单选题Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）A The new drive’s jumper is s

题目
单选题
Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）
A

The new drive’s jumper is set for master.

B

The new drive is connected to the secondary bus as a slave drive.

C

Both drives’ jumpers are set for cable select.

D

The old drive’s jumper is set for master and the new drive is set for slave.

相似考题

1.A technician has lost a necessary jumper for a new hard drive that must be installed immediately.Which of the following is the BEST solution?()A. Use a jumper from the motherboard where the new drive is going to be installed.B. Use a jumper from a hard drive that is no longer functioning.C. Contact the manufacturer of the new hard drive and have a replacement jumper shipped immediately.D. The new hard drive must be replaced

2. The customer brings their mini-tower and a new DVD/RW drive they want installed. The technician finds a second hard drive in an empty 5.25 bay connected to the secondary bus and jumpered as a slave. The ribbon cable will not stretch from the primary hard drive to the open 5.25 inch bay. Which of the following is the BEST solution?（）A、Connect the new DVD drive as the primary on the secondary bus and leave the old CD drive disconnected.B、Move the secondary hard drive next to the primary hard drive and connect to the primary bus. Connect the new DVD drive as the slave on the secondary bus.C、Move the secondary hard drive from the secondary to the primary bus and then reformat the hard drive after rebooting then reassign the drive letters in disk management prior to installing the new DVD drive on the secondary bus.D、Move the secondary hard drive to the bay and then connect it to the primary bus. Connect themini-tower and the new DVD drive as the master on the secondary bus.

3.After performing the initial steps in installing the server OS from a DVD-ROM， the server reboots and goes back into the setup wizard. Which of the following is the MOST likely cause for this problem？（）A、The DVD-ROM drive has failed.B、An installation file copied from the DVD to the hard drive is corrupt.C、Faulty OS installation DVDD、Incorrect boot sequence in the BIOS

4.After installing a new hard drive into a server for the purpose of mirroring the data from the first drive to the second one， the server displays an “operating system not found” error. Which of the following should the technician do to boot the server from the original drive？（）A、Replace the second drive with a hot swappable one.B、Swap the drive boot order in the BIOSC、Make the second disk active under the disk management tool.D、Rebuild the array using the hardware RAID tool at boot.

参考答案和解析
正确答案： D
解析： 暂无解析
更多“单选题Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）A The new drive’s jumper is s”相关问题

  • 第1题：

    A technician has lost a necessary jumper for a new hard drive that must be installed immediately.Which of the following is the BEST solution?（）

    • A、Use a jumper from the motherboard where the new drive is going to be installed.
    • B、Use a jumper from a hard drive that is no longer functioning.
    • C、Contact the manufacturer of the new hard drive and have a replacement jumper shipped immediately.
    • D、The new hard drive must be replaced

    正确答案:B

  • 第2题：

    A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller. Which of the following is the MOST likely cause of the problem?（）

    • A、Both hard drives have the master jumper in place.
    • B、One hard drive is set as master and the other slave.
    • C、The hard drive data cable is reversed.
    • D、Both hard drives have the cable select jumper in place.

    正确答案:A

  • 第3题：

    A user requires more storage space on their computer. After a technician installs a second IDE drive in the computer, the system will not recognize that there are any hard drives installed. Which of the following is the MOST likely cause of the problem?（）

    • A、The second hard drive has not been formatted for NTFS.
    • B、The jumpers on both drives are set to the cable select position.
    • C、The jumper on the first drive is set to master and the second is set to slave.
    • D、The jumpers on both drives are set to the master position.

    正确答案:D

  • 第4题：

    Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）

    • A、The new drive’s jumper is set for master.
    • B、The new drive is connected to the secondary bus as a slave drive.
    • C、Both drives’ jumpers are set for cable select.
    • D、The old drive’s jumper is set for master and the new drive is set for slave.

    正确答案:A

  • 第5题：

    An administrator adds a new SATA hard drive into a functional server and attempts to boot the server. The server will no longer boot into the operating system. The administrator checks all the connections and reboots the server. The server still will not load the operating system.  Which of the following is the MOST probable cause？（）

    • A、The BIOS is set with the wrong boot order.
    • B、The jumpers have not been set on the hard drive.
    • C、The hard drive is not compatible with the system board.
    • D、The boot.ini file needs to be modified.

