单选题The customer brings their mini-tower and a new DVD/RW drive they want installed. The technician finds a second hard drive in an empty 5.25 bay connected to the secondary bus and jumpered as a slave. The ribbon cable will not stretch from the primary ha

题目
单选题
The customer brings their mini-tower and a new DVD/RW drive they want installed. The technician finds a second hard drive in an empty 5.25 bay connected to the secondary bus and jumpered as a slave. The ribbon cable will not stretch from the primary hard drive to the open 5.25 inch bay. Which of the following is the BEST solution?（）
A

Connect the new DVD drive as the primary on the secondary bus and leave the old CD drive disconnected.

B

Move the secondary hard drive next to the primary hard drive and connect to the primary bus. Connect the new DVD drive as the slave on the secondary bus.

C

Move the secondary hard drive from the secondary to the primary bus and then reformat the hard drive after rebooting then reassign the drive letters in disk management prior to installing the new DVD drive on the secondary bus.

D

Move the secondary hard drive to the bay and then connect it to the primary bus. Connect themini-tower and the new DVD drive as the master on the secondary bus.

相似考题

1.A technician has lost a necessary jumper for a new hard drive that must be installed immediately.Which of the following is the BEST solution?()A. Use a jumper from the motherboard where the new drive is going to be installed.B. Use a jumper from a hard drive that is no longer functioning.C. Contact the manufacturer of the new hard drive and have a replacement jumper shipped immediately.D. The new hard drive must be replaced

2.After installing a new hard drive into a server for the purpose of mirroring the data from the first drive to the second one， the server displays an “operating system not found” error. Which of the following should the technician do to boot the server from the original drive？（）A、Replace the second drive with a hot swappable one.B、Swap the drive boot order in the BIOSC、Make the second disk active under the disk management tool.D、Rebuild the array using the hardware RAID tool at boot.

3. The customer brings their mini-tower and a new DVD/RW drive they want installed. The technician finds a second hard drive in an empty 5.25 bay connected to the secondary bus and jumpered as a slave. The ribbon cable will not stretch from the primary hard drive to the open 5.25 inch bay. Which of the following is the BEST solution?（）A、Connect the new DVD drive as the primary on the secondary bus and leave the old CD drive disconnected.B、Move the secondary hard drive next to the primary hard drive and connect to the primary bus. Connect the new DVD drive as the slave on the secondary bus.C、Move the secondary hard drive from the secondary to the primary bus and then reformat the hard drive after rebooting then reassign the drive letters in disk management prior to installing the new DVD drive on the secondary bus.D、Move the secondary hard drive to the bay and then connect it to the primary bus. Connect themini-tower and the new DVD drive as the master on the secondary bus.

4.A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller.Which of the following is the MOST likely cause of the problem?（）A. Both hard drives have the master jumper in place.B. One hard drive is set as master and the other slave.C. The hard drive data cable is reversed.D. Both hard drives have the cable select jumper in place.

更多“单选题The customer brings their mini-tower and a new DVD/RW drive they want installed. The technician finds a second hard drive in an empty 5.25 bay connected to the secondary bus and jumpered as a slave. The ribbon cable will not stretch from the primary ha”相关问题

  • 第1题：

    A technician has lost a necessary jumper for a new hard drive that must be installed immediately.Which of the following is the BEST solution?（）

    • A、Use a jumper from the motherboard where the new drive is going to be installed.
    • B、Use a jumper from a hard drive that is no longer functioning.
    • C、Contact the manufacturer of the new hard drive and have a replacement jumper shipped immediately.
    • D、The new hard drive must be replaced

    正确答案:B

  • 第2题：

    A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller. Which of the following is the MOST likely cause of the problem?（）

    • A、Both hard drives have the master jumper in place.
    • B、One hard drive is set as master and the other slave.
    • C、The hard drive data cable is reversed.
    • D、Both hard drives have the cable select jumper in place.

    正确答案:A

  • 第3题：

    Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）

    • A、The new drive’s jumper is set for master.
    • B、The new drive is connected to the secondary bus as a slave drive.
    • C、Both drives’ jumpers are set for cable select.
    • D、The old drive’s jumper is set for master and the new drive is set for slave.

    正确答案:A

  • 第4题：

    A user has recently added a second IDE CD-RW drive to a machine in addition to the primary DVD-ROM drive. The drive opens and closes; however, they do not see it show up in Windows. Which of the following is the MOST likely cause?（）

    • A、The drive jumper settings are incorrect.
    • B、The drive is not receiving power from PSU.
    • C、Windows only supports one optical drive.
    • D、The user connected the drive with a SATA cable.

    正确答案:A

  • 第5题：

    A defective CD-ROM drive is replaced with a new CD-ROM drive. The new CD-ROM drive is able to read any CD that it accesses， but music CDs do not play music. What is the MOST likely cause of this problem？（）

    • A、The audio cable is not connected to the drive.
    • B、The ribbon cable is not connected.
    • C、The power cable is not connected.
    • D、The CD-ROM drivers are not installed.

