A network administrator creates a layer 3 EtherChannel, bundling four interfaces into channel group 1. On what interface is the IP address configured?()A.the port-channel 1 interfaceB.the highest number member interfaceC.all member interfacesD.the lowest

题目
A network administrator creates a layer 3 EtherChannel, bundling four interfaces into channel group 1. On what interface is the IP address configured?()

A.the port-channel 1 interface

B.the highest number member interface

C.all member interfaces

D.the lowest number member interface

相似考题

1.● TCP/IP communication protocol contains four layers. From bottom to top, the four layers are __(71)__.（71）A．network interface layer, internet layer, transport layer and application layerB．internet layer, network interface layer, transport layer and application layerC．network interface layer, transport layer, network interface layer and application layerD．application layer, transport layer, internet layer and network interface layer

2.TCP/IP communication protocol contains four layers． From bottom to top, the four layers are __（71）__．A.network interface layer, internet layer, transport layer and application layerB.internet layer, network interface layer, transport layer and application layerC.network interface layer, transport layer, network interface layer and application layerD.application layer, transport layer, internet layer and network interface layer

3.An administrator types in the command router ospf 1 and receives the er ror message: "OSPF process 1 cannot start." (Output is omitted.) What should be done to correctly set up OSPF?()A. Ensure that an interface has been configured with an IP addressB. Ensure that IP classless is enabledC. Ensure that the interfaces can ping their directly connected neighborsD. Ensure that an interface has been configured with an IP address and is up

4.After issuing the show interfaces terse command, you notice that the status of one interface is "up down". What does this indicate?"()A.Layer 1 on the interface is up but Layer 2 is down.B.Layer 2 on the interface is up but Layer 3 has not been configured.C.The interface is administratively up but the link status is down.D.The interface is up but has been administratively turned off.

更多“A network administrator creates a layer 3 EtherChannel, bundling four interfaces into channel group 1. On what interface is the IP address configured?() ”相关问题

  • 第1题：

    On the assumption that every OSPF router in a particular area is configured with there is no loopback interface set?()

    A. The IP address of the first Fast Ethernet interface.

    B. The IP address of the console management interface.

    C. The highest IP address among its active interfaces.

    D. The lowest IP address among its active interfaces.

    E. There will be no router ID until a loopback interface is configured.


    参考答案：C

  • 第2题：

    The OSPF process has been started and the networks have been configured for Area 0 as shown in the diagram. The network administrator has several options for configuring RouterB to ensure that it will be preferred as the designated router (DR) for the 172.16.1.0 /24 LAN segment. What configuration tasks could be used to establish this preference (Choose three.)（）。

    A.Configure the priority value of the Fa0/0 interface of RouterB to a higher value than any other interface on the Ethernet network.

    B.Change the router id of Router B by assigning the IP address 172.16.1.130/24 to the Fa0/0 interface of RouterB.

    C.Configure a loopback interface on RouterB with an IP address higher than any IP address on the other routers.

    D.Change the priority value of the Fa0/0 interface of RouterB to zero.

    E.Change the priority values of the Fa0/0 interfaces of RouterA and RouterC to zero.

    F.No further configuration is necessary.


    参考答案：A, C, E

  • 第3题：

    Which of these is true regarding the configuration and application of port access control lists？ （）

    • A、PACLs can be applied in the inbound or outbound direction of a Layer 2 physical interface. 
    • B、At Layer 2， a MAC address PACL will take precedence over any existing Layer 3 PACL.
    • C、When you apply a port ACL to a trunk port， the ACL filters traffic on all VLANs present on the trunk port.
    • D、PACLs are not supported on EtherChannel interfaces.

    正确答案:D

  • 第4题：

    A network administrator creates a layer 3 EtherChannel, bundling four interfaces into channel group 1. On what interface is the IP address configured?（）

    • A、the port-channel 1 interface
    • B、the highest number member interface
    • C、all member interfaces
    • D、the lowest number member interface

    正确答案:A

  • 第5题：

    Company.com with an EtherChannel implementation is considering an HACMP solution. What considerations must be addressed in planning this configuration？（）  

    • A、 Hardware address takeover must be configured.
    • B、 IPAT via IP aliasing is required for EtherChannel.
    • C、 EtherChannel must be defined as a separate network.
    • D、 HACMP does not support the fallover of EtherChannel.

