单选题In which of the following locations would a technician set the LBA mode for a hard drive？（）A Jumper SettingsB Disk ManagerC Device ManagerD System BIOS

题目
单选题
In which of the following locations would a technician set the LBA mode for a hard drive？（）
A

Jumper Settings

B

Disk Manager

C

Device Manager

D

System BIOS

相似考题

1.A technician has lost a necessary jumper for a new hard drive that must be installed immediately.Which of the following is the BEST solution?()A. Use a jumper from the motherboard where the new drive is going to be installed.B. Use a jumper from a hard drive that is no longer functioning.C. Contact the manufacturer of the new hard drive and have a replacement jumper shipped immediately.D. The new hard drive must be replaced

2.A technician receives an error message ‘inaccessible boot device’ on their monitor. Which of thefollowing components is causing the issue?()A. Hard disk drive failureB. NTLDR file is missingC. BIOS is corruptedD. System board failure

3.A technician has installed a secondary hard drive for a computer. However, the hard drive is not appearing under My Computer. The disk is receiving power, and appeared on the POST when Windows started.Which of the following Windows utilities would help configure the new hard disk?（）A. Disk ManagementB. Services and ApplicationsC. Removable StorageD. Device Manager

4.A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller.Which of the following is the MOST likely cause of the problem?（）A. Both hard drives have the master jumper in place.B. One hard drive is set as master and the other slave.C. The hard drive data cable is reversed.D. Both hard drives have the cable select jumper in place.

更多“单选题In which of the following locations would a technician set the LBA mode for a hard drive？（）A Jumper SettingsB Disk ManagerC Device ManagerD System BIOS”相关问题

  • 第1题：

    A technician installs a CD-RW drive with a feature that enables the drive to write labels directly onto the disk. The computer will burn disks but will not write labels. Which of the following should the technician do NEXT?（）

    • A、Reboot the computer
    • B、Remove the drive and reinstall
    • C、Install the device driver
    • D、Flash the BIOS

    正确答案:C

  • 第2题：

    Which of the following system utilities would be used to change a drive type from dynamic tobasic?（）

    • A、System Partition Manager
    • B、NTBACKUP
    • C、Device Manager
    • D、Disk Management

    正确答案:D

  • 第3题：

    In which of the following locations can Mike, a technician, configure and format a newly installed hard drive so that it is accessible to the user?（）

    • A、My Computer
    • B、Disk Manager
    • C、Device Manager
    • D、Control Panel

    正确答案:B

  • 第4题：

    In which of the following locations would a technician set the LBA mode for a hard drive？（）

    • A、Jumper Settings
    • B、Disk Manager
    • C、Device Manager
    • D、System BIOS

    正确答案:D

  • 第5题：

    A user requires more storage space on their computer. After a technician installs a second IDE drive in the computer, the system will not recognize that there are any hard drives installed. Which of the following is the MOST likely cause of the problem?（）

    • A、The second hard drive has not been formatted for NTFS.
    • B、The jumpers on both drives are set to the cable select position.
    • C、The jumper on the first drive is set to master and the second is set to slave.
    • D、The jumpers on both drives are set to the master position.

    正确答案:D

  • 第6题：

    A technician has installed a secondary hard drive for a computer. However, the hard drive is not appearing under My Computer. The disk is receiving power, and appeared on the POST when Windows started. Which of the following Windows utilities would help configure the new hard disk?（）

    • A、Disk Management
    • B、Services and Applications
    • C、Removable Storage
    • D、Device Manager

    正确答案:A

  • 第7题：

    Which of the following utilities will a technician use to determine how many partitions a hard drive has?（）

    • A、Administrator Tools
    • B、Disk Management
    • C、Device Manager
    • D、Computer Management

    正确答案:B

  • 第8题：

    A technician installs a SATA controller card and moves the hard drive cable from the system board to the SATA controller. The system POSTs and the controller BIOS recognizes the hard drive but does not boot to the hard drive and start Windows. Which of the following is the MOST likely cause of the problem？（）

    • A、Windows cannot be booted from a controller card.
    • B、The hard drive must have Windows reinstalled because a new controller card was installed.
    • C、The SATA controller card was not set as a boot device in the computer BIOS.
    • D、The new controller must have the correct jumper settings for Windows mode.

    正确答案:C

  • 第9题：

    单选题
    A technician has installed a secondary hard drive for a computer. However, the hard drive is not appearing under My Computer. The disk is receiving power, and appeared on the POST when Windows started. Which of the following Windows utilities would help configure the new hard disk?（）
    A

    Disk Management

    B

    Services and Applications

    C

    Removable Storage

    D

    Device Manager


    正确答案： B
    解析： 暂无解析

  • 第10题：

    单选题
    Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）
    A

    The new drive’s jumper is set for master.

    B

    The new drive is connected to the secondary bus as a slave drive.

    C

    Both drives’ jumpers are set for cable select.

    D

    The old drive’s jumper is set for master and the new drive is set for slave.