    正确答案:A

  • 第6题：

    单选题
    A technician has installed a secondary hard drive for a computer. However, the hard drive is not appearing under My Computer. The disk is receiving power, and appeared on the POST when Windows started. Which of the following Windows utilities would help configure the new hard disk?（）
    A

    Disk Management

    B

    Services and Applications

    C

    Removable Storage

    D

    Device Manager


    正确答案： B
    解析： 暂无解析

  • 第7题：

    单选题
    Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）
    A

    The new drive’s jumper is set for master.

    B

    The new drive is connected to the secondary bus as a slave drive.

    C

    Both drives’ jumpers are set for cable select.

    D

    The old drive’s jumper is set for master and the new drive is set for slave.


    正确答案： A
    解析： 暂无解析

  • 第8题：

    单选题
    A client purchased a new internal hard drive to act as a second drive on a legacy machine. When the client attempts to install the drive, the cable connector on the new drive is not compatible with the available IDE cables. It is determined that the client has purchased a SATA hard drive. Which of the following would the technician recommend as the BEST solution to this situation?（）
    A

    Have the client purchase a SATA compatible system board.

    B

    Have the client purchase a SATA to IDE conversion kit.

    C

    Have the client return the drive and purchase an IDE compatible drive.

    D

    Have the client purchase a SCSI to SATA conversion kit.


    正确答案： C
    解析： 暂无解析

  • 第9题：

    单选题
    A technician has lost a necessary jumper for a new hard drive that must be installed immediately.Which of the following is the BEST solution?（）
    A

    Use a jumper from the motherboard where the new drive is going to be installed.

    B

    Use a jumper from a hard drive that is no longer functioning.

    C

    Contact the manufacturer of the new hard drive and have a replacement jumper shipped immediately.

    D

    The new hard drive must be replaced


    正确答案： A
    解析： 暂无解析

  • 第10题：

    单选题
    After installing a new hard drive into a server for the purpose of mirroring the data from the first drive to the second one， the server displays an “operating system not found” error. Which of the following should the technician do to boot the server from the original drive？（）
    A

    Replace the second drive with a hot swappable one.

    B

    Swap the drive boot order in the BIOS

    C

    Make the second disk active under the disk management tool.

    D

    Rebuild the array using the hardware RAID tool at boot.


    正确答案： C
    解析： 暂无解析

  • 第11题：

    单选题
    A technician installs a SATA controller card and moves the hard drive cable from the system board to the SATA controller. The system POSTs and the controller BIOS recognizes the hard drive but does not boot to the hard drive and start Windows. Which of the following is the MOST likely cause of the problem？（）
    A

    Windows cannot be booted from a controller card.

    B

    The hard drive must have Windows reinstalled because a new controller card was installed.

    C

    The SATA controller card was not set as a boot device in the computer BIOS.

    D

    The new controller must have the correct jumper settings for Windows mode.


    正确答案： B
    解析： 暂无解析

  • 第12题：

    单选题
    An administrator is configuring RAID 1 in a server.  The administrator has been given two matching 80GB SATA-2 hard drives， two SATA-2 cables， and a SATA-2 RAID adapter.  How should the administrator BEST configure these drives？（）
    A

    Install one drive on the first channel and install the second drive on the second channel.

    B

    Install one drive on the first cable， on the first channel. Install the second drive on the secondcable， on the second channel.

    C

    Install both drives on the same channel. Cable both drives as the primary master on the samecable.

    D

    Install both drives on the same channel. On the same cable one drive should be set as primaryslave and the other drive as the primary master.


    正确答案： A
    解析： 暂无解析

  • 第13题：

    A client purchased a new internal hard drive to act as a second drive on a legacy machine. When the client attempts to install the drive, the cable connector on the new drive is not compatible with the available IDE cables. It is determined that the client has purchased a SATA hard drive. Which of the following would the technician recommend as the BEST solution to this situation?（）

    • A、Have the client purchase a SATA compatible system board.
    • B、Have the client purchase a SATA to IDE conversion kit.
    • C、Have the client return the drive and purchase an IDE compatible drive.
    • D、Have the client purchase a SCSI to SATA conversion kit.

    正确答案:C

  • 第14题：

    A user requires more storage space on their computer. After a technician installs a second IDE drive in the computer, the system will not recognize that there are any hard drives installed. Which of the following is the MOST likely cause of the problem?（）

    • A、The second hard drive has not been formatted for NTFS.
    • B、The jumpers on both drives are set to the cable select position.
    • C、The jumper on the first drive is set to master and the second is set to slave.
    • D、The jumpers on both drives are set to the master position.

    正确答案:D

  • 第15题：

    An administrator is configuring RAID 1 in a server.  The administrator has been given two matching 80GB SATA-2 hard drives， two SATA-2 cables， and a SATA-2 RAID adapter.  How should the administrator BEST configure these drives？（）

    • A、Install one drive on the first channel and install the second drive on the second channel.
    • B、Install one drive on the first cable， on the first channel. Install the second drive on the secondcable， on the second channel.
    • C、Install both drives on the same channel. Cable both drives as the primary master on the samecable.
    • D、Install both drives on the same channel. On the same cable one drive should be set as primaryslave and the other drive as the primary master.

