Refer to the exhibit.What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN?()A.The number of collision domains would decrease.B.The number of collision domains would increase.C.The number of br
题目
A.The number of collision domains would decrease.
B.The number of collision domains would increase.
C.The number of broadcast domains would remain the same.
D.The number of collision domains would remain the same.
E. The number of broadcast domains would increase.
相似考题
更多“Refer to the exhibit.What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN?() ”相关问题
-
第1题：
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location？ （）
- A、The switch must be configured with an IP address,subnet mask,and default gateway.
- B、The switch must be connected to a router over a VLAN trunk.
- C、The switch must be reachable through a port connected to its management VLAN.
- D、The switch console port must be connected to the Ethernet LAN.
- E、The switch management VLAN must be created and have a membership of at least one switch port.
- F、The switch must be fully configured as an SNMP agent.
正确答案:A,C -
第2题：
An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）
- A、The switch must be configured with an IP address, subnet mask, and default gateway.
- B、The switch must be connected to a router over a VLAN trunk.
- C、The switch must be reachable through a port connected to its management VLAN.
- D、The switch console port must be connected to the Ethernet LAN.
- E、The switch management VLAN must be created and have a membership of at least one switch
正确答案:A,C -
第3题：
Refer to the output shown on switch SW1 below： VLAN 1 bridge priority set to 8192. VLAN 1 bridge max aging time set to 20.VLAN 1 bridge hello time set to 2. VLAN 1 bridge forward delay set to 15. Switch is now the root switch for active VLAN 1. What command would you enter to reproduce this output？
正确答案:set spantree root 1 -
第4题：
A customer has two Ethernet Switch Modules installed in an IBM BladeCenter Enterprise chassis. The modules were configured identically. The Ethernet module in bay one was inadvertenly reset to factory defaults. Which solution returns the module to the customer-specific configuration?（）
- A、Back up the configuration from Ethernet module in bay 2 and restore it to the module in Bay 1 using the switch CLI or Web interface
- B、Swap the modules, which will automatically resynch the settings stored in the Advanced Management Module
- C、Back up the configuration of the Ethernet module in bay one and restore it to the Ethernet module in bay two using the AMM
- D、Restore the configuration from NVRAM using the Switch Module Web interface
正确答案:A -
第5题：
Which two statements are true regarding an Ethernet collision domain?（）
- A、The likelihood of collisions occurring increases when a switch is used.
- B、The likelihood of collisions occurring increases when a hub is used.
- C、If a hub is used, the collision domain is limited to each device and the hub.
- D、If a switch is used, the collision domain is limited to each device and the switch.
正确答案:B,D -
第6题：
单选题Refer to the exhibit.All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?（）AThe access link needs to be configured in multiple VLANs.
BThe link between the switches is configured in the wrong VLAN.
CThe link between the switches needs to be configured as a trunk.
DVTP is not configured to carry VLAN information between the switches.
ESwitch IP addresses must be configured in order for traffic to be forwarded between the switches
正确答案： D解析： 暂无解析 -
第7题：
单选题A banking customer has two Ethernet Switch Modules installed in an IBM BCE chassis. The modules were configured identically. The Ethernet module in bay 1 was accidentally reset to factory defaults. Which solution returns the module to the customer-specific configuration? （）ARestore the configuration from NVRAM using the Switch Module Web interface
BBack up the configuration of the Ethernet module in bay 1 and restore it to the Ethernet module in bay 2 using the AMM
CSwap the modules, which will automatically resynch the settings stored in the Advanced Management Module
DBack up the configuration from Ethernet module in bay 2 and restore it to the module in Bay 1 using the switch CLI or Web interface
正确答案： C解析： 暂无解析 -
第8题：
单选题A project requires a new server to be set up with the ability to automatically fail over its Ethernet connection to a second connection if a network failure occurs. Which of the following provides greatest resiliency？（）ATwo switch ports will be needed on a switch， two Ethernet cables will be needed for the server each connecting to two different Ethernet cards， and one IP address will be needed.
