A network administrator is troubleshooing an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to

题目

A network administrator is troubleshooing an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to be checked. What command will display the required information?（）

A. Router# show ip eigrp adjacency

B. Router# show ip eigrp topology

C. Router# show ip eigrp interfaces

D. Router# show ip eigrp neighbors

相似考题

1.A network administrator has configured source NAT, translating to an address that is on a locally connected subnet.The administrator sees the translation working, but traffic does not appear to come back.What is causing the problem?（）A. The host needs to open the telnet port.B. The host needs a route for the translated address.C. The administrator must use a proxy-arp policy for the translated address.D. The administrator must use a security policy, which will allow communication between the zones.

2.Refer to the exhibit. BigBids Incorporated is a worldwide auction provider. The network uses EIGRP as its routing protocol throughout the corporation. The network administrator does not understand the convergence of EIGRP. Using the output of the show ip eigrp topology all - links command, answer the administrator‘s questions.Which three networks is the router at 172.17.10.2 directly connected to?（）A. 172.17.0.0/30B. 172.17.1.0/24C. 172.17.2.0/24D. 172.17.3 .0/25E. 172.17.3.128/25F. 172.17.10.0/24

3.Refer to the exhibit. EIGRP had converged in AS 1 when the link between router R1 and R2 went down. The console on router R2 generated the following messages:*Mar 20 12:12:06: %DUAL - 5NBRCHANG E: IP - EIGRP 1: Neighbor 10.1.4.3 (Serial0) is down: stuck in active*Mar 20 12:15:23: %DUAL -3- SIA: Route 10.1.1.0/24 stuck - in - active state in IP - EIGRP 1.Cleaning up The network administrator issued the show ip eigrp topology active command on R2 to check the status of the EIGRP network.Which statement best describes the reason for the error messages?（）A. Incorrect bandwidth configuration on router R3 prevents R2 from establishing neighbor adjacency.B. Incorrect bandwidth configuration on router R 5 prevents R2 from establishing neighbor adjacency.C. Router R3 did not reply to the query about network 10.1.1.0/24 sent by router R2 .D. Router R5 did not reply to the query about network 10.1.1.0/24 sent by router R2 .

4.An administrator replaced a router with a switch. End users are able to access network shares butare not able to access the Internet. Which of the following is the BEST explanation why the usersare unable to access the Internet?（）A. Router routes traffic between different networks and a switch does notB. The new switch is faulty and needs to be replaced and configured correctlyC. The firewall needs to be setup to allow traffic to reach the InternetD. The switch needs to be setup to forward data traffic to the Internet

参考答案和解析
参考答案：D
更多“A network administrator is troubleshooing an EIGRP problem on a router and needs to confir ”相关问题

  • 第1题：

    Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）

    A. The no auto - summary command needs to be added under router eigrp 1

    B. The subnets keyword was not included in the redistribute command under router ospf 1

    C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router A

    D. The default - information originate command needs to be added under router ospf 1

    E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF


    参考答案：B

  • 第2题：

    After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:What information can you determine about this network?()

    A. The network is stable

    B. There is a flapping link or interface, and router C knows an alternate path to the network

    C. There is a flapping link or interf ace, and router C does not know an alternate path to the network

    D. EIGRP is not working correctly on router C

    E. There is not enough information to make a determination


    参考答案：B

  • 第3题：

    While troubleshooting a network problem,a technician discovers that the current copy of the Cisco IOS is outdated and needs to be updated.Which of the following commands would the technician issue to replace the Cisco router IOS with the newer version?（）

    A. Router#copy tftp flash

    B. Router(config)#restore flash

    C. Router(config)#repair flash

    D. Router#copy flash run

    E. Router>copy start flash

    F. Router#copy start flash


    参考答案：A

  • 第4题：

    A router learns about a remote network from EIGRP, OSPF, and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network（）。

    A.The router will use the static route.

    B.The router will use the OSPF route.

    C.The router will use the EIGRP route.

    D.The router will load balance and use all three routes.


    参考答案：A

  • 第5题：

    Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）

    • A、As numbers must be changed to match on all the routers.
    • B、Loopback interface must be configured so a DR is elected.
    • C、The no auto-summary command is needed on Router A and Router C.
    • D、Router B needs to have two network statements, one for each connected network.

    正确答案:A

  • 第6题：

    While troubleshooting a network problem,a technician discovers that the current copy of the Cisco IOS is outdated and needs to be updated.Which of the following commands would the technician issue to replace the Cisco router IOS with the newer version?（）

    • A、Router#copy tftp flash
    • B、Router(config)#restore flash
    • C、Router(config)#repair flash
    • D、Router#copy flash run
    • E、Router>copy start flash
    • F、Router#copy start flash

    正确答案:A

  • 第7题：

    A router leams about a remote network from EIGRP.OSPF. and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network?（）

    • A、The router will use the static route.
    • B、The router will use the OSPF route.
    • C、The route will use the EIGRP route.
    • D、The router will load balance and use all three routes.

    正确答案:A

  • 第8题：

    A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem? （）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0

    • A、The process id is configured improperly
    • B、The OSPF area is configured improperly
    • C、The network wildcard mask is configured improperly
    • D、The network number is configured improperly
    • E、The AS is configured improperly
    • F、The network subnet mask is configuerd improperly

    正确答案:C

  • 第9题：

    单选题
    A router learns about a remote network from EIGRP, OSPF, and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network（）。
    A

    The router will use the static route.

    B

    The router will use the OSPF route.

    C

    The router will use the EIGRP route.

    D

    The router will load balance and use all three routes.


