A network administrator needs to force a high-performance switch that is located in the MDF to become the root bridge for a redundant path switched network. What can be done to ensure that this switch assumes the role as root bridge（）。A.Establish a direct

题目

A network administrator needs to force a high-performance switch that is located in the MDF to become the root bridge for a redundant path switched network. What can be done to ensure that this switch assumes the role as root bridge（）。

A.Establish a direct link from the switch to all other switches in the network.

B.Assign the switch a higher MAC address than the other switches in the network have.

C.Configure the switch so that it has a lower priority than other switches in the network.

D.Configure the switch for full-duplex operation and configure the other switches for half-duplex operation.

E.Connect the switch directly to the MDF router, which will force the switch to assume the role of root bridge.

相似考题

1.The network administrator has configured port security on a Ezonexam switch. Why would a network administrator configure port security on this Ezonexam device?A．To prevent unauthorized hosts from getting access to the LANB．To limit the number of Layer 2 broadcasts on a particular switch portC．To prevent unauthorized Telnet or SSH access to a switch portD．To prevent the IP and MAC address of the switch and associated portsE．None of the above

2.An administrator replaced a router with a switch. End users are able to access network shares butare not able to access the Internet. Which of the following is the BEST explanation why the usersare unable to access the Internet?（）A. Router routes traffic between different networks and a switch does notB. The new switch is faulty and needs to be replaced and configured correctlyC. The firewall needs to be setup to allow traffic to reach the InternetD. The switch needs to be setup to forward data traffic to the Internet

3.The network administrator has just finished installing a new 10/100/1000 switch, but receives reports from the server administrator that servers connected to the new switch seem to be experiencing slow LAN connections. The network administrator checks the port connecting the new switch to the core switch and sees the following information:Which of the following is the MOST likely cause of the slow connections?（）A. The servers have not had VLAN tagging enabled on their NICs.B. Speed and duplex have not been set.C. VLAN tagging was not set on the trunk.D. The servers have been connected with CAT5 cable.

4.The Ezonexam network administrator needs to verify that switch interface 0/5 has been assigned to the Marketing VLA.N. Which command will accomplish this task?A. Show vlanB. Show mac-address-tableC. Show vtp statusD. show spanning-tree rootE. show ip interface briefF. None of the above

更多“A network administrator needs to force a high－performance switch that is located in the MD ”相关问题

  • 第1题：

    The Ezonexam network administrator needs to a switch named VE1 to become the root bridge for a redundant path switched network. What can be done to ensure that VE1 will always assume the role as the root bridge?

    A．Assign the switch a higher MAC address than the other switches in the network have

    B．Establish a direct link from the switch to all other switches in the network

    C．Configure the switch full-duplex operation and configure the other switches for half-duplex operation

    D．Configure the switch so that it has lower priority than other switches in the network

    E．None of the above


    正确答案：D

  • 第2题：

    A network administrator needs to verify that switch interface 0／5 has been assigned to the Sales VLA.N. Which command will accomplish this task?()

    A. Show vlan

    B. Show mac-address-table

    C. Show vtp status

    D. show spanning-tree root

    E. show ip interface brief


    参考答案：A

  • 第3题：

    A network administrator needs to verify that switch interface 0/5 has been assigned to the Sales VLA.N. Which command will accomplish this task?（）

    • A、Show vlan
    • B、Show mac-address-table
    • C、Show vtp status
    • D、show spanning-tree root
    • E、show ip interface brief

    正确答案:A

  • 第4题：

    A network administrator needs to configure port security on a switch.which two statements are true?（）

    • A、The network administrator can apply port security to dynamic access ports
    • B、The network administrator can configure static secure or sticky secure mac addresses in the voice vlan.
    • C、The sticky learning feature allows the addition of dynamically learned addresses to the running configuration.
    • D、The network administrator can apply port security to EtherChannels.
    • E、When dynamic mac address learning is enabled on an interface,the switch can learn new addresses,up to the maximum defined.

