A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,wha

题目

A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（）Router(config)router ospf 1Router(config-router)network 10.0.0.0 255.0.0.0 area 0

A. The process id is configured improperly

B. The OSPF area is configured improperly

C. The network wildcard mask is configured improperly

D. The network number is configured improperly

E. The AS is configured improperly

F. The network subnet mask is configuerd improperly

相似考题

1.某园区网采用OSPF路由协议，参与OSPF的网络地址是169.111.0.0/16 Cisco路由器的正确配置是A．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.0.0 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0B．Router (config) #router ospf 63 Router (config-router) # network 169.111.0.0 255.255.0.0 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0C．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.255.255 area 0 Router (config-router) #area 0 range 169.111.0.0 255.255.0.0D．Router (config) #router ospf 63 Router (config-router) #network 169.111.0.0 0.0.255.255 area 0 Router (config-router) #area 0 range 169.111.0.0 0.0.255.255

2.If all OSPF routers on a broadcast network have the same OSPF priority, what parameter is used to determine the new BDR at the time of a DR failure?()A. area IDB. router IDC. loopback addressD. IP address of interface on broadcast network

3.Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface.What command would make this router not use a DR, and dynamically discover OSPF neighbors?（）A. ip ospf network broadcastB. ip ospf network non - broadcastC. ip ospf network point - to - multipointD. ip ospf network point - to - multipoint non - broadcast

4.Why might the Ezonexam network administrator set the configuration register to 0x2142 on a 2600 series Cisco router?A．To boot the IOS from ROMB．To reset the console passwordC．To upload a new version of the configuration fileD．To upload a new version of the IOSE．To allow a new memory upgrade to be recognized by the router

参考答案和解析
参考答案：C
更多“A network administrator is trying to add a new router into an established OSPF network.The ”相关问题

  • 第1题：

    Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）

    A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcast

    B. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - point

    C. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3

    D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253


    参考答案：A, B, D

  • 第2题：

    Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0／24 to OSPF area 0?()

    A.Router(config)#router ospf 1

    B.Router(config)#router ospf 0

    C.Router(config)#router ospf area 0

    D.Router(config-router)#network 192.168.16.0 0.0.0.255 area 0

    E.Router(config-router)#network 192.168.16.0 0.0.0.255 0

    F.Router(config-router)#network 192.168.16.0 255.255.255.0 area 0


    参考答案：A, D

  • 第3题：

    Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）

    • A、TestKingRouter(config)# router ospf 0
    • B、TestKingRouter(config)# router ospf 1
    • C、TestKingRouter(config)# router ospf area 0
    • D、TestKingRouter(config)# network 192.168.16.0 0.0.0.255 0
    • E、TestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0
    • F、TestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0

    正确答案:B,E

  • 第4题：

    If all OSPF routers on a broadcast network have the same OSPF priority, what parameter is used to determine the new BDR at the time of a DR failure?（）

    • A、area ID
    • B、router ID
    • C、loopback address
    • D、IP address of interface on broadcast network

    正确答案:B

  • 第5题：

    A network administrator is troubleshooing an EIGRP problem on a router and needs to confirm the IP addresses of the devices with which the router has established adjacency. The retransmit interval and the queue counts for the adjacent routers also need to be checked. What command will display the required information?（）

    • A、Router# show ip eigrp adjacency
    • B、Router# show ip eigrp topology
    • C、Router# show ip eigrp interfaces
    • D、Router# show ip eigrp neighbors

    正确答案:D

  • 第6题：

    Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface. What command would make this router not use a DR, and dynamically discover OSPF neighbors?（）

    • A、ip ospf network broadcast
    • B、ip ospf network non - broadcast
    • C、ip ospf network point - to - multipoint
    • D、ip ospf network point - to - multipoint non - broadcast

    正确答案:C

  • 第7题：

    A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem? （）Router(config)#router ospf 1Router(config-router)#network 10.0.0.0 255.0.0.0 area 0

    • A、The process id is configured improperly
    • B、The OSPF area is configured improperly
    • C、The network wildcard mask is configured improperly
    • D、The network number is configured improperly
    • E、The AS is configured improperly
    • F、The network subnet mask is configuerd improperly