    正确答案： B
    解析： 暂无解析

  • 第10题：

    单选题
    A network administrator is troubleshooing an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to be checked. What command will display the required information?（）
    A

    Router# show ip eigrp adjacency

    B

    Router# show ip eigrp topology

    C

    Router# show ip eigrp interfaces

    D

    Router# show ip eigrp neighbors


    正确答案： D
    解析： 暂无解析

  • 第11题：

    单选题
    A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（） Router(config)#router ospf 1 Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
    A

    The process id is configured improperly

    B

    The OSPF area is configured improperly

    C

    The network wildcard mask is configured improperly

    D

    The network number is configured improperly

    E

    The AS is configured improperly

    F

    The network subnet mask is configuerd improperly


    正确答案： F
    解析： 暂无解析

  • 第12题：

    单选题
    Refer to the exhibit. A network administrator configures a new router and enters the copy startup-config running-config on the router. The network administrator powers down the router and sets it up at a remote location. When the router starts, it enter the system configuration dialog as shown. What is the caust of the problem?（）
    A

    The network administrator faled to save the configuration.

    B

    The configuration register is set to 0x2100.

    C

    The boot system flash command is missing from the configuration.

    D

    The configuraiton register is set to 0x2102.

    E

    The router is configured with the boot system startup command.


    正确答案： A
    解析： 暂无解析

  • 第13题：

    Refer to the exhibit. Router B is performing bidirectional redistribution between EIGRP an d OSPF.The network 10.100.1.0/24 should not be reachable from the 10.100.9.0/24 network. However, it needs to be reachable from any network within the EIGRP domain. All other networks should be seen in both domains. Which change to router B would accom plish these goals?（）

    A. Under the EIGRP process, insert the distribute - list block_net_1 out ospf 1 command.

    B. Under the OSPF process, insert the distribute - list block_net_1 in serial1/0 command.

    C. Under the EIGRP process, insert the distribute - list block_net_1 in serial1/0 command.

    D. Under the OSPF process, insert the distribute - list block_net_1 out eigrp 1 command.


    参考答案：D

  • 第14题：

    After implementing EIGRP on your network, you issue the show ip eigrp traffic command on router C. The following output is shown:What can you conclude about this network? ()

    A. The network has been stable for at least the last 45 minutes

    B. There is a flapping link or interf ace, and router C knows an alternate path to the network

    C. There is a flapping link or interface, and router A does not know an alternate path to the network

    D. EIGRP is not working correctly on router C

    E. There is not enough information to make a determination


    参考答案：A

  • 第15题：

    The EIGRP configuration in the Glencoe router uses a single network statement.From the output shown in the graph would advertise these networks in EIGRP?()

    A.network 172.26.168.0 area 478

    B.network 172.26.0.0

    C.network 172.26.168.128 0.0.0.127

    D.network 172.26.168.128 area 478


    参考答案：B

  • 第16题：

    A network administrator needs to configure a serial link between the main office and a remote location. The router at the remote office is a non-Cisco router.How should the network administrator configure the serial interface of the main office router to make the connection?（）

    A.

    B.

    C.

    D.


    参考答案：B

  • 第17题：

    A router learns about a remote network from EIGRP, OSPF, and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network（）。

    • A、The router will use the static route.
    • B、The router will use the OSPF route.
    • C、The router will use the EIGRP route.
    • D、The router will load balance and use all three routes.

    正确答案:A

  • 第18题：

    The EIGRP configuration in the Glencoe router uses a single network statement.From the output shown in the graph would advertise these networks in EIGRP?（）

    • A、network 172.26.168.0 area 478
    • B、network 172.26.0.0
    • C、network 172.26.168.128 0.0.0.127
    • D、network 172.26.168.128 area 478

    正确答案:B

  • 第19题：

    A network administrator is troubleshooing an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to be checked. What command will display the required information?（）

    • A、Router# show ip eigrp adjacency
    • B、Router# show ip eigrp topology
    • C、Router# show ip eigrp interfaces
    • D、Router# show ip eigrp neighbors

    正确答案:D

  • 第20题：

    An administrator replaced a router with a switch. End users are able to access network shares butare not able to access the Internet. Which of the following is the BEST explanation why the usersare unable to access the Internet?（）

    • A、Router routes traffic between different networks and a switch does not
    • B、The new switch is faulty and needs to be replaced and configured correctly
    • C、The firewall needs to be setup to allow traffic to reach the Internet
    • D、The switch needs to be setup to forward data traffic to the Internet

    正确答案:A

  • 第21题：

    单选题
    Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）
    A

    As numbers must be changed to match on all the routers.

    B

    Loopback interface must be configured so a DR is elected.

    C

    The no auto-summary command is needed on Router A and Router C.

    D

    Router B needs to have two network statements, one for each connected network.


    正确答案： B
    解析： 暂无解析

  • 第22题：

    多选题
    Router R1 is configured as shown below: router eigrp 100 network 10.0.0.0 eigrp stub Based on the information shown above, which two types of routes will be advertised？（）
    A

    Receive - only

    B

    Stub

    C

    Static

    D

    Summary

    E

    Connected

    F

    Dynamic


    正确答案： B,A
    解析： 暂无解析

  • 第23题：

    单选题
    A router leams about a remote network from EIGRP.OSPF. and a static route. Assuming all routing protocols are using their default administrative distance, which route will the router use to forward data to the remote network?（）
    A

    The router will use the static route.

    B

    The router will use the OSPF route.

    C

    The route will use the EIGRP route.

    D

    The router will load balance and use all three routes.


    正确答案： C
    解析： 暂无解析

相关内容