多选题A network administrator needs to configure port security on a switch.which two statements are true?（）AThe network administrator can apply port security to dynamic access portsBThe network administrator can configure static secure or sticky secure mac a

题目
多选题
A network administrator needs to configure port security on a switch.which two statements are true?（）
A

The network administrator can apply port security to dynamic access ports

B

The network administrator can configure static secure or sticky secure mac addresses in the voice vlan.

C

The sticky learning feature allows the addition of dynamically learned addresses to the running configuration.

D

The network administrator can apply port security to EtherChannels.

E

When dynamic mac address learning is enabled on an interface,the switch can learn new addresses,up to the maximum defined.

相似考题

1.The network administrator has configured port security on a Ezonexam switch. Why would a network administrator configure port security on this Ezonexam device?A．To prevent unauthorized hosts from getting access to the LANB．To limit the number of Layer 2 broadcasts on a particular switch portC．To prevent unauthorized Telnet or SSH access to a switch portD．To prevent the IP and MAC address of the switch and associated portsE．None of the above

2.A network administrator has configured source NAT, translating to an address that is on a locally connected subnet.The administrator sees the translation working, but traffic does not appear to come back.What is causing the problem?（）A. The host needs to open the telnet port.B. The host needs a route for the translated address.C. The administrator must use a proxy-arp policy for the translated address.D. The administrator must use a security policy, which will allow communication between the zones.

3.A network administrator needs to configure a serial link between the main office and a remote location. The router at the remote office is a non-Cisco router.How should the network administrator configure the serial interface of the main office router to make the connection?（）A.B.C.D.

4.The Ezonexam network administrator wants to ensure that only a single web server can connect to pot Fa0/1 on a catalyst switch. The server is plugged into the switch's Fast Eth. 0/1 port and the network administrator is about to bring the server online. What can the administrator do to ensure that only the MAC address of this server is allowed by switch port Fa0/1? (Choose two)A．Configure port Fa0/1 to accept connections only from the static IP address of the serverB．Configure the MAC address of the server as a static entry associated with port Fa0/1C．Employ a proprietary connector type on Fa0/1 that is incomputable with other host connectorsD．Configure port security on Fa0/1 to reject traffic with a source MAC address other than that of the serverE．Bind the IP address of the server to its MAC address on the switch to prevent other hosts from spoofing the server IP address

更多“A network administrator needs to configure port security on”相关问题

  • 第1题：

    Why would a network administrator configure port security on a switch?（）

    • A、To prevent unauthorized Telnet access to a switch port.
    • B、To limit the number of Layer 2 broadcasts on a particular switch port.
    • C、To prevent unauthorized hosts from accessing the LAN.
    • D、To protect the IP and MAC address of the switch and associated ports.
    • E、To block unauthorized access to the switch management interfaces over common TCP ports.

    正确答案:C

  • 第2题：

    A network administrator needs to configure port security on a switch.which two statements are true？（）

    • A、The network administrator can apply port security to dynamic access ports
    • B、The network administrator can configure static secure or sticky secure mac addresses in the voice vlan.
    • C、The sticky learning feature allows the addition of dynamically learned addresses to the runningconfiguration.
    • D、The network administrator can apply port security to EtherChannels.
    • E、When dynamic mac address learning is enabled on an interface，the switch can learn new addresses，up to the maximum defined.

    正确答案:C,E

  • 第3题：

    A network administrator needs to configure port security on a switch.which two statements are true?（）

    • A、The network administrator can apply port security to dynamic access ports
    • B、The network administrator can configure static secure or sticky secure mac addresses in the voice vlan.
    • C、The sticky learning feature allows the addition of dynamically learned addresses to the running configuration.
    • D、The network administrator can apply port security to EtherChannels.
    • E、When dynamic mac address learning is enabled on an interface,the switch can learn new addresses,up to the maximum defined.

    正确答案:C,E

  • 第4题：

    A network administrator must configure 200 switch ports to accept traffic from only the currently attached host devices.What would be the most efficient way to configure MAC-level security on all these ports？ （）

    • A、Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security mac-address command.
    • B、Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security mac-address command.
    • C、Use the switchport port-security MAC address sticky command on all the switch ports that have end devices connected to them.
    • D、Use show mac-address-table to determine the addresses that are associated with each port and then enter the commands on each switch for MAC address port-security.

