多选题You are at the top of the hierarchy and must configure OSPF on interface so-0/0/0 unit 100. Which two achieve this result?（）Aset protocols set ospf area 0 set interface so-0/0/0.100Bset protocols ospf area 0 interface so-0/0/0.100Cedit protocols

题目
多选题
You are at the top of the hierarchy and must configure OSPF on interface so-0/0/0 unit 100. Which two achieve this result?（）
A

set protocols    set ospf area 0    set interface so-0/0/0.100

B

set protocols ospf area 0 interface so-0/0/0.100

C

edit protocols ospf interface so-0/0/0.100

D

edit protocols ospf area 0 set interface so-0/0/0.100

相似考题

1.You want to allow your device to establish OSPF adjacencies with a neighboring device connected to interface ge-0/0/3.0. Interface ge-0/0/3.0 is a member of the HR zone.Under which configuration hierarchy must you permit OSPF traffic?（）A. [edit security policies from-zone HR to-zone HR]B. [edit security zones functional-zone management protocols]C. [edit security zones protocol-zone HR host-inbound-traffic]D. [edit security zones security-zone HR host-inbound-traffic protocols]

2.Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）A. All OSPF implementations must have at le ast one interface in area 0.B. You are attempting to run in the broadcast mode over an NBMA interface.C. Both routers are configured to function as a BDR; therefore, there is no DR router.D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.

3.Which of the following are characteristics of OSPF areas?()A. Hierarchical OSPF networks need to be in one areaB. Multiple OSPF areas must connect to area 0C. Single area OSPF networks must be configured in area 1D. Areas can be assigned any number from 0 to 63535E. Area 0 is called the backbone areaF. Each OSPF area need to be configured with a loopback interface

4.You wish to configure IPv6 support on a router which does not have any current IPv4 configuration.Which three steps are used to configure IPv6 with an accompanying IGP in JUNOS software? ()A. set protocols isis inet6B. set routing-options router-id router-idC. set protocols ospf3 area 0 interface allD. set interface fe-0/0/1 unit 0 family inet6E. set routing-options ipv6-router-id router-id

更多“多选题You are at the top of the hierarchy and must configure OSPF on interface so-0/0/0 unit 100. Which two achieve this result?（）Aset protocols set ospf area 0 set interface so-0/0/0.100Bset protocols ospf area 0 interface so-0/0/0.100Cedit protocols ospf i”相关问题

  • 第1题：

    Which of the following are true statements regarding the characteristics of OSPF areas? Select all that apply.()

    A. All OSPF networks require the use of multiple areas

    B. Multiple OSPF areas must connect to area 0

    C. Single area OSPF networks must be configured in area 1

    D. Areas can be assigned any number from 0 to 63535

    E. Area 0 is called the backbone area

    F. Each OSPF area need to be configured with a loopback interface


    参考答案：B, E

  • 第2题：

    You wish to configure IPv6 support on a router which does not have any current IPv4 configuration.Which three steps are used to configure IPv6 with an accompanying IGP in JUNOS software? （）

    • A、set protocols isis inet6
    • B、set routing-options router-id router-id
    • C、set protocols ospf3 area 0 interface all
    • D、set interface fe-0/0/1 unit 0 family inet6
    • E、set routing-options ipv6-router-id router-id

    正确答案:B,C

  • 第3题：

    You are the top of hierarchy and must configure OSPF on inteface so-0/0/0 unit 100. Which two achieve this result?（）

    • A、set protocols   set ospf area 0   set interface so-0/0/0.100
    • B、set protocols ospf area 0 interface so-0/0/0.100
    • C、edit protocols ospf interface so-0/0/0.100
    • D、edit protocols ospf area 0   set interface so-0/0/0.100

    正确答案:B,D

  • 第4题：

    You want to allow your device to establish OSPF adjacencies with a neighboring device connected to interface ge-0/0/3.0. Interface ge-0/0/3.0 is a member of the HR zone.Under which configuration hierarchy must you permit OSPF traffic?（）

    • A、[edit security policies from-zone HR to-zone HR]
    • B、[edit security zones functional-zone management protocols]
    • C、[edit security zones protocol-zone HR host-inbound-traffic]
    • D、[edit security zones security-zone HR host-inbound-traffic protocols]

    正确答案:D

  • 第5题：

    You accidentally configured interface so-0/0/0.0 with /32 instead of /30. Which two solutions could you use to correct this configuration?（）

    • A、[edit interfaces so-0/0/0.0]   user@router# replace family inetaddress /32 with /30
    • B、[edit interfaces so-0/0/0.0]   user@router# rename family inetaddress /32 to address /30
    • C、[edit]   user@router# replace interface so-0/0/0.0 family inetaddress /32 with address /30
    • D、[edit interfaces so-0/0/0.0]   user@router# delete family inet address   user@router# set family inetaddress /30

