多选题Which of the following statements are true for routers but not true for Layer 3 Ethernet switches？（Choose all that apply.）（）AMay have Ethernet as well as non-Ethernet interfacesBTraditionally used as a standalone device for inter-VLAN communicationCMak

题目
多选题
Which of the following statements are true for routers but not true for Layer 3 Ethernet switches？（Choose all that apply.）（）
A

May have Ethernet as well as non-Ethernet interfaces

B

Traditionally used as a standalone device for inter-VLAN communication

C

Makes use of TCAMs

D

Uses subinterfaces to define trunks

E

Can use both Layer 2 and Layer 3 to make forwarding decisions

F

Allows the definition of Switched Virtual Interfaces（SVI）

相似考题

1.When comparing and contrasting the similarities and differences between bridges and switches, which of the following are valid statements? Choose all the valid answer choices)A. Bridges are faster than switches because they have fewer ports.B. A switch is a multiport bridge,C. Bridges and switches learn MAC addresses by examining the source MAC address of each frame. received.D. A bridge will forward a broadcast but a switch will not.E. Bridges and switches increase the size of a collision domain.F. None of the above statements are true.

2.With regard to Ethernet media access methods, which of the following are true?(Choose all that apply.)A．A device waits for an electronic signal before transmitting.B．A device listens and waits until the media is not busy before transmitting.C．All devices on an Ethernet segment see data that passes on the network medium.D．Only the sender and the receiver devices see data that passes on the network medium.E．Ethernet networks allow you to configured devises with higher transmission priority.

3.With regard to bridges and switches, which of the following statements are true?()A. Switches are primarily software based while bridges are hardware based.B. Both bridges and switches forward Layer 2 broadcasts.C. Bridges are frequently faster than switches.D. Switches typically have a higher number of ports than bridges.E. Bridges define broadcast domain while switches define collision domains.F. Both bridges and switches make forwarding decisions based on Layer 2 addresses.

4.Both bridges are switches are being used throughout the Ezonexam LAN. Which of the following statements are true regarding bridges and switches in this network?(Choose 3)A. Switches are primarily software based while bridges are hardware based.B. Switches usually have a higher number of ports than most bridges.C. Bridges are frequently faster than switches.D. Bridges define broadcast domains while switches define collision domains.E. Both bridges and switches forward Layer 2 broadcasts.F. Both bridges and switches make forwarding decisions based on Layer 2 addresses.

更多“多选题Which of the following statements are true for routers but not true for Layer 3 Ethernet switches？（Choose all that apply.）（）AMay have Ethernet as well as non-Ethernet interfacesBTraditionally used as a standalone device for inter-VLAN communicationCMak”相关问题

  • 第1题：

    Which of the following statements are true regarding bridges and switches (Choose 3.)()。

    A.Switches are primarily software based while bridges are hardware based.

    B.Both bridges and switches forward Layer 2 broadcasts.

    C.Bridges are frequently faster than switches.

    D.Switches have a higher number of ports than most bridges.

    E.Bridges define broadcast domains while switches define collision domains.

    F.Both bridges and switches make forwarding decisions based on Layer 2 addresses.


    参考答案：B, D, F

  • 第2题：

    Which three statements about NetFlow are true？ （）

    • A、LCP is used for PPP over ATM （PPPoA） setup.
    • B、LCP is used for PPP over Ethernet （PPPoE） setup.
    • C、LCP is used for PPP over Ethernet （PPPoPR） setup.
    • D、LCP is used for PPP CHAP authentication.
    • E、LCP is used for basic PPP link setup and operation.

    正确答案:A,B,E

  • 第3题：

    Which statement is true regarding an Ethernet collision domain?（）

    • A、If a router is used, the collision domain includes all devices connected to the router.
    • B、If a hub is used, the collision domain is limited to each device and the hub.
    • C、If a switch is used, the collision domain is limited to each device and the switch.
    • D、If a bridge is used, the collision domain includes all devices connected to the bridge.

    正确答案:C

  • 第4题：

    Which four statements about Ethernet virtual circuit （EVC） infrastructure are true？ （）

    • A、EVC infrastructure is a Layer 3 platform-independent routing architecture that supports IP overEthernet services
    • B、Ethernet flow point （EFP） is configured on the main interface
    • C、Feature commands like MQC-based QoS policies can be specified
    • D、EVC infrastructure is a Layer 2 platform-independent bridging architecture that supports Ethernetservices
    • E、Each Ethernet flow point （EFP） matches a predefined VLAN tag-based criteria
    • F、Ethernet flow point （EFP） is configured on the VLAN interface

    正确答案:B,D,E,F

  • 第5题：

    With regard to Ethernet media access methods, which of the following are true?（）

    • A、A device waits for an electronic signal before transmitting.
    • B、A device listens and waits until the media is not busy before transmitting.
    • C、All devices on an Ethernet segment see data that passes on the network medium.
    • D、Only the sender and the receiver devices see data that passes on the network medium.
    • E、Ethernet networks allow you to configured devises with higher transmission priority.