    正确答案:C

  • 第5题：

    A network administrator must configure 200 switch ports to accept traffic from only the currently attached host devices. What would be the most efficient way to configure MAC-level security on all these ports?（）

    • A、Visually verify the MAC addresses and then telnet to the switches to enter the switchport-port security mac-address command
    • B、Have end users e-mail their MAC addresses. Telnet to the switch to enter the switchport-port security mac-address command
    • C、Use the switchport port-security MAC address sticky command on all the switch ports that have end devices connected to them
    • D、Use show mac-address-table to determine the addresses that are associated with each port and then enter the commands on each switch for MAC address port-security

    正确答案:C

  • 第6题：

    You need to configure port security on switch R1.  Which two statements are true about this  technology？ （）

    • A、 Port security can be configured for ports supporting VoIP.
    • B、 With port security configured， four MAC addresses are allowed by default.
    • C、 The network administrator must manually enter the MAC address for each device in order for  the switch to allow connectivity.
    • D、  Withsecurity configured， only one MAC addresses is allowed by default.  
    • E、 Port security cannot be configured for ports supporting VoIP.

    正确答案:A,D

  • 第7题：

    An administrator replaces the network card in a web server. After replacing the network card some users can access the server but others cannot. Which of the following is the FIRST thing the administrator should check?（）

    • A、Default gateway
    • B、The ports on the switch
    • C、Port security on the server's switch port
    • D、Ethernet cable

    正确答案:A

  • 第8题：

    You are the network administrator for your company. A Windows Server 2003 computer named Router11 is used to connect the network to the Internet. You find out that some computers on the network are infected with a worm， which occasionally sends out traffic to various hosts on the Internet. This traffic always uses a certain source TCP port number.You need to identify which computers are infected with the worm. You need to configure a solution on Router11 that will perform the following two tasks： Detect and identify traffic that is sent by the worm.   Immediately send a notification to a network administrator that the infected computer needs to be repaired.  What should you do？（）

    • A、Configure a WMI event trigger.
    • B、Configure a Network Monitor capture filter.
    • C、Configure a Network Monitor trigger.
    • D、Configure a System Monitor alert.

    正确答案:C

  • 第9题：

    单选题
    You are a security administrator for your company. The network consists of a single Active Directory domain. All client computers run Windows XP Professional. All servers run Windows Server 2003. All computers on the network are members of the domain.    Traffic on the network is encrypted by IPSec. The domain contains a custom IPSec policy named Lan Security that applies to all computers in the domain. The Lan Security policy does not allow unsecured communication with non-lPSec-aware computers. The company’s written security policy states that the configuration of the domain and the configuration of the Lan Security policy must not be changed. The domain contains a multihomed server named Server1. Server1 isconnected to the company network， and Server1 is also connected to a test network. Currently， the Lan Security IPSec policy applies to network traffic on both network adapters in Server1. You need to configure Server1 so that it communicates on the test network without IPSec security. Server1 must still use the Lan Security policy when it communicates on the company network.  How should you configure Server1？（）
    A

     Configure a packet filter for the network adapter on the test network to block the Internet Key Exchange （IKE） port.

    B

     Configure the network adapter on the test network to disable IEEE 802.1x authentication.

    C

     Configure the network adapter on the test network to enable TCP/IP filtering， and then permit all traffic.

    D

     Use the netsh command to assign a persistent IPSec policy that permits all traffic on the network adapter on the test.

    E

     Assign an IPSec policy in the local computer policy that permits all traffic on the network adapter on the test.


    正确答案： A
    解析： 暂无解析

  • 第10题：

    多选题
    You need to configure port security on switch R1.  Which two statements are true about this  technology？ （）
    A

    Port security can be configured for ports supporting VoIP.

    B

    With port security configured， four MAC addresses are allowed by default.

    C

    The network administrator must manually enter the MAC address for each device in order for  the switch to allow connectivity.

    D

      Withsecurity configured， only one MAC addresses is allowed by default.

    E

    Port security cannot be configured for ports supporting VoIP.


    正确答案： A,E
    解析： 暂无解析

  • 第11题：

    多选题
    Refer to the exhibit. A junior network administrator was given the task of configuring port security on SwitchA to allow only PC_A to access the switched network through port fa0/1. If any other device is detected, the port is to drop frames from this device. The administrator configured the interface and tested it with successful pings from PC_A to RouterA, and then observes the output from these two show commands.Which two of these changes are necessary for SwitchA to meet the requirements? （）
    A

    Port security needs to be globally enabled.

    B

    Port security needs to be enabled on the interface.

    C

    Port security needs to be configured to shut down the interface in the event of a violation.

    D

    Port security needs to be configured to allow only one learned MAC address.

    E

    Port security interface counters need to be cleared before using the show command.

    F

    The port security configuration needs to be saved to NVRAM before it can become active.


