单选题An administrator reboots a ten drive server, with a RAID 10 array, after a power failure and receives an error logical drive failed. Which of the following is the MOST likely cause?（）A Corrupt file system tableB Backplane failureC Multiple drive failur

第1题：

An administrator needs the fastest read/write capabilities with the most redundancy， cost is not afactor. The current data requirement is 750GB but will double in the next year. Which of the following BEST meets these requirements？ （）

• A、 Use RAID 1 with ten 300GB hard drives.
• B、 Use RAID 6 with seven 300GB hard drives.
• C、 Use RAID 5 with six 300GB hard drives.
• D、 Use RAID 10 with ten 300GB hard drives.

第2题：

A server contains a 3 disk RAID 5 array. The red LED is illuminated on one of the drives. Which of the following should the server administrator perform？（）

• A、Replace the drive
• B、Restore the drive from backup
• C、Reboot the server
• D、Reconfigure RAID 5 to RAID 10

第3题：

A server has had a drive fail in its storage RAID set.  The administrator swaps the drive with a replacement and the RAID set does not automatically start to rebuild the replaced drive.  Which ofthe following utilities would MOST likely be used to initialize the rebuilding of the replace mentdrive？（）

• A、Net use
• B、Array management
• C、Fdisk
• D、Disk Management Plug-in

第4题：

A staff member reports that they cannot access the shared folder on the network； however， other staff members are reporting that they can access the shared folder. Which of the following is the BEST way to identify the problem？（）

• A、The administrator should monitor all traffic between the staff member and the server.
• B、The administrator should reconfigure the RAID configuration to allow more space.
• C、The administrator should map a drive using the net use command.
• D、The administrator should allow the staff member to use a USB drive.

第5题：

An administrator adds a new SATA hard drive into a functional server and attempts to boot the server. The server will no longer boot into the operating system. The administrator checks all the connections and reboots the server. The server still will not load the operating system.  Which of the following is the MOST probable cause？（）

• A、The BIOS is set with the wrong boot order.
• B、The jumpers have not been set on the hard drive.
• C、The hard drive is not compatible with the system board.
• D、The boot.ini file needs to be modified.

第6题：

An administrator reboots a ten drive server， with a RAID 10 array， after a power failure and receives an error logical drive failed.  Which of the following is the MOST likely cause？（）

• A、 Corrupt file system table
• B、 Backplane failure
• C、 Multiple drive failure
• D、 Bad cable

第7题：

An administrator has replaced a faulty drive in a server using software RAID. The drive needs to now be partitioned before being added back to the array. Which of the following tools should the administrator use to accomplish this？（）

• A、chkdsk
• B、mount
• C、fsck
• D、diskpart

第8题：

第9题：

第10题：

第11题：

第12题：

第13题：

An administrator just installed a new RAID controller card into a server. The firmware is current for the controller card. When the server is powered up the administrator notices that the RAID controller card is not recognized during POST. Which of the following is the cause of the problem？（）

• A、The hard drives were not plugged into the server correctly.
• B、The controller driver is outdated and needs to be updated from the OEMs website.
• C、The firmware for the server is too old and does not support the new RAID controller card.
• D、The cable from the controller to the hard drive backplane is not connected.

第14题：

A system administrator needs to maintain 1.2TB of storage for a database server. There are six 250GB drives available in the server for storage space. Which of the following RAID configurations would be the BEST choice given that performance and fault tolerance are important factors?（）

• A、RAID 1 across drive pairs totaling 3 pairs
• B、RAID 5 across all 6 drives
• C、RAID 10 across all 6 drives
• D、RAID 0 across all 6 drives

第15题：

An administrator has added a new hard drive to a server that is running out of space on its C Drive and is experiencing slow performance.  The administrator needs to free up space on the C Drive.Which of the following is the BEST action for the administrator to take to free up space on the drive？（）

• A、Move the page file to the new drive.
• B、Copy the system32 directory to the new drive.
• C、Convert the C drive to a basic disk.
• D、Setup a software RAID to mirror the C drive.

第16题：

An administrator is configuring RAID 1 in a server.  The administrator has been given two matching 80GB SATA-2 hard drives， two SATA-2 cables， and a SATA-2 RAID adapter.  How should the administrator BEST configure these drives？（）

• A、Install one drive on the first channel and install the second drive on the second channel.
• B、Install one drive on the first cable， on the first channel. Install the second drive on the secondcable， on the second channel.
• C、Install both drives on the same channel. Cable both drives as the primary master on the samecable.
• D、Install both drives on the same channel. On the same cable one drive should be set as primaryslave and the other drive as the primary master.

第17题：

A file server is setup in a RAID 5 configuration.Recently there was a power failure in the server room while a user was transferring a document from one drive on the server to another drive on the same server.Unfortunately their UPS was in repair during this outage， and the file is now corrupt.Which of the following can be done to prevent this situation in the future？（）

• A、Increase the memory on the server.
• B、Reconfigure drives to a RAID 0+1.
• C、Install a battery backed write cache module in the system.
• D、Instruct the user to save to the local system instead of to the server.

第18题：

An administrator is installing Windows Server 2003 via CD on a new server with an SAS RAID array.When the administrator reaches the option to select the target installation drive， there are no drives listed. Which of the following is the FIRST thing the administrator should do？（）

• A、 Restart the installation via WDS.
• B、 Shut down the server and check that all RAID drives are connected properly.
• C、 Restart the installation from CD and press F6 to install RAID drivers.
• D、 Go into the BIOS and set all RAID drives to compatibility mode.

第19题：

第20题：

第21题：

第22题：

第23题：

第24题：