    正确答案： A
    解析： 暂无解析

  • 第11题：

    单选题
    A technician has lost a necessary jumper for a new hard drive that must be installed immediately.Which of the following is the BEST solution?（）
    A

    Use a jumper from the motherboard where the new drive is going to be installed.

    B

    Use a jumper from a hard drive that is no longer functioning.

    C

    Contact the manufacturer of the new hard drive and have a replacement jumper shipped immediately.

    D

    The new hard drive must be replaced


    正确答案： A
    解析： 暂无解析

  • 第12题：

    单选题
    A technician installs a SATA controller card and moves the hard drive cable from the system board to the SATA controller. The system POSTs and the controller BIOS recognizes the hard drive but does not boot to the hard drive and start Windows. Which of the following is the MOST likely cause of the problem？（）
    A

    Windows cannot be booted from a controller card.

    B

    The hard drive must have Windows reinstalled because a new controller card was installed.

    C

    The SATA controller card was not set as a boot device in the computer BIOS.

    D

    The new controller must have the correct jumper settings for Windows mode.


    正确答案： B
    解析： 暂无解析

  • 第13题：

    A technician has lost a necessary jumper for a new hard drive that must be installed immediately.Which of the following is the BEST solution?（）

    • A、Use a jumper from the motherboard where the new drive is going to be installed.
    • B、Use a jumper from a hard drive that is no longer functioning.
    • C、Contact the manufacturer of the new hard drive and have a replacement jumper shipped immediately.
    • D、The new hard drive must be replaced

    正确答案:B

  • 第14题：

    A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller. Which of the following is the MOST likely cause of the problem?（）

    • A、Both hard drives have the master jumper in place.
    • B、One hard drive is set as master and the other slave.
    • C、The hard drive data cable is reversed.
    • D、Both hard drives have the cable select jumper in place.

    正确答案:A

  • 第15题：

    If a technician needs to convert a hard drive from Basic to Dynamic, which of the following utilities would the technician use?（）

    • A、Add Hardware Wizard
    • B、Device Manager
    • C、Computer Management
    • D、Disk Management

    正确答案:D

  • 第16题：

    Which of the following locations would a technician use to add a Windows 7 computer to adomain?（）

    • A、System Properties
    • B、Windows Defender
    • C、Network and Sharing Center
    • D、Device Manager

    正确答案:A

  • 第17题：

    A technician wants to create a spanned volume on a set of hard drives. Which of the following tools will identify if the drives will support a spanned volume?（）

    • A、System Information
    • B、Disk Management
    • C、Device Manager
    • D、Task Manager

    正确答案:B

  • 第18题：

    Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）

    • A、The new drive’s jumper is set for master.
    • B、The new drive is connected to the secondary bus as a slave drive.
    • C、Both drives’ jumpers are set for cable select.
    • D、The old drive’s jumper is set for master and the new drive is set for slave.

    正确答案:A

  • 第19题：

    A technician receives an error message ‘inaccessible boot device’ on their monitor. Which of thefollowing components is causing the issue?（）

    • A、Hard disk drive failure
    • B、NTLDR file is missing
    • C、BIOS is corrupted
    • D、System board failure

    正确答案:A

  • 第20题：

    单选题
    A technician installs a CD-RW drive with a feature that enables the drive to write labels directly onto the disk. The computer will burn disks but will not write labels. Which of the following should the technician do NEXT?（）
    A

    Reboot the computer

    B

    Remove the drive and reinstall

    C

    Install the device driver

    D

    Flash the BIOS


    正确答案： D
    解析： 暂无解析

  • 第21题：

    单选题
    In which of the following locations would a technician set the LBA mode for a hard drive？（）
    A

    Jumper Settings

    B

    Disk Manager

    C

    Device Manager

    D

    System BIOS


    正确答案： D
    解析： 暂无解析

  • 第22题：

    单选题
    A user requires more storage space on their computer. After a technician installs a second IDE drive in the computer, the system will not recognize that there are any hard drives installed. Which of the following is the MOST likely cause of the problem?（）
    A

    The second hard drive has not been formatted for NTFS.

    B

    The jumpers on both drives are set to the cable select position.

    C

    The jumper on the first drive is set to master and the second is set to slave.

    D

    The jumpers on both drives are set to the master position.


    正确答案： B
    解析： 暂无解析

  • 第23题：

    单选题
    On which of the following hard drive types must Bob, a technician, change the jumper setting to match the motherboard/cabling combination?（）
    A

    SATA

    B

    eSATA

    C

    Solid state

    D

    PATA


    正确答案： C
    解析： 暂无解析

  • 第24题：

    单选题
    A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller. Which of the following is the MOST likely cause of the problem?（）
    A

    Both hard drives have the master jumper in place.

    B

    One hard drive is set as master and the other slave.

    C

    The hard drive data cable is reversed.

    D

    Both hard drives have the cable select jumper in place.


    正确答案： C
    解析： 暂无解析

相关内容