    正确答案:C,E

  • 第5题：

    A network administrator needs to force a high-performance switch that is located in the MDF to become the root bridge for a redundant path switched network. What can be done to ensure that this switch assumes the role as root bridge（）。

    • A、Establish a direct link from the switch to all other switches in the network.
    • B、Assign the switch a higher MAC address than the other switches in the network have.
    • C、Configure the switch so that it has a lower priority than other switches in the network.
    • D、Configure the switch for full-duplex operation and configure the other switches for half-duplex operation.
    • E、Connect the switch directly to the MDF router, which will force the switch to assume the role of root bridge.

    正确答案:C

  • 第6题：

    The Company network administrator needs to enable VTP pruning within the Company network. What action should a network administrator take to enable VTP pruning on an entire management  domain？（）

    • A、Enable VTP pruning on any switch in the management domain
    • B、Enable VTP pruning on any client switch in the domain
    • C、Enable VTP pruning on a VTP server in the management domain
    • D、Enable VTP pruning on every switch in the domain
    • E、None of the other alternatives apply

    正确答案:C

  • 第7题：

    A network administrator needs to add an additional connection to a room. The administrator adds a new Ethernet switch and must connect it to an existing switch. Which cable type should be used to connect the two switches?（）

    • A、CAT3 cable
    • B、Serial cable
    • C、Crossover cable
    • D、Rollover cable

    正确答案:C

  • 第8题：

    A technician needs to add network capacity. However, when plugging a second switch into the first switch, there is no link light. Which of the following is the cause of this situation?（）

    • A、The switches are not stackable
    • B、The cable was not wired using 568A
    • C、The cable needs to be a crossover cable
    • D、The switches have IGMP snooping enabled

    正确答案:C

  • 第9题：

    单选题
    An administrator has a malfunctioning uninterruptible power supply （UPS）. Which of the following is the MOST likely cause of the problem？（）
    A

     Battery needs to be replaced

    B

     Light switch is turned off

    C

     Smart cable is disconnected

    D

     UPS needs a firmware update


    正确答案： A
    解析： 暂无解析

  • 第10题：

    单选题
    Refer to the exhibit.The network administrator normally establishes a telnet session with the switch from host A.However,host A is unavailable.The administrator′s attempt to the switch from host B fails,but pings to the other two hosts are successful.what is the issue?（）
    A

    Host B and the switch need to be in the same subnet.

    B

    The switch needs and appropriate default gateway assigned.

    C

    The switch interface connected to the router is down.

    D

    Host B need to be assigned an IP address in vlan 1.

    E

    The switch interfaces need the appropriate IP addresses assigned.


    正确答案： E
    解析： 暂无解析

  • 第11题：

    单选题
    A network administrator needs to verify that switch interface 0/5 has been assigned to the Sales VLA.N. Which command will accomplish this task?（）
    A

    Show vlan

    B

    Show mac-address-table

    C

    Show vtp status

    D

    show spanning-tree root

    E

    show ip interface brief


    正确答案： C
    解析： 暂无解析

  • 第12题：

    单选题
    As a network administrator, you have configured a Catalyst 6500 Series Switch with redundant supervisor engine in a CIS network. What is the result of issuing the redundancy force-switchover command on that switch?（）
    A

    Automatic switchover from active to standby on primary supervisor failure

    B

    Reset of the primary supervisor.

    C

    Manual switchover from active to standby supervisor

    D

    Manual switchover from standby to active supervisor


    正确答案： D
    解析： 暂无解析

  • 第13题：

    As a network administrator, you have configured a Catalyst 6500 Series Switch with redundant supervisor engine in a CIS network. What is the result of issuing the redundancy force-switchover command on that switch?（）

    A. Automatic switchover from active to standby on primary supervisor failure

    B. Reset of the primary supervisor.

    C. Manual switchover from active to standby supervisor

    D. Manual switchover from standby to active supervisor


    参考答案：C

  • 第14题：

    Refer to the exhibit.The network administrator normally establishes a telnet session with the switch from host A.However,host A is unavailable.The administrator′s attempt to the switch from host B fails,but pings to the other two hosts are successful.what is the issue?（）

    A.Host B and the switch need to be in the same subnet.

    B.The switch needs and appropriate default gateway assigned.

    C.The switch interface connected to the router is down.

    D.Host B need to be assigned an IP address in vlan 1.

    E.The switch interfaces need the appropriate IP addresses assigned.


