Refer to the exhibit.What is the reason that the interface status is “administratively down,line protocol down”?()A.There is a mismatch in encapsulation typesB.The wrong type of cable is connected to the interfaceC.The interface has been configured with t

题目
Refer to the exhibit.What is the reason that the interface status is “administratively down,line protocol down”?()

A.There is a mismatch in encapsulation types

B.The wrong type of cable is connected to the interface

C.The interface has been configured with the shutdown command

D.The interface is not receiving any keepalives

E.The interface needs to be configured as a DTE device

F.There is no encapsulation type configured

相似考题

1.如果链路的一端被管理DOWN,你将看到的另一端接口状态输出信息是()A.interface is down，line protocol is downB.interface is down，line protocol is upC.interface is up，line protocol is downD.interface is up，line protocol is up

2.After issuing the show interfaces terse command, you notice that the status of one interface is "up down". What does this indicate?"()A.Layer 1 on the interface is up but Layer 2 is down.B.Layer 2 on the interface is up but Layer 3 has not been configured.C.The interface is administratively up but the link status is down.D.The interface is up but has been administratively turned off.

3.Which line from the output of the show ip interface command indicates that there is a Layer 1 problem?A．Serial0/1 is up, line protocol is downB．Serial0/1 is down, line protocol is downC．Serial0/1 is up, line protocol is upD．Serial0/1 is administratively down, line protocol is downE．None of the above

4.Which three commands will cause a logical interface to go administratively down after being committed?()A. shutdownB. deactivateC. disableD. downE. delete

更多“Refer to the exhibit.What is the reason that the interface status is “administratively down,line protocol down”?() ”相关问题

  • 第1题：

    While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）

    A. Serial 0 is up, line protocol is up

    B. Serial 0 is up, line protocol is down

    C. Serial 0 is down, line protocol is down

    D. Serial 0 is down, line protocol is up

    E. Serial 0 is administratively down, line protocol is down

    F. Serial 0 is administratively down, line protocol is up


    参考答案：E

  • 第2题：

    当学生A用两台Star—R2624路由器在做路由器广域网口连通实验时误将本端口路由器V.35线缆的插头插倒了。结果发现PING直连的路由器不通,请问此时需要查看路由器的状态应该是()

    A.Serial 0 is up，line protocol is down

    B.Serial 0 is down，line protocol is down

    C.Serial 0 is down，line protocol is up

    D.Serial 0 is administratively down，line protocol is


    参考答案：A

  • 第3题：

    PPP链路的状态为serial number is administratively down,line protocol is down时，说明（）。  

    • A、物理链路有问题
    • B、接口被管理员shutdown了
    • C、参数配置不正确
    • D、没大问题，重启路由器就行了

    正确答案:B

  • 第4题：

    下列（）状态是不可能在路由器的串行端口状态见到的。

    • A、 Interface is up， line protocol is up
    • B、 Interface is down， line protocol is down
    • C、 Interface is down， line protocol is up
    • D、 Interface is up， line protocol is down

    正确答案:C

  • 第5题：

    当学生A用两台Star—R2624路由器在做路由器广域网口连通实验时误将本端口路由器V.35线缆的插头插倒了。结果发现PING直连的路由器不通，请问此时需要查看路由器的状态应该是（）

    • A、Serial 0 is up，line protocol is down
    • B、Serial 0 is down，line protocol is down
    • C、Serial 0 is down，line protocol is up
    • D、Serial 0 is administratively down，line protocol is

    正确答案:A

  • 第6题：

    Refer to the exhibit.What is the reason that the interface status is “administratively down,line protocol down”?（）

    • A、There is a mismatch in encapsulation types
    • B、The wrong type of cable is connected to the interface
    • C、The interface has been configured with the shutdown command
    • D、The interface is not receiving any keepalives
    • E、The interface needs to be configured as a DTE device
    • F、There is no encapsulation type configured

    正确答案:C

  • 第7题：

    如果链路的一端被管理DOWN，你将看到的另一端接口状态输出信息是（）

    • A、interface is down，line protocol is down
    • B、interface is down，line protocol is up
    • C、interface is up，line protocol is down
    • D、interface is up，line protocol is up

    正确答案:C

  • 第8题：

    单选题
    After issuing the show interfaces terse command, you notice that the status of one interface is "up down". What does this indicate?"（）
    A

    Layer 1 on the interface is up but Layer 2 is down.

    B

    Layer 2 on the interface is up but Layer 3 has not been configured.

    C

    The interface is administratively up but the link status is down.

    D

    The interface is up but has been administratively turned off.


