Which command is used to load a configuration from a TFTP server and merge the configuration into RAM?()A. copy running-config: TFTP:B. copy TFTP: running-configC. copy TFTP: startup-configD. copy startup-config: TFTP:

题目
Which command is used to load a configuration from a TFTP server and merge the configuration into RAM?()

A. copy running-config: TFTP:

B. copy TFTP: running-config

C. copy TFTP: startup-config

D. copy startup-config: TFTP:

相似考题

1.What will a new Ezonexam router do during startup if a configuration file is not located in NVRAM?A．It will search for the configuration file in the locations specified by boot system commands.B．It will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.C．It will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.D．It will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.E．It will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.

2.Which three actions must you perform as part of the WXOS software upgrade process?()(Choose three.)A. Reboot the device.B. Reapply the license key.C. Save the current configuration.D. Load the image using FTP, TFTP, or from the local disk.E. Back up the configration using FTP, TFTP, or to the local disk

3.Which command is used to load the rescue configuration?()A. load override rescueB. rollback rescueC. load replace rescue-configurationD. rollback 49

4.During startup, router VE1 displays the following error message:boot: cannot open "flash:"What will VE1 do next?A. It will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.B. It will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.C. It will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.D. Because of damaged flash memory, the router will fail the POST.E. It will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.F. None of the above

更多“Which command is used to load a configuration from a TFTP server and merge the configuration into RAM?() ”相关问题

  • 第1题：

    The following configuration command was entered into a router:ip route 172.16.3.0 255.255.255.0 192.168.2.4 Which of the following statements are true regarding this configuration change?()

    A. The default administrative distance is used.

    B. The command is used to establish a static route.

    C. The command is used to configure the router interfaces.

    D. The command is used to establish a stub network.

    E. The subnet mask for the source address is 255.255.255.0


    参考答案：A, B

  • 第2题：

    使用MML命令"ZUSU:MCMU,0:R=WARM,C=DSK"重启备份MCMU, 此MCMU会（）

    • A、Load software and configuration file from Hard disk
    • B、Load software only, no configuration file loading
    • C、Load configuration file from working MCMU and load software from hard disk
    • D、Load configuration file only, no software loading

    正确答案:C

  • 第3题：

    During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next（）。

    • A、Because of damaged flash memory, the router will fail the POST.
    • B、It will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.
    • C、It will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.
    • D、It will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.
    • E、It will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.

    正确答案:C

  • 第4题：

    What will a router do during startup if a configuration file is not located in NVRAM?（）

    • A、it will search for the configuration file in the locations specified by boot system commands.
    • B、it will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.
    • C、it will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.
    • D、it will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.
    • E、it will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.

    正确答案:C

  • 第5题：

    Which command is used to load the rescue configuration?（）

    • A、load override rescue
    • B、rollback rescue
    • C、load replace rescue-configuration
    • D、rollback 49

    正确答案:B

  • 第6题：

    Which command is used to load a configuration from a TFTP server and merge the configuration into RAM？（）

    • A、copy running-config: TFTP:
    • B、copy TFTP: running-config
    • C、copy TFTP: startup-config
    • D、copy startup-config: TFTP:

    正确答案:B

  • 第7题：

    Which configuration command is used to make the ERX Edge Router an NTP server？（）

    • A、 set ntp-server
    • B、 set ntp server
    • C、 ntp-server enable
    • D、 ntp server enable

    正确答案:D

  • 第8题：

    单选题
    Which command is used to load the rescue configuration?（）
    A

    load override rescue

    B

    rollback rescue

    C

    load replace rescue-configuration

    D

    rollback 49


    正确答案： B
    解析： 暂无解析

  • 第9题：

    多选题
    Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? （）
    A

    Router1 has specific boot system command that instruct it to load IOS from TFTP server.

    B

    Router1 is acting as a TFTP server for other routers.

    C

    Router1 cannot locate a valid IOS image in flash memory.

    D

    Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.

    E

    Cisco routers will first attempt to load a image from TFTP for management purposes.


    正确答案： E,C
    解析： 暂无解析

  • 第10题：

    单选题
    Which of the following is an accurate description of the command copy startup-configftp：//kevin：cisco@192.168.1.74？（）
    A

    The configuration on the FTP server is copied to RAM

    B

    The command is not valid on a Cisco router

    C

    The configuration file in RAM is copied to an FTP server

    D

    The configuration file in NVRAM is copied to an FTP server

    E

    The configuration on the FTP server is copied to NVRAM

    F

    The configuration will be copied from NVRAM to an FTP server with a filename of Kevin


    正确答案： B
    解析： 暂无解析

  • 第11题：

    单选题
    Which of the following should an administrator do after running a command from the console onthe perimeter router?（）
    A