    参考答案：B

  • 第15题：

    A network administrator needs to configure port security on a switch.which two statements are true？（）

    • A、The network administrator can apply port security to dynamic access ports
    • B、The network administrator can configure static secure or sticky secure mac addresses in the voice vlan.
    • C、The sticky learning feature allows the addition of dynamically learned addresses to the runningconfiguration.
    • D、The network administrator can apply port security to EtherChannels.
    • E、When dynamic mac address learning is enabled on an interface，the switch can learn new addresses，up to the maximum defined.

    正确答案:C,E

  • 第16题：

    The network administrator has discovered that the power supply has failed on a switch in the company LAN and that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 2950 series switch.What must be done to ensure that this new switch becomes the root bridge on the network?（）

    • A、One router is running RIPv1.
    • B、RIP neighbor is 224.0.0.9.
    • C、The network contains a loop.
    • D、Network 10.10.1.0 is reachable.

    正确答案:A

  • 第17题：

    Before inserting a new switch in the network，the network administrator checks that the VTP domain name is correct，the VTP mode is set to server， and revision is lower than the switches in the network. The administrator then configures interfaces and trunks，erases existing VLANs，and connects the switch to the network. Following that procedure，there is no connectivity in the network. What is a possible cause of this problem？（）

    • A、Because the configuration revision of the new switches is lower than the rest of the network， it can change the VLAN database of the other switches.
    • B、As a VTP server， the new switch deleted all VLANs of the network.
    • C、Erasing VLANs increases the VTP configuration revision.
    • D、Since the configuration revision of the network is higher than the new switch， the VLAN database was automatically synchronized.

    正确答案:C

  • 第18题：

    You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）

    • A、The switch name must match the workgroup name of the local network.
    • B、The switch must be configured with an IP address and default gateway.
    • C、The remote workstations must have access to the management VLAN of the switch.
    • D、CDP must be enabled on the switch so that it can be located by other devices on the network.

    正确答案:B,C

  • 第19题：

    An administrator replaced a router with a switch. End users are able to access network shares butare not able to access the Internet. Which of the following is the BEST explanation why the usersare unable to access the Internet?（）

    • A、Router routes traffic between different networks and a switch does not
    • B、The new switch is faulty and needs to be replaced and configured correctly
    • C、The firewall needs to be setup to allow traffic to reach the Internet
    • D、The switch needs to be setup to forward data traffic to the Internet

    正确答案:A

  • 第20题：

    An administrator has a malfunctioning uninterruptible power supply (UPS). Which of the following is the MOST likely cause of the problem?（）

    • A、Battery needs to be replaced
    • B、Light switch is turned off
    • C、Smart cable is disconnected
    • D、UPS needs a firmware update

    正确答案:A

  • 第21题：

    多选题
    You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）
    A

    The switch name must match the workgroup name of the local network.

    B

    The switch must be configured with an IP address and default gateway.

    C

    The remote workstations must have access to the management VLAN of the switch.

    D

    CDP must be enabled on the switch so that it can be located by other devices on the network.


    正确答案： D,B
    解析： 暂无解析

  • 第22题：

    单选题
    A technician needs to add network capacity. However, when plugging a second switch into the first switch, there is no link light. Which of the following is the cause of this situation?（）
    A

    The switches are not stackable

    B

    The cable was not wired using 568A

    C

    The cable needs to be a crossover cable

    D

    The switches have IGMP snooping enabled


    正确答案： D
    解析： 暂无解析

  • 第23题：

    单选题
    An administrator has a single 14U rack.  The administrator needs to install fifteen servers； rack-mounted redundant uninterruptible power supplies （UPSs）， a network switch， and a KVM.  Which of the following server types would be BEST suited for this scenario？（）
    A

    Blade servers

    B

    Rackmount servers

    C

    Tower servers

    D

    Web servers


    正确答案： B
    解析： 暂无解析

  • 第24题：

    单选题
    The Company network administrator needs to enable VTP pruning within the Company network. What action should a network administrator take to enable VTP pruning on an entire management  domain？（）
    A

    Enable VTP pruning on any switch in the management domain

    B

    Enable VTP pruning on any client switch in the domain

    C

    Enable VTP pruning on a VTP server in the management domain

    D

    Enable VTP pruning on every switch in the domain

    E

    None of the other alternatives apply


    正确答案： C
    解析： 暂无解析

相关内容