    正确答案： C
    解析： 暂无解析

  • 第9题：

    单选题
    While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）
    A

    Serial 0 is up, line protocol is up

    B

    Serial 0 is up, line protocol is down

    C

    Serial 0 is down, line protocol is down

    D

    Serial 0 is down, line protocol is up

    E

    Serial 0 is administratively down, line protocol is down

    F

    Serial 0 is administratively down, line protocol is up


    正确答案： D
    解析： 暂无解析

  • 第10题：

    单选题
    如果链路的一端被管理DOWN，你将看到的另一端接口状态输出信息是（）
    A

    interface is down，line protocol is down

    B

    interface is down，line protocol is up

    C

    interface is up，line protocol is down

    D

    interface is up，line protocol is up


    正确答案： B
    解析： 暂无解析

  • 第11题：

    单选题
    A user has no network connectivity. A check of the associated port indicates that the interface is up，the line protocol is down. Which item would most likely cause this problem？（）
    A

    Speed mismatch

    B

    Incorrect encapsulation

    C

    MTU set too low

    D

    Duplex mismatch


    正确答案： A
    解析： 暂无解析

  • 第12题：

    多选题
    当用户端cisco路由器上用showinterface命令时line和lineprotocal可能出现的几种组合？（）。
    A

    line down；line protocol down

    B

    line down；line protocol

    C

    line up；line protocol down

    D

    line up；line protocol up


    正确答案： D,A
    解析： 暂无解析

  • 第13题：

    Which line from the output of the show ip interface command indicates a layer 1 problem?()

    A. Serial0/1 is up, line protocol is down

    B. Serial0/1 is down, line protocol is down

    C. Serial0/1 is up, line protocol is up

    D. Serial0/1 is administratively down, line protocol is down


    参考答案：B

  • 第14题：

    当用户端cisco路由器上用showinterface命令时line和lineprotocal可能出现的几种组合?()。

    A.line down；line protocol down

    B.line down；line protocol

    C.line up；line protocol down

    D.line up；line protocol up


    参考答案：A, C, D

  • 第15题：

    While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）

    • A、Serial 0 is up, line protocol is up
    • B、Serial 0 is up, line protocol is down
    • C、Serial 0 is down, line protocol is down
    • D、Serial 0 is down, line protocol is up
    • E、Serial 0 is administratively down, line protocol is down
    • F、Serial 0 is administratively down, line protocol is up

    正确答案:E

  • 第16题：

    TDCS中使用show interface命令查看路由器接口如显示line Protocol is down说明（）。

    • A、接口故障
    • B、接口正常
    • C、协议正常
    • D、协议故障

    正确答案:D

  • 第17题：

    当用户端cisco路由器上用showinterface命令时line和lineprotocal可能出现的几种组合？（）。

    • A、line down；line protocol down
    • B、line down；line protocol
    • C、line up；line protocol down
    • D、line up；line protocol up

    正确答案:A,C,D

  • 第18题：

    Which line from the output of the show ip interface command indicates a layer 1 problem?（）

    • A、Serial0/1 is up, line protocol is down
    • B、Serial0/1 is down, line protocol is down
    • C、Serial0/1 is up, line protocol is up
    • D、Serial0/1 is administratively down, line protocol is down

    正确答案:B

  • 第19题：

    Which three commands will cause a logical interface to go administratively down after being committed?（）

    • A、shutdown
    • B、deactivate
    • C、disable
    • D、down
    • E、delete

    正确答案:B,C,E

  • 第20题：

    单选题
    TDCS中使用show interface命令查看路由器接口如显示line Protocol is down说明（）。
    A

    接口故障

    B

    接口正常

    C

    协议正常

    D

    协议故障


    正确答案： D
    解析： 暂无解析

  • 第21题：

    多选题
    Which three commands will cause a logical interface to go administratively down after being committed?（）
    A

    shutdown

    B

    deactivate

    C

    disable

    D

    down

    E

    delete


    正确答案： E,D
    解析： 暂无解析

  • 第22题：

    单选题
    Refer to the exhibit.What is the reason that the interface status is “administratively down,line protocol down”?（）
    A

    There is a mismatch in encapsulation types

    B

    The wrong type of cable is connected to the interface

    C

    The interface has been configured with the shutdown command

    D

    The interface is not receiving any keepalives

    E

    The interface needs to be configured as a DTE device

    F

    There is no encapsulation type configured


    正确答案： C
    解析： 暂无解析

  • 第23题：

    单选题
    PPP链路的状态为serial number is administratively down，line protocol is down时，说明（）。
    A

    物理链路有问题

    B

    接口被管理员shutdown了

    C

    参数配置不正确

    D

    没大问题，重启路由器就行了


    正确答案： B
    解析： 暂无解析

相关内容