    正确答案:B,C

  • 第6题：

    Which two statements are true regarding an Ethernet collision domain?（）

    • A、The likelihood of collisions occurring increases when a switch is used.
    • B、The likelihood of collisions occurring increases when a hub is used.
    • C、If a hub is used, the collision domain is limited to each device and the hub.
    • D、If a switch is used, the collision domain is limited to each device and the switch.

    正确答案:B,D

  • 第7题：

    Which of the following is a true statement when promiscuous mode is enabled on an Integrated Virtual Ethernet？（）

    • A、 The physical port can be used as part of a Shared Ethernet Adapter （SEA）.
    • B、 All physical ports on the Host Ethernet Adapter （HEA） default to promiscuous mode.
    • C、 Multiple logical ports can be assigned to a physical port if that logical port is in promiscuous mode.
    • D、 All physical ports that belong to the same port group will be set to promiscuous mode on the Host Ethernet Adapter （HEA）.

    正确答案:A

  • 第8题：

    多选题
    Which of the following statements are true regarding bridges and switches? (Choose 3.)（）
    A

    Switches are primarily software based while bridges are hardware based.

    B

    Both bridges and switches forward Layer 2 broadcasts.

    C

    Bridges are frequently faster than switches.

    D

    Switches have a higher number of ports than most bridges.

    E

    Bridges define broadcast domains while switches define collision domains.

    F

    Both bridges and switches make forwarding decisions based on Layer 2 addresses.


    正确答案： B,D
    解析： 暂无解析

  • 第9题：

    多选题
    Which three statements about NetFlow are true？ （）
    A

    LCP is used for PPP over ATM （PPPoA） setup.

    B

    LCP is used for PPP over Ethernet （PPPoE） setup.

    C

    LCP is used for PPP over Ethernet （PPPoPR） setup.

    D

    LCP is used for PPP CHAP authentication.

    E

    LCP is used for basic PPP link setup and operation.


    正确答案： D,E
    解析： 暂无解析

  • 第10题：

    多选题
    Which two statements are true regarding an Ethernet collision domain?（）
    A

    The likelihood of collisions occurring increases when a switch is used.

    B

    The likelihood of collisions occurring increases when a hub is used.

    C

    If a hub is used, the collision domain is limited to each device and the hub.

    D

    If a switch is used, the collision domain is limited to each device and the switch.


    正确答案： B,A
    解析： 暂无解析

  • 第11题：

    单选题
    Which statement is true regarding an Ethernet collision domain?（）
    A

    If a router is used, the collision domain includes all devices connected to the router

    B

    If a hub is used, the colision domain is limited to each device and the hub

    C

    If a switch is used, the collision domain is limited to each device and the switch

    D

    If a bridge is used, the collision domain includes all devices connected to the bridge


    正确答案： B
    解析： 暂无解析

  • 第12题：

    多选题
    Which of the following statements are true regarding Layer 3 switches？（Choose all that apply.）（）
    A

    A routed port does not run STP or DTP

    B

    A routed port is considered to be in a down state if it is not operational at both Layer 1 andLayer 2

    C

    An SVI is considered to be in a down state if it is not operational at both Layer 1 and Layer 2

    D

    An SVI is considered to be in a down state only when none of the ports in the correspondingVLAN are active

    E

    An SVI port does not run 5TP or DTP

    F

    To create a trunk， an SVI can be logically divided into subinterfaces


    正确答案： A,B,D
    解析： 暂无解析

  • 第13题：

    Which of the following statements are true for routers but not true for Layer 3 Ethernet switches？（Choose all that apply.）（）

    • A、May have Ethernet as well as non-Ethernet interfaces
    • B、Traditionally used as a standalone device for inter-VLAN communication
    • C、Makes use of TCAMs
    • D、Uses subinterfaces to define trunks
    • E、Can use both Layer 2 and Layer 3 to make forwarding decisions
    • F、Allows the definition of Switched Virtual Interfaces（SVI）

    正确答案:A,B,D

  • 第14题：

    Which of the following characteristics are true assuming you are troubleshooting a networkcurrently enabled for VRRP？（Choose all that apply.）（）

