration.

    B

    For the two vlans to communicate， a network statement for each subinterface needs to be  added  to the OSPF configuration.

    C

    Direct inter-vlan communication does not require OSPF

    D

    OSPF cannot be used if router-on-a-stick is configured on the router


    正确答案： B
    解析： 暂无解析

相关内容