    Update the configuration logs

    B

    Update the network wiring schematics

    C

    Update the network configuration procedures

    D

    Compare the configuration with the baseline


    正确答案： D
    解析： 暂无解析

  • 第12题：

    单选题
    Which command is used to copy the configuration from RAM into NVRAM？（）
    A

    copy running-config startup-config

    B

    copy startup-config: running-config

    C

    copy running config startup config

    D

    copy startup config running config

    E

    write terminal


    正确答案： B
    解析： 暂无解析

  • 第13题：

    Which command is used to copy the configuration from RAM into NVRAM?()

    A. copy running-config startup-config

    B. copy startup-config: running-config

    C. copy running config startup config

    D. copy startup config running config

    E. write terminal


    参考答案：A

  • 第14题：

    During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next?（）

    • A、Because of damaged flash memory， the router will fail the POST
    • B、It will attempt to locate the IOS from a TFTP server. If this fails， it will initiate the setup dialog.
    • C、It will attempt to locate the IOS from a TFTP server. If this fails， it will load a limited IOS from ROM
    • D、It will attempt to locate the configuration file from a TFTP server. If this fails， it will initiate the setup dialog.
    • E、It will attempt to locate the configuration file from a TFTP server. If this fails， it will load a limited configuration from ROM

    正确答案:C

  • 第15题：

    A Cisco router is booting and has just completed the POST process. It is now ready to find and load an IOS  image. What function does the router perform next?（）

    • A、It checks the configuration register.
    • B、It attempts to boot from a TFTP server.
    • C、It loads the first image file in flash memory.
    • D、It inspects the configuration file in NVRAM for boot instructions.

    正确答案:A

  • 第16题：

    Which of the following is an accurate description of the command copy startup-configftp：//kevin：cisco@192.168.1.74？（）

    • A、The configuration on the FTP server is copied to RAM
    • B、The command is not valid on a Cisco router
    • C、The configuration file in RAM is copied to an FTP server
    • D、The configuration file in NVRAM is copied to an FTP server
    • E、The configuration on the FTP server is copied to NVRAM
    • F、The configuration will be copied from NVRAM to an FTP server with a filename of Kevin

    正确答案:D

  • 第17题：

    Which command is used to copy the configuration from RAM into NVRAM?（）

    • A、copy running-config startup-config
    • B、copy startup-config: running-config
    • C、copy running config startup config
    • D、copy startup config running config
    • E、write terminal

    正确答案:A

  • 第18题：

    The following configuration command was entered into a router:ip route 172.16.3.0 255.255.255.0 192.168.2.4 Which of the following statements are true regarding this configuration change?（）

    • A、The default administrative distance is used.
    • B、The command is used to establish a static route.
    • C、The command is used to configure the router interfaces.
    • D、The command is used to establish a stub network.
    • E、The subnet mask for the source address is 255.255.255.0

    正确答案:A,B

  • 第19题：

    单选题
    During startup, the router displays the following error message: boot: cannot open "flash:" What will the router do next（）。
    A

    Because of damaged flash memory, the router will fail the POST.

    B

    It will attempt to locate the IOS from a TFTP server. If this fails, it will initiate the setup dialog.

    C

    It will attempt to locate the IOS from a TFTP server. If this fails, it will load a limited IOS from ROM.

    D

    It will attempt to locate the configuration file from a TFTP server. If this fails, it will initiate the setup dialog.

    E

    It will attempt to locate the configuration file from a TFTP server. If this fails, it will load a limited configuration from ROM.


    正确答案： C
    解析： 暂无解析

  • 第20题：

    单选题
    Which configuration command is used to make the ERX Edge Router an NTP server？（）
    A

     set ntp-server

    B

     set ntp server

    C

     ntp-server enable

    D

     ntp server enable


    正确答案： D
    解析： 暂无解析

  • 第21题：

    单选题
    A Cisco router is booting and has just completed the POST process. It is now ready to find and load an IOS  image. What function does the router perform next?（）
    A

    It checks the configuration register.

    B

    It attempts to boot from a TFTP server.

    C

    It loads the first image file in flash memory.

    D

    It inspects the configuration file in NVRAM for boot instructions.


    正确答案： C
    解析： 暂无解析

  • 第22题：

    多选题
    The following configuration command was entered into a router:ip route 172.16.3.0 255.255.255.0 192.168.2.4 Which of the following statements are true regarding this configuration change?（）
    A

    The default administrative distance is used.

    B

    The command is used to establish a static route.

    C

    The command is used to configure the router interfaces.

    D

    The command is used to establish a stub network.

    E

    The subnet mask for the source address is 255.255.255.0


    正确答案： D,C
    解析： 暂无解析

  • 第23题：

    单选题
    Which command is used to load a configuration from a TFTP server and merge the configuration into RAM?（）
    A

    copy running-config: TFTP

    B

    copy TFTP: running-config

    C

    copy TFTP: startup-config

    D

    copy startup-config: TFTP


    正确答案： D
    解析： 暂无解析

相关内容