    正确答案:A

  • 第6题：

    A technician is booting up a computer but the computer never moves beyond POST. The floppydisk drive light stays lit continuously during the boot process. Which of the following is the MOST likely cause?（）

    • A、The hard drive is not formatted.
    • B、The BIOS is corrupted.
    • C、The motherboard has faulty capacitors.
    • D、The drive cable is backwards

    正确答案:D

  • 第7题：

    单选题
    A computer has been upgraded with a new hard drive and after reassembling the computer and turning the computer on， the drive LED remains lit and an error message during power-on self test （POST） states， ’No Drive Present.’ Which of the following would MOST likely be the cause？（）
    A

    The motherboard was damaged and needs replacing.

    B

    The floppy drive was not reconnected.

    C

    A configuration disk was left in the floppy drive.

    D

    The ribbon cable has been installed incorrectly.


    正确答案： D
    解析： 暂无解析

  • 第8题：

    单选题
    The customer brings their mini-tower and a new DVD/RW drive they want installed. The technician finds a second hard drive in an empty 5.25 bay connected to the secondary bus and jumpered as a slave. The ribbon cable will not stretch from the primary hard drive to the open 5.25 inch bay. Which of the following is the BEST solution?（）
    A

    Connect the new DVD drive as the primary on the secondary bus and leave the old CD drive disconnected.

    B

    Move the secondary hard drive next to the primary hard drive and connect to the primary bus. Connect the new DVD drive as the slave on the secondary bus.

    C

    Move the secondary hard drive from the secondary to the primary bus and then reformat the hard drive after rebooting then reassign the drive letters in disk management prior to installing the new DVD drive on the secondary bus.

    D

    Move the secondary hard drive to the bay and then connect it to the primary bus. Connect themini-tower and the new DVD drive as the master on the secondary bus.


    正确答案： A
    解析： 暂无解析

  • 第9题：

    单选题
    A user requires more storage space on their computer. After a technician installs a second IDE drive in the computer, the system will not recognize that there are any hard drives installed. Which of the following is the MOST likely cause of the problem?（）
    A

    The second hard drive has not been formatted for NTFS.

    B

    The jumpers on both drives are set to the cable select position.

    C

    The jumper on the first drive is set to master and the second is set to slave.

    D

    The jumpers on both drives are set to the master position.


    正确答案： B
    解析： 暂无解析

  • 第10题：

    单选题
    A technician has lost a necessary jumper for a new hard drive that must be installed immediately.Which of the following is the BEST solution?（）
    A

    Use a jumper from the motherboard where the new drive is going to be installed.

    B

    Use a jumper from a hard drive that is no longer functioning.

    C

    Contact the manufacturer of the new hard drive and have a replacement jumper shipped immediately.

    D

    The new hard drive must be replaced


    正确答案： A
    解析： 暂无解析

  • 第11题：

    单选题
    A technician purchases a new 120 GB IDE hard disk to use in an old server as a swap drive. After adding the drive to the server， the technician discovers that the operating system does not detect the drive.   After rebooting the server， the technician notices the drive is missing from POST and comes to the conclusion that the BIOS needs to be updated. The technician downloads the latest version of the BIOS update from the manufacturer website.   Which action should the technician take next？（）
    A

     backup the BIOS configuration to use later

    B

     install the BIOS update from a command prompt

    C

     create a bootable floppy and copy the BIOS update tools to the floppy

    D

     read the manufacturer’s guidelines and recommendations on installing the update


    正确答案： D
    解析： 暂无解析

  • 第12题：

    单选题
    A user reports that their hard drive has failed and needs to be replaced. Which of the following should the technician do FIRST?（）
    A

    Run the hard disk manufacturer’s diagnostic program

    B

    Re-image the drive

    C

    Replace the hard drive and load Windows

    D

    Ask the user diagnostic questions


    正确答案： D
    解析： 暂无解析

  • 第13题：

    A user reports that after configuring the BIOS to boot to the hard drive first, the system still tries to boot from the optical drive. Which of the following is the MOST likely cause?（）

    • A、Optical drive
    • B、Power supply
    • C、CMOS battery
    • D、CD-ROM disk

    正确答案:C

  • 第14题：

    A technician purchases a new 120 GB IDE hard disk to use in an old server as a swap drive. After adding the drive to the server， the technician discovers that the operating system does not detect the drive.   After rebooting the server， the technician notices the drive is missing from POST and comes to the conclusion that the BIOS needs to be updated. The technician downloads the latest version of the BIOS update from the manufacturer website.   Which action should the technician take next？（）

    • A、 backup the BIOS configuration to use later
    • B、 install the BIOS update from a command prompt
    • C、 create a bootable floppy and copy the BIOS update tools to the floppy
    • D、 read the manufacturer’s guidelines and recommendations on installing the update

    正确答案:D

  • 第15题：

    A computer has been upgraded with a new hard drive and after reassembling the computer and turning the computer on， the drive LED remains lit and an error message during power-on self test （POST） states， ’No Drive Present.’ Which of the following would MOST likely be the cause？（）

    • A、The motherboard was damaged and needs replacing.
    • B、The floppy drive was not reconnected.
    • C、A configuration disk was left in the floppy drive.
    • D、The ribbon cable has been installed incorrectly.