    • A、The network is load balancing among different members of the VRRP group
    • B、The default hello timers are 1 second
    • C、The interface IP address is being used as the virtual IP address
    • D、There are several routers in the group simultaneously forwarding traffic for the group
    • E、It is a Cisco Proprietary protocol
    • F、The default hello timers are 3 seconds

    正确答案:B,C

  • 第15题：

    Which two statements are true regarding an Ethernet collision domain?（）

    • A、If a switch is used, the collision domain is limited to each device and the switch
    • B、If a hub is used, the collision domain is limited to each device and the hub
    • C、If a hub is used, the collision domain includes all devices connected to the hub
    • D、If a switch is used, the collision domain includes all devices connected to the switch

    正确答案:A,C

  • 第16题：

    Which of the following statements are true regarding Layer 3 switches？（Choose all that apply.）（）

    • A、A routed port does not run STP or DTP
    • B、A routed port is considered to be in a down state if it is not operational at both Layer 1 andLayer 2
    • C、An SVI is considered to be in a down state if it is not operational at both Layer 1 and Layer 2
    • D、An SVI is considered to be in a down state only when none of the ports in the correspondingVLAN are active
    • E、An SVI port does not run 5TP or DTP
    • F、To create a trunk， an SVI can be logically divided into subinterfaces

    正确答案:A,B,D

  • 第17题：

    Which two statements are true regarding an Ethernet collision domain?（）

    • A、If a switch is used, the collision domain is limited to each device and the switch.
    • B、If a hub is used, the collision domain is limited to each device and the hub.
    • C、If a hub is used, the collision domain includes all devices connected to the hub.
    • D、If a switch is used, the collision domain includes all devices connected to the switch.

    正确答案:A,C

  • 第18题：

    Which statement is true regarding an Ethernet collision domain?（）

    • A、If a router is used, the collision domain includes all devices connected to the router
    • B、If a hub is used, the colision domain is limited to each device and the hub
    • C、If a switch is used, the collision domain is limited to each device and the switch
    • D、If a bridge is used, the collision domain includes all devices connected to the bridge

    正确答案:C

  • 第19题：

    多选题
    Which two statements are true regarding an Ethernet collision domain?（）
    A

    If a switch is used, the collision domain is limited to each device and the switch.

    B

    If a hub is used, the collision domain is limited to each device and the hub.

    C

    If a hub is used, the collision domain includes all devices connected to the hub.

    D

    If a switch is used, the collision domain includes all devices connected to the switch.


    正确答案： A,C
    解析： 暂无解析

  • 第20题：

    多选题
    With regard to bridges and switches, which of the following statements are true?（）
    A

    Switches are primarily software based while bridges are hardware based.

    B

    Both bridges and switches forward Layer 2 broadcasts.

    C

    Bridges are frequently faster than switches.

    D

    Switches typically have a higher number of ports than bridges.

    E

    Bridges define broadcast domain while switches define collision domains.

    F

    Both bridges and switches make forwarding decisions based on Layer 2 addresses.


    正确答案： A,E
    解析： 暂无解析

  • 第21题：

    多选题
    Which of the following characteristics are true assuming you are troubleshooting a networkcurrently enabled for VRRP？（Choose all that apply.）（）
    A

    The network is load balancing among different members of the VRRP group

    B

    The default hello timers are 1 second

    C

    The interface IP address is being used as the virtual IP address

    D

    There are several routers in the group simultaneously forwarding traffic for the group

    E

    It is a Cisco Proprietary protocol

    F

    The default hello timers are 3 seconds


    正确答案： E,D
    解析： 暂无解析

  • 第22题：

    多选题
    Which two statements are true regarding an Ethernet collision domain?（）
    A

    If a switch is used, the collision domain is limited to each device and the switch

    B

    If a hub is used, the collision domain is limited to each device and the hub

    C

    If a hub is used, the collision domain includes all devices connected to the hub

    D

    If a switch is used, the collision domain includes all devices connected to the switch


    正确答案： D,C
    解析： 暂无解析

  • 第23题：

    单选题
    Which statement is true regarding an Ethernet collision domain?（）
    A

    If a router is used, the collision domain includes all devices connected to the router.

    B

    If a hub is used, the collision domain is limited to each device and the hub.

    C

    If a switch is used, the collision domain is limited to each device and the switch.

    D

    If a bridge is used, the collision domain includes all devices connected to the bridge.


    正确答案： B
    解析： 暂无解析

相关内容