    正确答案:B

  • 第16题：

    The technician is working on a system and has determined that the hard drive must be reimaged. However, the customer wants to retain all the data. Which of the following would take the LEAST amount of time to implement?（）

    • A、Create a new partition on the hard drive, copy all data to the new partition, reimage the drive, and the old data will be on the new partition and accessible.
    • B、Install a new hard drive, slave the old drive, image the new drive, and show the customer how to access their data on the old drive.
    • C、Upload the data to an external FTP server, reimage the drive, and then restore the data to the newly imaged drive.
    • D、Copy data to a USB connected hard drive, reimage the drive, and then restore the data to the newly imaged drive.

    正确答案:D

  • 第17题：

    A technician installs a SATA controller card and moves the hard drive cable from the system board to the SATA controller. The system POSTs and the controller BIOS recognizes the hard drive but does not boot to the hard drive and start Windows. Which of the following is the MOST likely cause of the problem？（）

    • A、Windows cannot be booted from a controller card.
    • B、The hard drive must have Windows reinstalled because a new controller card was installed.
    • C、The SATA controller card was not set as a boot device in the computer BIOS.
    • D、The new controller must have the correct jumper settings for Windows mode.

    正确答案:C

  • 第18题：

    单选题
    The customer brings their mini-tower and a new DVD/RW drive they want installed. The technician finds a second hard drive in an empty 5.25 bay connected to the secondary bus and jumpered as a slave. The ribbon cable will not stretch from the primary hard drive to the open 5.25 inch bay. Which of the following is the BEST solution?（）
    A

    Connect the new DVD drive as the primary on the secondary bus and leave the old CD drive disconnected.

    B

    Move the secondary hard drive next to the primary hard drive and connect to the primary bus. Connect the new DVD drive as the slave on the secondary bus.

    C

    Move the secondary hard drive from the secondary to the primary bus and then reformat the hard drive after rebooting then reassign the drive letters in disk management prior to installing the new DVD drive on the secondary bus.

    D

    Move the secondary hard drive to the bay and then connect it to the primary bus. Connect themini-tower and the new DVD drive as the master on the secondary bus.


    正确答案： A
    解析： 暂无解析

  • 第19题：

    单选题
    A user requires more storage space on their computer. After a technician installs a second IDE drive in the computer, the system will not recognize that there are any hard drives installed. Which of the following is the MOST likely cause of the problem?（）
    A

    The second hard drive has not been formatted for NTFS.

    B

    The jumpers on both drives are set to the cable select position.

    C

    The jumper on the first drive is set to master and the second is set to slave.

    D

    The jumpers on both drives are set to the master position.


    正确答案： B
    解析： 暂无解析

  • 第20题：

    单选题
    Which of the following will allow a technician to extend a partition?（）
    A

    Set the drive up as basic

    B

    Format the drive to FAT32

    C

    Install a second hard drive

    D

    Set the drive as dynamic


    正确答案： A
    解析： 暂无解析

  • 第21题：

    单选题
    A user has recently added a second IDE CD-RW drive to a machine in addition to the primary DVD-ROM drive. The drive opens and closes; however, they do not see it show up in Windows. Which of the following is the MOST likely cause?（）
    A

    The drive jumper settings are incorrect.

    B

    The drive is not receiving power from PSU.

    C

    Windows only supports one optical drive.

    D

    The user connected the drive with a SATA cable.


    正确答案： C
    解析： 暂无解析

  • 第22题：

    单选题
    A defective CD-ROM drive is replaced with a new CD-ROM drive. The new CD-ROM drive is able to read any CD that it accesses， but music CDs do not play music. What is the MOST likely cause of this problem？（）
    A

    The audio cable is not connected to the drive.

    B

    The ribbon cable is not connected.

    C

    The power cable is not connected.

    D

    The CD-ROM drivers are not installed.


    正确答案： A
    解析： 暂无解析

  • 第23题：

    单选题
    A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller. Which of the following is the MOST likely cause of the problem?（）
    A

    Both hard drives have the master jumper in place.

    B

    One hard drive is set as master and the other slave.

    C

    The hard drive data cable is reversed.

    D

    Both hard drives have the cable select jumper in place.


    正确答案： C
    解析： 暂无解析

  • 第24题：

    单选题
    The technician is working on a system and has determined that the hard drive must be reimaged. However, the customer wants to retain all the data. Which of the following would take the LEAST amount of time to implement?（）
    A

    Create a new partition on the hard drive, copy all data to the new partition, reimage the drive, and the old data will be on the new partition and accessible.

    B

    Install a new hard drive, slave the old drive, image the new drive, and show the customer how to access their data on the old drive.

    C

    Upload the data to an external FTP server, reimage the drive, and then restore the data to the newly imaged drive.

    D

    Copy data to a USB connected hard drive, reimage the drive, and then restore the data to the newly imaged drive.


    正确答案： D
    解析： 暂无解析

相关内容