    正确答案:D

  • 第6题：

    An AIX server has 2 network interfaces and the system administrator wants to enable the users on the locally configured network interface to be able to connect to systems configured on the global network interface.  How is it accomplished？（）

    • A、Enable routed on the server
    • B、Enable gated on the server
    • C、Enable ipforwarding on the server
    • D、Set network options back to default

    正确答案:C

  • 第7题：

    单选题
    If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?（）
    A

    the IP address of the first Fast Ethernet interface

    B

    the IP address of the console management interface

    C

    the highest IP address among its active interfaces

    D

    the lowest IP address among its active interfaces

    E

    the priority value until a loopback interface is configured


    正确答案： B
    解析： 暂无解析

  • 第8题：

    单选题
    An administrator types in the command router ospf 1 and receives the er ror message: "OSPF process 1 cannot start." (Output is omitted.) What should be done to correctly set up OSPF？（）
    A

    Ensure that an interface has been configured with an IP address

    B

    Ensure that IP classless is enabled

    C

    Ensure that the interfaces can ping their directly connected neighbors

    D

    Ensure that an interface has been configured with an IP address and is up


    正确答案： A
    解析： 暂无解析

  • 第9题：

    单选题
    Company.com with an EtherChannel implementation is considering an HACMP solution. What considerations must be addressed in planning this configuration？（）
    A

     Hardware address takeover must be configured.

    B

     IPAT via IP aliasing is required for EtherChannel.

    C

     EtherChannel must be defined as a separate network.

    D

     HACMP does not support the fallover of EtherChannel.


    正确答案： A
    解析： 暂无解析

  • 第10题：

    单选题
    Routers R1 and R2 are configured for HSRP as shown below：   Router R1：   interface ethernet 0   ip address 20.6.2.1 255.255.255.0   standby 35 ip 20.6.2.21   standby 35 priority 100   interface ethernet 1   ip address 20.6.1.1.2 255.255.255.0   standby 34 ip 20.6.1.21    Router R2：   interface ethernet 0   ip address 20.6.2.2 255.255.255.0   standby 35 ip 20.6.2.21   interface ethernet 1   ip address 20.6.1.1.1 255.255.255.0   standby 34 ip 20.6.1.21  standby 34 priority 100   You have configured the routers R1 & R2 with HSRP. While debugging router R2 you notice very   frequent HSRP group state transitions.  What is the most likely cause of this？ （）
    A

     physical layer issues

    B

     no spanning tree loops

    C

     use of non-default HSRP timers

    D

     failure to set the command standby 35 preempt


    正确答案： B
    解析： 暂无解析

  • 第11题：

    单选题
    Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 & R2 with HSRP. While debugging router R2 you notice veryfrequent HSRP group state transitions. What is the most likely cause of this？（）
    A

    physical layer issues

    B

    no spanning tree loops

    C

    use of non-default HSRP timers

    D

    failure to set the command standby 35 preempt


    正确答案： D
    解析： 暂无解析

  • 第12题：

    单选题
    On the assumption that every OSPF router in a particular area is configured with there is no loopback interface set?（）
    A

    The IP address of the first Fast Ethernet interface.

    B

    The IP address of the console management interface.

    C

    The highest IP address among its active interfaces.

    D

    The lowest IP address among its active interfaces.

    E

    There will be no router ID until a loopback interface is configured.


    正确答案： D
    解析： 暂无解析

  • 第13题：

    Refer to the exhibit. Which three statements correctly describe Network Device A?()

    A.With a network wide mask of 255.255.255.128, each interface does not require an IP address.

    B.With a network wide mask of 255.255.255.128, each interface does require an IP address on a unique IP subnet.

    C.With a network wide mask of 255.255.255.0, must be a Layer 2 device for the PCs to communicate with each other.

    D.With a network wide mask of 255.255.255.0, must be a Layer 3 device for the PCs to communicate with each other.

    E.With a network wide mask of 255.255.254.0, each interface does not require an IP address.