    正确答案:C

  • 第8题：

    多选题
    Which of the following OSPF commands, when used together, will put the network 192.168.10.0/24 into OSPF area 0?（）
    A

    Router(config-router)# network 192.168.10.0 0.0.0.255 0

    B

    Router(config-router)# network 192.168.10.0 0.0.0.255 area 0

    C

    Router(config-router)# network 192.168.10.0 255.255.255.0 area 0

    D

    Router(config)# router ospf 0

    E

    Router(config)# router ospf 1


    正确答案： C,E
    解析： 暂无解析

  • 第9题：

    多选题
    Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0？（）
    A

    Router（config）#router ospf 1

    B

    Router（config）#router ospf 0

    C

    Router（config）#router ospf area 0

    D

    Router（config-router）#network 192.168.16.0 0.0.0.255 area 0

    E

    Router（config-router）#network 192.168.16.0 0.0.0.255 0

    F

    Router（config-router）#network 192.168.16.0 255.255.255.0 area 0


    正确答案： F,D
    解析： 暂无解析

  • 第10题：

    单选题
    A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?（） Router(config)#router ospf 1 Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
    A

    The process id is configured improperly

    B

    The OSPF area is configured improperly

    C

    The network wildcard mask is configured improperly

    D

    The network number is configured improperly

    E

    The AS is configured improperly

    F

    The network subnet mask is configuerd improperly


    正确答案： F
    解析： 暂无解析

  • 第11题：

    多选题
    Which commands are required to properly configure a router to properly configure a router to run OSPFand to add network 192.168.16.0/24 to OSPF area 0？（）
    A

    Router（config）#router ospf 1

    B

    Router（config）#router ospf 0

    C

    Router（config）#router ospf  area 0

    D

    Router（config-router）#network 192.168.16.0 0.0.0.255 area 0

    E

    Router（config-router）#network 192.168.16.0 0.0.0.255 0

    F

    Router（config-router）#network 192.168.16.0 255.255.255.0 area 0


    正确答案： B,C
    解析： 暂无解析

  • 第12题：

    单选题
    Refer to the exhibit. A network administrator configures a new router and enters the copy startup-config running-config on the router. The network administrator powers down the router and sets it up at a remote location. When the router starts, it enter the system configuration dialog as shown. What is the caust of the problem?（）
    A

    The network administrator faled to save the configuration.

    B

    The configuration register is set to 0x2100.

    C

    The boot system flash command is missing from the configuration.

    D

    The configuraiton register is set to 0x2102.

    E

    The router is configured with the boot system startup command.


    正确答案： A
    解析： 暂无解析

  • 第13题：

    A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following:TK1(config) router ospf 1TK1(config-router) network 10.10.10.0 255.255.255.0 area 0After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）

    A. The AS is not correctly configured

    B. The network subnet mask is incorrectly configured

    C. The network wildcard mask is configured incorrectly

    D. The network number is not correctly configured

    E. The process id is configured incorrectly

    F. None of the above


    参考答案：C

  • 第14题：

    A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following: TK1(config)# router ospf 1 TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0 After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）

    • A、The AS is not correctly configured
    • B、The network subnet mask is incorrectly configured
    • C、The network wildcard mask is configured incorrectly
    • D、The network number is not correctly configured
    • E、The process id is configured incorrectly
    • F、None of the above

    正确答案:C

  • 第15题：

    Which commands are required to properly configure a router to properly configure a router to run OSPFand to add network 192.168.16.0/24 to OSPF area 0？（）

    • A、Router（config）#router ospf 1
    • B、Router（config）#router ospf 0
    • C、Router（config）#router ospf  area 0
    • D、Router（config-router）#network 192.168.16.0 0.0.0.255 area 0
    • E、Router（config-router）#network 192.168.16.0 0.0.0.255 0
    • F、Router（config-router）#network 192.168.16.0 255.255.255.0 area 0

    正确答案:A,D

  • 第16题：

    Which commands are required to properly configure a router to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）