BTwo switch ports will be needed on two different switches， two Ethernet cables will be needed for the server each connecting to two different Ethernet cards， and one IP address will be needed.
CTwo switch ports will be needed on two different switches， two Ethernet cables will be needed for the server each connecting to two different Ethernet cards， two different IP addresses will be needed.
DOne switch port will be needed on one switch， a splitter will be needed to split the connection， two ethernet cables will be needed for the server each connecting to two different Ethernet cards， and two different IP addresses will be needed.
正确答案： B解析： 暂无解析 -
第9题：
单选题A customer is purchasing a 12-way p5-570 to run light development workloads on eight AIX 5.3 partitions with two network adapters each. When the current network configuration was reviewed， it was discovered that they only have four Ethernet ports available on their network switch. Which of the following solutions would prevent them from having to buy another network switch or hub？（）AAdd two HMCs with two Ethernet adapters each and run EtherChannel for the original eight partitions.
BAdd two HMCs with two Ethernet adapters each and run Virtual Ethernet for the original eight partitions.
CAdd two hosting partitions with two Ethernet adapters each and run EtherChannel for the original eight partitions.
DAdd two hosting partitions with two Ethernet adapters each and run Virtual Ethernet for the original eight partitions.
正确答案： B解析： 暂无解析 -
第10题：
多选题An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location？ （）AThe switch must be configured with an IP address,subnet mask,and default gateway.
BThe switch must be connected to a router over a VLAN trunk.
CThe switch must be reachable through a port connected to its management VLAN.
DThe switch console port must be connected to the Ethernet LAN.
EThe switch management VLAN must be created and have a membership of at least one switch port.
FThe switch must be fully configured as an SNMP agent.
正确答案： B,D解析： 暂无解析 -
第11题：
多选题Which two statements are true regarding an Ethernet collision domain?（）AThe likelihood of collisions occurring increases when a switch is used.
BThe likelihood of collisions occurring increases when a hub is used.
CIf a hub is used, the collision domain is limited to each device and the hub.
DIf a switch is used, the collision domain is limited to each device and the switch.
正确答案： A,D解析： 暂无解析 -
第12题：
问答题Refer to the output shown on switch SW1 below： VLAN 1 bridge priority set to 8192. VLAN 1 bridge max aging time set to 20.VLAN 1 bridge hello time set to 2. VLAN 1 bridge forward delay set to 15. Switch is now the root switch for active VLAN 1. What command would you enter to reproduce this output？正确答案： set spantree root 1解析： 暂无解析 -
第13题：
You have just created a new VLAN on your network. What is one step that you should include in your VLAN-based implementation and verification plan？ （）
- A、Verify that trunked links are configured to allow the VLAN traffic.
- B、Verify that the switch is configured to allow for trunking on the switch ports.
- C、Verify that each switch port has the correct IP address space assigned to it for the new VLAN.
- D、Verify that different native VLANs exist between two switches for security purposes.
正确答案:A -
第14题：
A new switch is installed in the Testking network. This switch is to be configured sothat VLAN information will be automatically distributed to all the other Cisco Catalyst switches in the network. Which of the conditions below have to be met in order for this to occur?（）
- A、The switch that will share the VLAN information must be in the VTP Server mode.
- B、The switches must be in the same VTP domain.
- C、The switch that will share the VLAN information must be configured as the root bridge.
- D、The switches must be configured to use the same VTP version.
- E、The switches must be configured to use the same STP version.
- F、The switches must be configured to use the same type of ID tagging.
- G、The switches must be connected over VLAN trunks.
正确答案:A,B,F -
第15题：
A project requires a new server to be set up with the ability to automatically fail over its Ethernet connection to a second connection if a network failure occurs. Which of the following provides greatest resiliency？（）
- A、Two switch ports will be needed on a switch， two Ethernet cables will be needed for the server each connecting to two different Ethernet cards， and one IP address will be needed.
- B、Two switch ports will be needed on two different switches， two Ethernet cables will be needed for the server each connecting to two different Ethernet cards， and one IP address will be needed.
