单选题In JUNOS software， which command is used to configure TED support for OSPF？（）A set protocols rsvp cspf-enableB set protocols mpls cspf-enableC set protocols rsvp traffic-engineeringD set protocols ospf traffic-engineering

第1题：

第2题：

You wish to configure IPv6 support on a router which does not have any current IPv4 configuration.Which three steps are used to configure IPv6 with an accompanying IGP in JUNOS software? （）

• A、set protocols isis inet6
• B、set routing-options router-id router-id
• C、set protocols ospf3 area 0 interface all
• D、set interface fe-0/0/1 unit 0 family inet6
• E、set routing-options ipv6-router-id router-id

正确答案:B,C

第3题：

Which two commands would change the default OSPF metric calculation for interface ge-0/3/0 in JUNOS software？（）

• A、set interfaces ge-0/3/0 unit 0 metric 10
• B、set protocols ospf reference-bandwidth 10g
• C、set interfaces ge-0/3/0 unit bandwidth 10g
• D、set protocols ospf area 0 interface ge-0/3/0 metric 10
• E、set protocols ospf area 0 interface ge-0/3/0 bandwidth 10g

正确答案:B,D

第4题：

Which statement would prevent the sending of redundant route advertisements when your routereflector cluster is fully meshed?（）

• A、set protocols bgp group mygroup path-selection cisco-non-deterministic;
• B、set protocols bgp group i-bgp no-aggregator-id;
• C、set protocols bgp group mygroup no-client-reflect;
• D、set protocols bgp group i-bgp damping;

正确答案:C

第5题：

You are at the top of the hierarchy and must configure OSPF on interface so-0/0/0 unit 100. Which two achieve this result?（）

• A、set protocols   setospf area 0   set interface so-0/0/0.100
• B、set protocols ospf area 0 interface so-0/0/0.100
• C、edit protocols ospf interface so-0/0/0.100
• D、edit protocols ospf area 0   set interface so-0/0/0.100

正确答案:B,D

第6题：

In JUNOS software， which command is used to configure TED support for OSPF？（）

• A、set protocols rsvp cspf-enable
• B、set protocols mpls cspf-enable
• C、set protocols rsvp traffic-engineering
• D、set protocols ospf traffic-engineering

正确答案:D

第7题：

Which two commands are needed to create and apply an export policy that advertises static routes to OSPF neighbors?（）

• A、edit policy-options policy-statement policy-name set term 1 from protocol static set term 1 then accept
• B、edit ospf policy set from protocol static set 1 then accept
• C、set protocols OSPF export policy-name
• D、set protocols OSPF policy policy-name

正确答案:A,C

第8题：

You are at the top of the hierarchy and must configure OSPF on interface so-0/0/0 unit 100. Which two achieve this result?（）

• A、set protocols    set ospf area 0    set interface so-0/0/0.100
• B、set protocols ospf area 0 interface so-0/0/0.100
• C、edit protocols ospf interface so-0/0/0.100
• D、edit protocols ospf area 0 set interface so-0/0/0.100

正确答案:B,D

第9题：

Which two commands would change the default OSPF metric calculation for interface ge-0/3/0 inJUNOS software?（）

• A、set interfaces ge-0/3/0 unit 0 metric 10
• B、set protocols ospf reference-bandwidth 10g
• C、set interfaces ge-0/3/0 unit 0 bandwidth 10g
• D、set protocols ospf area 0 interface ge-0/3/0 metric 10
• E、set protocols ospf area 0 interface ge-0/3/0 bandwidth 10g

正确答案:B,D

第10题：

第11题：

第12题：

第13题：

第14题：

In MPLS traffic engineering， which one of the following protocols is used for Path Setup？（）

• A、BGP
• B、OSPF
• C、ISIS
• D、RSVP

正确答案:D

第15题：

Which command will apply a policy to redistribute static routes into OSPF?（）

• A、set protocols ospf import static-routes
• B、set protocols ospf export static-routes
• C、set routing-options static defaults readvertise
• D、set routing-options static route 0.0.0.0/0 readvertise

正确答案:B

第16题：

Which configuration causes RIP-learned routes to be advertised to other RIP neighbors?（）

• A、set protocol rip no-passive
• B、top edit policy-options policy-statement demo   set term 1 from protocol rip   set term 1 then accept   top set protocols rip group internal export demo
• C、set protocols rip advertise m-out
• D、top edit policy-options policy-statement demo   set term 1 from active routes   set term 1 then accept   top set protocols rip group internal export demo

正确答案:B

第17题：

Which CLI command is used to see the current OSPF link-state database?（）

• A、show ospf database
• B、show ospf neighbor
• C、show protocols ospf
• D、show ospf link-state

正确答案:A

第18题：

Which two can be used to create and apply an export policy that advertises static routes to RIP neighbors?（）

• A、set protocols rip export demo
• B、edit policy-options policy-statement demo   set term 1 from protocol static   set term 1 then accept
• C、edit policy-options policy-statement demo   set term 1 from protocol static accept
• D、set protocols rip group internal export demo

正确答案:B,D

第19题：

You want to limit the number of Type 7 LSAs to be converted into Type 5 LSAs at an appropriate ARB. Which two commands should you use from the [edit] hierarchy level within the JUNOS software configuration mode？（）

• A、set protocols ospf area-range network/mask-length
• B、set protocols ospf area area-id nssa area-range network/mask-length
• C、set protocols ospf area area-id area-range network/mask-length restrict
• D、set protocols ospf area area-id nssa area-range network/mask-length restrict

正确答案:B,D

第20题：

You want to limit the number of Type 7 LSAs to be converted into Type 5 LSAs at an appropriateABR. Which two commands should you use from the [edit] hierarchy level within JUNOS configuration mode?（）

• A、set protocols ospf area-range network/mask-length
• B、set protocols ospf area area-id nssa area-range network/mask-length
• C、set protocols ospf area area-id area-range network/mask-length restrict
• D、set protocols ospf area area-id nssa area-range network/mask-length restrict

正确答案:B,D

第21题：

第22题：

第23题：