    参考答案：B, D

  • 第14题：

    If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?（）

    • A、the IP address of the first Fast Ethernet interface
    • B、the IP address of the console management interface
    • C、the highest IP address among its active interfaces
    • D、the lowest IP address among its active interfaces
    • E、the priority value until a loopback interface is configured

    正确答案:C

  • 第15题：

    Which command is used to enable EtherChannel hashing for Layer 3 IP and Layer 4 port-based CEF？（）

    • A、mpls ip cef
    • B、port-channel ip cef
    • C、mpls ip port-channel cef
    • D、port-channel load balance
    • E、mpls ip load-balance
    • F、ip cef EtherChannel channel-id XOR L4
    • G、ip cef connection exchange

    正确答案:D

  • 第16题：

    On corporate network, hosts on the same VLAN can communicate with each other, but they are unable to communicate with hosts on different VLANs. What is needed to allow communication between the VLANs?（）

    • A、a router with subinterfaces configured on the physical interface that is connected to the switch
    • B、a router with an IP address on the physical interface connected to the switch
    • C、a switch with an access link that is configured between the switches
    • D、a switch with a trunk link that is configured between the switches

    正确答案:A

  • 第17题：

    A two-node cluster is configured for mutual takeover with two service IP labels. The cluster is Being tested for fallover behavior. Both nodes in the cluster have two network interfaces （ent0’ and ’ent1’） configured with IPAT via IP Replacement. When the network cable is removed from the interface card with the service address （’ent0’）， the service address is moved to ’ent1’， and ’ent0’ is reconfigured on its boot address. When the network cable is replaced on ’ent0，the service address does not switch back to ’ent0’.  What statement most accurately describes this situation？（）   

    • A、 EtherChannel is needed to automatically switch the service IP address back to ’ent0’.
    • B、 This is the default behavior for a network interface failure with this configuration.
    • C、 Gratuitous ARP support needs to be enabled for the IP Network Interface Module in SMIT.
    • D、 The Inactive Network Takeover option should be set to "true" to forece the service address back to ’ent0’.

    正确答案:B

  • 第18题：

    Which two statements are true about the primary address on an interface?（）

    • A、It is the address used by default as the local address for broadcast and multicast packets sourced locally and sent out of the interface.
    • B、You use the primary address when you have multiple IP addresses belonging to the same subnet on the same interface.
    • C、It can be useful for selecting the local address used for packets sent out of unnumbered interfaces when multiple non-127 addresses are configured on the loopback interface.
    • D、By default, the primary address on an interface is selected as the numerically highest local address configured on the interface.

    正确答案:A,C

  • 第19题：

    单选题
    After issuing the show interfaces terse command, you notice that the status of one interface is "up down". What does this indicate?"（）
    A

    Layer 1 on the interface is up but Layer 2 is down.

    B

    Layer 2 on the interface is up but Layer 3 has not been configured.

    C

    The interface is administratively up but the link status is down.

    D

    The interface is up but has been administratively turned off.


    正确答案： C
    解析： 暂无解析

  • 第20题：

    多选题
    Refer to the exhibit. Which three statements correctly describe Network Device A?（）
    A

    With a network wide mask of 255.255.255.128, each interface does not require an IP address.

    B

    With a network wide mask of 255.255.255.128, each interface does require an IP address on a unique IP subnet.

    C

    With a network wide mask of 255.255.255.0, must be a Layer 2 device for the PCs to communicate with each other.

    D

    With a network wide mask of 255.255.255.0, must be a Layer 3 device for the PCs to communicate with each other.

    E

    With a network wide mask of 255.255.254.0, each interface does not require an IP address.


    正确答案： C,A
    解析： 暂无解析

  • 第21题：

    单选题
    Which command is used to enable EtherChannel hashing for Layer 3 IP and Layer 4 port-based CEF？（）
    A

    mpls ip cef

    B

    port-channel ip cef

    C

    mpls ip port-channel cef

    D

    port-channel load balance

    E

    mpls ip load-balance

    F

    ip cef EtherChannel channel-id XOR L4

    G

    ip cef connection exchange


    正确答案： D
    解析： 暂无解析

  • 第22题：

    单选题
    A network administrator creates a layer 3 EtherChannel, bundling four interfaces into channel group 1. On what interface is the IP address configured?（）
    A

    the port-channel 1 interface

    B

    the highest number member interface

    C

    all member interfaces

    D

    the lowest number member interface


    正确答案： B
    解析： 暂无解析

  • 第23题：

    单选题
    What is the result of entering the command port-channel load-balance src-dst-ip on an EtherChannel link？ （）
    A

    Packets are distributed across the ports in the channel based on both the source and destination MAC addresses.

    B

    Packets are distributed across the ports in the channel based on both the source and destination IP addresses.

    C

    Packets are balanced across the ports in the channel based first on the source MAC address， then on the destination MAC address， then on the IP address.

    D

    Packets are distributed across the access ports in the channel based first on the source IP address and then the destination IP addresses.


    正确答案： D
    解析： 暂无解析

相关内容