    • A、Router(config)#router ospf 1
    • B、Router(config)#router ospf 0
    • C、Router(config)#router ospf area 0
    • D、Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
    • E、Router(config-router)#network 192.168.16.0 0.0.0.255 0
    • F、Router(config-router)#network 192.168.16.0 255.255.255.0 area 0

    正确答案:A,D

  • 第17题：

    Which of the following OSPF commands, when used together, will put the network 192.168.10.0/24 into OSPF area 0?（）

    • A、Router(config-router)# network 192.168.10.0 0.0.0.255 0
    • B、Router(config-router)# network 192.168.10.0 0.0.0.255 area 0
    • C、Router(config-router)# network 192.168.10.0 255.255.255.0 area 0
    • D、Router(config)# router ospf 0
    • E、Router(config)# router ospf 1

    正确答案:B,E

  • 第18题：

    Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）

    • A、Router(config)#router ospf 1
    • B、Router(config)#router ospf 0
    • C、Router(config)#router ospf area 0
    • D、Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
    • E、Router(config-router)#network 192.168.16.0 0.0.0.255 0
    • F、Router(config-router)#network 192.168.16.0 255.255.255.0 area 0

    正确答案:A,D

  • 第19题：

    什么命令序列将配置一个路由器运行OSPF，并添加网络10.1.1.0/24 area0？（）

    • A、router ospf area 0 network 10.1.1.0 255.255.255.0 area 0
    • B、router ospf network 10.1.1.0 0.0.0.255
    • C、router ospf 1 network 10.1.1.0 0.0.0.255 area 0
    • D、router ospf area 0 network 10.1.1.0 0.0.0.255 area 0
    • E、router ospf network 10.1.1.0 255.255.255.0 area 0
    • F、router ospf 1 network 10.1.1.0 0.0.0.255

    正确答案:D

  • 第20题：

    多选题
    Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）
    A

    TestKingRouter(config)# router ospf 0

    B

    TestKingRouter(config)# router ospf 1

    C

    TestKingRouter(config)# router ospf area 0

    D

    TestKingRouter(config)# network 192.168.16.0 0.0.0.255 0

    E

    TestKingRouter(config)# network 192.168.16.0 0.0.0.255 area 0

    F

    TestKingRouter(config)# network 192.168.16.0 255.255.255.0 area 0


    正确答案： A,D
    解析： 暂无解析

  • 第21题：

    单选题
    If all OSPF routers on a broadcast network have the same OSPF priority， what parameter is used to determine the new BDR at the time of a DR failure？（）
    A

     area ID

    B

     router ID

    C

     loopback address

    D

     IP address of interface on broadcast network


    正确答案： B
    解析： 暂无解析

  • 第22题：

    单选题
    You try to add a new router into the established Testking OSPF network. The networks attached to the new router do not appear in the routing tables of the other OSPF routers.The new router was configured for OSPF in the following way: Router(config)# router ospf 99 Router(config-if)# network 10.0.0.0 255.0.0.0 area 0 Based on this information, what is the most likely problem?（）
    A

    The process id is configured improperly.

    B

    The OSPF area is configured improperly.

    C

    The network wildcard mask is configured improperly.

    D

    The network number is configured improperly.

    E

    The AS is configured improperly.

    F

    The network subnet mask is configured improperly.

    G

    All of the above are likely problems.


    正确答案： C
    解析： 暂无解析

  • 第23题：

    多选题
    Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）
    A

    Router(config)#router ospf 1

    B

    Router(config)#router ospf 0

    C

    Router(config)#router ospf area 0

    D

    Router(config-router)#network 192.168.16.0 0.0.0.255 area 0

    E

    Router(config-router)#network 192.168.16.0 0.0.0.255 0

    F

    Router(config-router)#network 192.168.16.0 255.255.255.0 area 0


    正确答案： C,A
    解析： 暂无解析

  • 第24题：

    单选题
    A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following: TK1(config)# router ospf 1 TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0 After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）
    A

    The AS is not correctly configured

    B

    The network subnet mask is incorrectly configured

    C

    The network wildcard mask is configured incorrectly

    D

    The network number is not correctly configured

    E

    The process id is configured incorrectly

    F

    None of the above


    正确答案： E
    解析： 暂无解析

相关内容