Which command should you use to verify what networks are being routed by a given OSPF process()A.show ip ospfB.show ip routeC.show ip protocolD.show ip ospfdatabaseE.None of the other alternatives apply

第1题：

第2题：

You are troubleshooting an OSPF problem where external routes are not showing up in the OSPF database. Which two options a re valid checks that should be performed first to verify proper OSPF operation?（）

• A、Are the ASBRs trying to redistribute the external routes into a totally stubby area?
• B、Are the ABRs configured with stubby areas?
• C、Is the subnets keyword being used with the redistribution command?
• D、Is backbone area (area 0) contiguous?
• E、Is the CPU utilization of the routers high?

第3题：

You work as a Web Developer at Certkiller.com. You are in the process of creating a Webapplication using Microsoft ASP.NET 3.5.  You create a folder named Dark in the App_Themes folder of the Web application. You also addfour skin files to this folder. You have to make sure that the controls on a page have their appearances overridden by the control definitions defined in the skin files. What should you do？  Which Page directive should you use？（）

• A、You should use the page directive: <%@ Page StyleSheetTheme="App_Themes.Dark"/>
• B、You should use the page directive: <%@ Page Theme="App_Themes.Dark"/>
• C、You should use the page directive: <%@ Page Theme="Dark"/>
• D、You should use the page directive: <%@ Page StyleSheetTheme="Dark"/>

第4题：

Which two of these steps are minimum requirements to configure OSPFv3 under IPv6？（）

• A、Configure a routing process using the command ipv6 router ospf [process-id].
• B、Add the network statement for the interfaces on which OSPF will run.
• C、Configure OSPF on the interface that it will run on.
• D、Use the passive-interface command on the interfaces on which OSPF should not run.
• E、Enable routing.

第5题：

Which command should you use to verify what networks are being routed by a given OSPFprocess？（）

• A、show ip ospf
• B、show ip route
• C、show ip protocol
• D、show ip ospf database
• E、None of the other alternatives apply

第6题：

When troubleshooting an EIGRP connectivity problem, you notice that two connected EIGRP routers are not becoming EIGRP neighbors. A ping between the two routers was successful.What is the next thing that should be checked?（）

• A、Verify that the EIGRP hello and hold timers match exactly.
• B、Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP peer command.
• C、Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP traffic command.
• D、Verify that EIGRP is enabled for the appropriate networks on the local and neighboring router.

第7题：

While troubleshooting a network connectivity issue, you suspect that a router may be missing a route, or may be receiving bad routing information to a destination. What command should you issue to view the route that the router will use to reach a given destination?（）

• A、ping
• B、trace
• C、show ip route
• D、show interface
• E、show cdp neighbors

第8题：

第9题：

第10题：

第11题：

第12题：

第13题：

A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following: TK1(config)# router ospf 1 TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0 After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）

• A、The AS is not correctly configured
• B、The network subnet mask is incorrectly configured
• C、The network wildcard mask is configured incorrectly
• D、The network number is not correctly configured
• E、The process id is configured incorrectly
• F、None of the above

第14题：

Which IOS command would you use to find out which networks are routed by a particular OSPFprocess？（）

• A、show ospf
• B、show ip route
• C、show ip protocols
• D、show ip ospf database
• E、None of the other alternatives apply

第15题：

Which of the following networks would MOST likely require EGP routing?（）

• A、Networks that use OSPF in addition to static routes
• B、Networks with classless Internet domain routing
• C、Networks with multiple ISPs
• D、Networks that use encryption

第16题：

You have implemented mutua l route redistribution between OSPF and EIGRP on a border router. When checking the routing table on one of the EIGRP routers within the EIGRP routing domain, you are seeing some, but not all of the expected routes. What should you verify to troubleshoot this problem?（）

• A、The border router is using a proper seed metric for OSPF
• B、The border router is using a proper seed metric for EIGRP
• C、The administrative distance is set for OSPF and EIGRP
• D、The missing OSPF routes are present in the routing  table of the border router
• E、The subnet keyword on the border router in the redistribute OSPF command

第17题：

Which command should you use to verify what networks are being routed by a given OSPF process（）

• A、show ip ospf
• B、show ip route
• C、show ip protocol
• D、show ip ospfdatabase
• E、None of the other alternatives apply

第18题：

Which IOS command would you use to find out which networks are routed by a particular OSPF process（）

• A、show ip ospf
• B、show ip route
• C、show ip protocols
• D、show ip ospf database
• E、None of the other alternatives apply

第19题：

Which RMAN command do you use to verify that the RMAN repository information is synchronized with the actual files that exist on disk？（）

• A、LIST
• B、CHANGE
• C、CATALOG
• D、CROSSCHECK

第20题：

第21题：

第22题：

第23题：