- C、Two switch ports will be needed on two different switches， two Ethernet cables will be needed for the server each connecting to two different Ethernet cards， two different IP addresses will be needed.
- D、One switch port will be needed on one switch， a splitter will be needed to split the connection， two ethernet cables will be needed for the server each connecting to two different Ethernet cards， and two different IP addresses will be needed.
正确答案:B -
第16题：
Which two statements are true regarding an Ethernet collision domain?（）
- A、If a switch is used, the collision domain includes all devices connected to the switch.
- B、If a hub is used, the collision domain includes all devices connected to the hub.
- C、If a hub is used, the collision domain is limited to each device and the hub.
- D、If a switch is used, the collision domain is limited to each device and the switch.
正确答案:B,D -
第17题：
多选题Refer to the exhibit.What two results would occur if the hub were to be replaced with a switch that is configured with one Ethernet VLAN?（）AThe number of collision domains would decrease.
BThe number of collision domains would increase.
CThe number of broadcast domains would remain the same.
DThe number of collision domains would remain the same.
EThe number of broadcast domains would increase.
正确答案： C,A解析： 暂无解析 -
第18题：
单选题A project requires a new server to be set up with the ability to automatically fail over its Ethernet connection to a second connection if a network failure occurs. Which of the following provides greatest resiliency？（）ATwo switch ports will be needed on a switch,two Ethernet cables will be needed for theserver each connecting to two different Ethernet cards,and one IP address will be needed
BTwo switch ports will be needed on two different switches two Ethernet cables will beneeded for the server each connecting to two different Ethernet cards,and one IP address will be needed
CTwo switch ports will be needed on two different switches,two Ethernet cables will be needed for the server each connecting to two different Ethernet cards,two different IP addresses will be needed
DOne switch port will be needed on one switch,a splitter will be needed to split the connection,two Ethernet cables will be needed for the server each connecting to two different Ethernet cards,and two different IP addresses will be needed
正确答案： C解析： 暂无解析 -
第19题：
多选题Refer to the exhibit. The two connected ports on the switch are not turning orange or green. What would be the most effective steps to troubleshoot this physical layer problem?（）AEnsure that the Ethernet encapsulations match on the interconnected router and switch ports.
BEnsure that cables A and B are straight-through cables.
CEnsure cable A is plugged into a trunk port.
DEnsure the switch has power.
EReboot all of the devices.
FReseat all cables.
正确答案： C,F解析： 暂无解析 -
第20题：
单选题You have just created a new VLAN on your network for inter-VLAN routing. What is one step that you should include in your VLAN-based implementation and verification plan？（）AVerify that different native VLANs exist between two switches for security purposes.
BVerify that the switch is configured to allow for trunking on the switch ports.
CVerify that each switch port has the proper IP address space assigned to it for the new VLAN.
DVerify that the VLAN virtual interface has been correctly created and enabled.
正确答案： B解析： 暂无解析 -
第21题：
单选题You have just created a new VLAN on your network. What is one step that you should include in your VLAN based implementation and verification plan？ （）AVerify that different native VLANs exist between two switches for security purposes.
BVerify that the VLAN was added on all switches with the use of the show vlan command.
CVerify that the switch is configured to allow for trunking on the switch ports.
DVerify that each switch port has the correct IP address space assigned to it for the new VLAN.
正确答案： D解析： 暂无解析 -
第22题：
多选题Which two statements are true regarding an Ethernet collision domain?（）AIf a switch is used, the collision domain is limited to each device and the switch.
BIf a hub is used, the collision domain is limited to each device and the hub.
CIf a hub is used, the collision domain includes all devices connected to the hub.
DIf a switch is used, the collision domain includes all devices connected to the switch.
正确答案： C,A解析： 暂无解析 -
第23题：
多选题An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? （）AThe switch must be configured with an IP address, subnet mask, and default gateway.
BThe switch must be connected to a router over a VLAN trunk.
CThe switch must be reachable through a port connected to its management VLAN.
DThe switch console port must be connected to the Ethernet LAN.
EThe switch management VLAN must be created and have a membership of at least one switch
正确答案： E,B解析： 暂无解析