    正确答案:B,D

  • 第6题：

    You want to limit the number of Type 7 LSAs to be converted into Type 5 LSAs at an appropriate ARB. Which two commands should you use from the [edit] hierarchy level within the JUNOS software configuration mode？（）

    • A、set protocols ospf area-range network/mask-length
    • B、set protocols ospf area area-id nssa area-range network/mask-length
    • C、set protocols ospf area area-id area-range network/mask-length restrict
    • D、set protocols ospf area area-id nssa area-range network/mask-length restrict

    正确答案:B,D

  • 第7题：

    You want to limit the number of Type 7 LSAs to be converted into Type 5 LSAs at an appropriateABR. Which two commands should you use from the [edit] hierarchy level within JUNOS configuration mode?（）

    • A、set protocols ospf area-range network/mask-length
    • B、set protocols ospf area area-id nssa area-range network/mask-length
    • C、set protocols ospf area area-id area-range network/mask-length restrict
    • D、set protocols ospf area area-id nssa area-range network/mask-length restrict

    正确答案:B,D

  • 第8题：

    多选题
    You accidentally configured interface so-0/0/0.0 with /32 instead of /30. Which two solutions could you use to correct this configuration?（）
    A

    [edit interfaces so-0/0/0.0]   user@router# replace family inetaddress /32 with /30

    B

    [edit interfaces so-0/0/0.0]   user@router# rename family inetaddress /32 to address /30

    C

    [edit]   user@router# replace interface so-0/0/0.0 family inetaddress /32 with address /30

    D

    [edit interfaces so-0/0/0.0]   user@router# delete family inet address   user@router# set family inetaddress /30


    正确答案： D,C
    解析： 暂无解析

  • 第9题：

    多选题
    Which of the following are true statements regarding the characteristics of OSPF areas? Select all that apply.（）
    A

    All OSPF networks require the use of multiple areas

    B

    Multiple OSPF areas must connect to area 0

    C

    Single area OSPF networks must be configured in area 1

    D

    Areas can be assigned any number from 0 to 63535

    E

    Area 0 is called the backbone area

    F

    Each OSPF area need to be configured with a loopback interface


    正确答案： D,B
    解析： 暂无解析

  • 第10题：

    多选题
    You are at the top of the hierarchy and must configure OSPF on interface so-0/0/0 unit 100. Which two achieve this result?（）
    A

    set protocols    set ospf area 0    set interface so-0/0/0.100

    B

    set protocols ospf area 0 interface so-0/0/0.100

    C

    edit protocols ospf interface so-0/0/0.100

    D

    edit protocols ospf area 0 set interface so-0/0/0.100


    正确答案： D,B
    解析： 暂无解析

  • 第11题：

    多选题
    Which two commands would change the default OSPF metric calculation for interface ge-0/3/0 inJUNOS software?（）
    A

    set interfaces ge-0/3/0 unit 0 metric 10

    B

    set protocols ospf reference-bandwidth 10g

    C

    set interfaces ge-0/3/0 unit 0 bandwidth 10g

    D

    set protocols ospf area 0 interface ge-0/3/0 metric 10

    E

    set protocols ospf area 0 interface ge-0/3/0 bandwidth 10g


    正确答案： C,D
    解析： 暂无解析

  • 第12题：

    多选题
    You are at the top of the hierarchy and must configure OSPF on interface so-0/0/0 unit 100.Which two achieve this result?（）
    A

    set protocols   setospf area 0   set interface so-0/0/0.100

    B

    set protocols ospf area 0 interface so-0/0/0.100

    C

    edit protocols ospf interface so-0/0/0.100

    D

    edit protocols ospf area 0   set interface so-0/0/0.100


    正确答案： D,A
    解析： 暂无解析

  • 第13题：

    在 VRP 操作系统中，能进入 OSPF 区域 0 的视图的是（ ）

    A.[Huawei]ospf area 0
    B.[Huawei‐ospf‐1]interface area 0
    C.[Huawei‐ospf‐1]area 0.0.0.0
    D.[Huawei‐ospf‐1]area 0 enale

    答案：C
    解析：
    进入区域0试图，必须先进入ospf试图，然后使用area命令。

  • 第14题：

    Which two commands would change the default OSPF metric calculation for interface ge-0/3/0 in JUNOS software？（）

    • A、set interfaces ge-0/3/0 unit 0 metric 10
    • B、set protocols ospf reference-bandwidth 10g
    • C、set interfaces ge-0/3/0 unit bandwidth 10g
    • D、set protocols ospf area 0 interface ge-0/3/0 metric 10
    • E、set protocols ospf area 0 interface ge-0/3/0 bandwidth 10g