    正确答案:D

  • 第16题：

    When attempting to boot a PC, the POST process completes without error. The PC then displays,‘non system disk or disk error’. Which of the following would MOST likely cause the issue?（）

    • A、Out-of-date BIOS
    • B、Invalid motherboard jumper settings
    • C、Failing power supply
    • D、Floppy disk in the drive

    正确答案:D

  • 第17题：

    A technician installs a SATA controller card and moves the hard drive cable from the system board to the SATA controller. The system POSTs and the controller BIOS recognizes the hard drive but does not boot to the hard drive and start Windows. Which of the following is the MOST likely cause of the problem？（）

    • A、Windows cannot be booted from a controller card.
    • B、The hard drive must have Windows reinstalled because a new controller card was installed.
    • C、The SATA controller card was not set as a boot device in the computer BIOS.
    • D、The new controller must have the correct jumper settings for Windows mode.

    正确答案:C

  • 第18题：

    单选题
    After performing the initial steps in installing the server OS from a DVD-ROM， the server reboots and goes back into the setup wizard. Which of the following is the MOST likely cause for this problem？（）
    A

    The DVD-ROM drive has failed.

    B

    An installation file copied from the DVD to the hard drive is corrupt.

    C

    Faulty OS installation DVD

    D

    Incorrect boot sequence in the BIOS


    正确答案： D
    解析： 暂无解析

  • 第19题：

    单选题
    A user reports that after configuring the BIOS to boot to the hard drive first, the system still tries to boot from the optical drive. Which of the following is the MOST likely cause?（）
    A

    Optical drive

    B

    Power supply

    C

    CMOS battery

    D

    CD-ROM disk


    正确答案： C
    解析： 暂无解析

  • 第20题：

    单选题
    Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）
    A

    The new drive’s jumper is set for master.

    B

    The new drive is connected to the secondary bus as a slave drive.

    C

    Both drives’ jumpers are set for cable select.

    D

    The old drive’s jumper is set for master and the new drive is set for slave.


    正确答案： A
    解析： 暂无解析

  • 第21题：

    单选题
    When attempting to boot a PC, the POST process completes without error. The PC then displays,‘non system disk or disk error’. Which of the following would MOST likely cause the issue?（）
    A

    Out-of-date BIOS

    B

    Invalid motherboard jumper settings

    C

    Failing power supply

    D

    Floppy disk in the drive


    正确答案： D
    解析： 暂无解析

  • 第22题：

    单选题
    After installing a new hard drive into a server for the purpose of mirroring the data from the first drive to the second one， the server displays an “operating system not found” error. Which of the following should the technician do to boot the server from the original drive？（）
    A

    Replace the second drive with a hot swappable one.

    B

    Swap the drive boot order in the BIOS

    C

    Make the second disk active under the disk management tool.

    D

    Rebuild the array using the hardware RAID tool at boot.


    正确答案： C
    解析： 暂无解析

  • 第23题：

    单选题
    A technician installs a SATA controller card and moves the hard drive cable from the system board to the SATA controller. The system POSTs and the controller BIOS recognizes the hard drive but does not boot to the hard drive and start Windows. Which of the following is the MOST likely cause of the problem？（）
    A

    Windows cannot be booted from a controller card.

    B

    The hard drive must have Windows reinstalled because a new controller card was installed.

    C

    The SATA controller card was not set as a boot device in the computer BIOS.

    D

    The new controller must have the correct jumper settings for Windows mode.


    正确答案： B
    解析： 暂无解析

  • 第24题：

    单选题
    A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller. Which of the following is the MOST likely cause of the problem?（）
    A

    Both hard drives have the master jumper in place.

    B

    One hard drive is set as master and the other slave.

    C

    The hard drive data cable is reversed.

    D

    Both hard drives have the cable select jumper in place.


    正确答案： C
    解析： 暂无解析

相关内容