How is a loopback cleared on interface ge－0／0／0?()A.Issue the operational command clear interfaces ge-0/0/0 loopback local.B.No command is necessary, the loopback times-out in 5 minutes.C.Issue the configuration command clear interfaces ge-0/0/0 loopback,

题目
How is a loopback cleared on interface ge－0／0／0?()

A.Issue the operational command clear interfaces ge-0/0/0 loopback local.

B.No command is necessary, the loopback times-out in 5 minutes.

C.Issue the configuration command clear interfaces ge-0/0/0 loopback, then commit.

D.Issue the configuration command delete interfaces ge-0/0/0 gigether-options loopback , then commit.

相似考题

1.In the exhibit, what does the (>) symbol indicate?()A. There is a software issue with ge-1/0/1.0 interface.B. There is a hardware issue with ge-1/0/1.0 interface.C. The next hop of 172.25.213.11 is selected.D. The next hop of 172.25.213.11 is not resolvable.

2.Asystemadministratorwouldliketoresetstatisticstoinitialvaluespriortocollectingdevicestatisticsonent0interface.Whichofthefollowingcommandsshouldberuntoaccomplishthis?()A.netstat-vent0B.chdev-lent0-areset=trueC.entstat-rent0D.Ethernetinterfacevaluescannotbereset

3.Refertotheexhibit.WhichthreestatementsdescribethestepsthatarerequiredtoconfigureanIPsecsite－to－siteVPNusingaGREtunnel?()A.Thecommandaccess-list110permitgremustbeconfiguredtospecifywhichtrafficwillbeencrypted.B.Thecommandaccess-list110permitipmustbeconfiguredtospecifywhichhostscanusethetunnel.C.Thetunneldestination172.17.63.18commandmustbeconfiguredontheTunnel0interface.D.ThetunnelmodegrecommandmustbeconfiguredontheTunnel0interface.E.ThetunnelsourceEthernet1commandmustbeconfiguredontheTunnel0interface.F.ThetunnelsourceTunnel0commandmustbeconfiguredontheTunnel0interface.

4.In which two ways can the router ID selection be controlled?()A. Manually assign rid.B. configure local-address.C. enable the fxp0 interface.D. Assign nonmartian address to lo0.

参考答案和解析
参考答案：D
更多“How is a loopback cleared on interface ge－0／0／0?() ”相关问题

  • 第1题：

    The Testking router is running RIP as the routing protocol, and the IP routing table is displayed below:Gateway of last resort is 10.1.2.2 to network 0.0.0.010.0.0.0/24 is subnetted, 2 subnetsR 10.1.3.0 [120/1] via 10.1.2.2, 00:00:00, Serial0/0C 10.1.2.0 is directly connected, Serial0/0C 10.1.5.0 is directly connected, Serial0/1C 10.1.6.0 is directly connected, FastEthernet0/0R* 0.0.0.0/0 [120/1] via 10.1.5.5, 00:00:00, Serial0/1Based on the output above, if an administrator pings host 10.1.8.5 from host10.1.6.100, how will the router TestkingA process the ICMP packets?（）

    A. The packets will be discarded.

    B. The packets will be routed out the S0/0 interface.

    C. The packets will be routed out the S0/1 interface.

    D. The packets will be routed out the Fa0/0 interface.

    E. The packets will be routed through the 10.1.2.2 gateway.


    参考答案：C

  • 第2题：

    BasedonthefollowingoutputinR1,whichstatementistrue?()

    A.Ifalabeledpacketarriveswiththetopmostlabelof17，itwillbereplacedwithlabel19andsentouton Ethernet0/0interface.

    B.Ifalabeledpacketarriveswiththetopmostlabelof19，itwillbereplacedwithlabel17andsentouton Ethernet0/0interface.

    C.Ifalabeledpacketarriveswiththetopmostlabelof17，allthelabelswillberemovedandaclearIP PacketissenttoNextHop192.168.0.14onEthernet0/0.

    D.Noneoftheabove.


    参考答案：B

  • 第3题：

    一台路由器上loopback0的IP地址为10.1.1.1／32,在serial0／0／1上配置借用loopback0的IP地址的命令是().

    A.[Quidway] ip addresss erial0/0/1 equal loopback0

    B.[Quidway-serial0/0/1] ip addresss erial0/0/1 equa lloopback0

    C.[Quidway] ip address unnumbered interfaceserial0/0/1 loopback0

    D.[Quidway-serial0/0/1] ip address unnumbered interface loopback0


    参考答案：D

  • 第4题：

    Asanetworkengineer,studytheexhibitcarefully.RouterNetisunabletoestablishanADSLconnectionwithitsprovider.Whichactionwouldcorrectthisproblem?()

    A.OntheDialer0interface，addthepppoeenablecommand

    B.OntheDialer0Interface，addtheipmtu1496command

    C.OntheATM0/0interface，addthedialerpool-member1command

    D.OntheATM0/0interface，addthedialerpool-member0command


    参考答案：C

  • 第5题：

    Usetheoutputfromtheroutershowninthegraphicabovetodeterminewhichofthefollowingarecorrect.()

    A.Router John uses alink-state routing protocol.

    B.Router John will receive routing updates on the Serial0/0 interface.

    C.Router John will receive routing updates on the Serial0/1 interface.

    D.Router John will send routing updates out the Serial0/0 interface.

    E.Router John will send routing updates out the FastEthernet0/0 interface.

    F.Router John will send routing updates out the Serial0/1 interface.


    参考答案：B, D

相关内容