    正确答案:B,D

  • 第15题：

    You are at the top of the hierarchy and must configure OSPF on interface so-0/0/0 unit 100.Which two achieve this result?（）

    • A、set protocols   setospf area 0   set interface so-0/0/0.100
    • B、set protocols ospf area 0 interface so-0/0/0.100
    • C、edit protocols ospf interface so-0/0/0.100
    • D、edit protocols ospf area 0   set interface so-0/0/0.100

    正确答案:B,D

  • 第16题：

    Which of the following are characteristics of OSPF areas?（）

    • A、Hierarchical OSPF networks need to be in one area
    • B、Multiple OSPF areas must connect to area 0
    • C、Single area OSPF networks must be configured in area 1
    • D、Areas can be assigned any number from 0 to 63535
    • E、Area 0 is called the backbone area
    • F、Each OSPF area need to be configured with a loopback interface

    正确答案:B,E

  • 第17题：

    You are at the top of the hierarchy and must configure OSPF on interface so-0/0/0 unit 100. Which two achieve this result?（）

    • A、set protocols   setospf area 0   set interface so-0/0/0.100
    • B、set protocols ospf area 0 interface so-0/0/0.100
    • C、edit protocols ospf interface so-0/0/0.100
    • D、edit protocols ospf area 0   set interface so-0/0/0.100

    正确答案:B,D

  • 第18题：

    You are at the top of the hierarchy and must configure OSPF on interface so-0/0/0 unit 100. Which two achieve this result?（）

    • A、set protocols    set ospf area 0    set interface so-0/0/0.100
    • B、set protocols ospf area 0 interface so-0/0/0.100
    • C、edit protocols ospf interface so-0/0/0.100
    • D、edit protocols ospf area 0 set interface so-0/0/0.100

    正确答案:B,D

  • 第19题：

    Which two commands would change the default OSPF metric calculation for interface ge-0/3/0 inJUNOS software?（）

    • A、set interfaces ge-0/3/0 unit 0 metric 10
    • B、set protocols ospf reference-bandwidth 10g
    • C、set interfaces ge-0/3/0 unit 0 bandwidth 10g
    • D、set protocols ospf area 0 interface ge-0/3/0 metric 10
    • E、set protocols ospf area 0 interface ge-0/3/0 bandwidth 10g

    正确答案:B,D

  • 第20题：

    多选题
    You are the top of hierarchy and must configure OSPF on inteface so-0/0/0 unit 100. Which two achieve this result?（）
    A

    set protocols   set ospf area 0   set interface so-0/0/0.100

    B

    set protocols ospf area 0 interface so-0/0/0.100

    C

    edit protocols ospf interface so-0/0/0.100

    D

    edit protocols ospf area 0   set interface so-0/0/0.100


    正确答案： A,C
    解析： 暂无解析

  • 第21题：

    多选题
    Which two commands would change the default OSPF metric calculation for interface ge-0/3/0 in JUNOS software？（）
    A

    set interfaces ge-0/3/0 unit 0 metric 10

    B

    set protocols ospf reference-bandwidth 10g

    C

    set interfaces ge-0/3/0 unit bandwidth 10g

    D

    set protocols ospf area 0 interface ge-0/3/0 metric 10

    E

    set protocols ospf area 0 interface ge-0/3/0 bandwidth 10g


    正确答案： A,D
    解析： 暂无解析

  • 第22题：

    多选题
    Which of the following are characteristics of OSPF areas?（）
    A

    Hierarchical OSPF networks need to be in one area

    B

    Multiple OSPF areas must connect to area 0

    C

    Single area OSPF networks must be configured in area 1

    D

    Areas can be assigned any number from 0 to 63535

    E

    Area 0 is called the backbone area

    F

    Each OSPF area need to be configured with a loopback interface


    正确答案： F,E
    解析： 暂无解析

  • 第23题：

    多选题
    You wish to configure IPv6 support on a router which does not have any current IPv4 configuration.Which three steps are used to configure IPv6 with an accompanying IGP in JUNOS software? （）
    A

    set protocols isis inet6

    B

    set routing-options router-id router-id

    C

    set protocols ospf3 area 0 interface all

    D

    set interface fe-0/0/1 unit 0 family inet6

    E

    set routing-options ipv6-router-id router-id


    正确答案： E,A
    解析： 暂无解析

  • 第24题：

    多选题
    You are at the top of the hierarchy and must configure OSPF on interface so-0/0/0 unit 100. Which two achieve this result?（）
    A

    set protocols   setospf area 0   set interface so-0/0/0.100

    B

    set protocols ospf area 0 interface so-0/0/0.100

    C

    edit protocols ospf interface so-0/0/0.100

    D

    edit protocols ospf area 0   set interface so-0/0/0.100


    正确答案： B,D
    解析： 暂无解析

相关内容