    正确答案： E,B
    解析： 暂无解析

  • 第12题：

    单选题
    For security reasons, the network administrator needs to prevent pings into the corporate networks from hosts outside the internetwork. Which protocol should be blocked with access control lists？（）
    A

    IP

    B

    ICMP

    C

    TCP

    D

    UDP


    正确答案： A
    解析： 暂无解析

  • 第13题：

    Why would a network administrator configure port security on a switch?（）

    • A、to prevent unauthorized Telnet access to a switch port
    • B、to limit the number of Layer 2 broadcasts on a particular switch port
    • C、to prevent unauthorized hosts from accessing the LAN
    • D、to protect the IP and MAC address of the switch and associated ports
    • E、to block unauthorized access to the switch management interfaces over common TCP ports

    正确答案:C

  • 第14题：

    The network security policy requires that only one host be permitted to attach dynamically to each switch interface. If that policy is violated, the interface should shut down. Which two commands must the network administrator configure on the 2950 Catalyst switch to meet this policy (Choose two.)（）。

    • A、Switch1(config-if)# switchport port-security maximum 1
    • B、Switch1(config)# mac-address-table secure
    • C、Switch1(config)# access-list 10 permit ip host
    • D、Switch1(config-if)# switchport port-security violation shutdown
    • E、Switch1(config-if)# ip access-group 10

    正确答案:A,D

  • 第15题：

    A network administrator wants to ensure that only the server can connect to port Fa0/1 on a Catalyst switch. The server is plugged into the switch Fa0/1 port and the network administrator is about to bring the server online. What can the administrator do to ensure that only the MAC address of the server is allowed by switch port Fa0/1?（）

    • A、Configure port Fa0/1 to accept connections only from the static IP address of the server.
    • B、Employ a proprietary connector type on Fa0/1 that is incompatible with other host connectors.
    • C、Configure the MAC address of the server as a static entry associated with port Fa0/1.
    • D、Bind the IP address of the server to its MAC address on the switch to prevent other hosts from spoofing the server IP address.
    • E、Configure port security on Fa0/1 to reject traffic with a source MAC address other than that of the server.
    • F、Configure an access list on the switch to deny server traffic from entering any port other than Fa0/1.

    正确答案:C,E

  • 第16题：

    Refer to the exhibit. A junior network administrator was given the task of configuring port security on SwitchA to allow only PC_A to access the switched network through port fa0/1. If any other device is detected, the port is to drop frames from this device. The administrator configured the interface and tested it with successful pings from PC_A to RouterA, and then observes the output from these two show commands.Which two of these changes are necessary for SwitchA to meet the requirements? （）

    • A、Port security needs to be globally enabled.
    • B、Port security needs to be enabled on the interface.
    • C、Port security needs to be configured to shut down the interface in the event of a violation.
    • D、Port security needs to be configured to allow only one learned MAC address.
    • E、Port security interface counters need to be cleared before using the show command.
    • F、The port security configuration needs to be saved to NVRAM before it can become active.

    正确答案:B,D

  • 第17题：

    The network security policy requires that only one host be permitted to attach dynamically to each switch interface. If that policy is violated, the interface should shut down. Which two commands must the network administrator configure on the 2950 Catalyst switch to meet this policy?（）

    • A、TestKing1(config-if)# switchport port-security maximum 1
    • B、TestKing1(config)# mac-address-table secure
    • C、TestKing1(config)# access-list 10 permit ip host
    • D、TestKing1(config-if)# switchport port-security violation shutdown
    • E、TestKing1(config-if)# ip access-group 10

    正确答案:A,D

  • 第18题：

    An administrator replaces the network card in a web server. After replacing the network card some users can access the server but others cannot.  Which of the following is the FIRST thing the administrator should check？（）

    • A、 Default gateway
    • B、 The ports on the switch
    • C、 Port security on the servers switch port
    • D、 Ethernet cable

    正确答案:A

  • 第19题：

    An administrator needs to configure a server to restrict mail traffic to an application server for security reasons.  Which of the following techniques can be used to manage this？（）

    • A、 PAT
    • B、 ACLs
    • C、 Subnet masking
    • D、 Port blocking

    正确答案:B

  • 第20题：

    单选题
    An administrator needs to configure a server to restrict mail traffic to an application server for security reasons.  Which of the following techniques can be used to manage this？（）
    A

     PAT

    B

     ACLs

    C

     Subnet masking

    D

     Port blocking


    正确答案： A
    解析： 暂无解析

  • 第21题：

    单选题
    An administrator replaces the network card in a web server. After replacing the network card some users can access the server but others cannot.  Which of the following is the FIRST thing the administrator should check？（）
    A

     Default gateway

    B

     The ports on the switch

    C

     Port security on the servers switch port

    D

     Ethernet cable


    正确答案： D
    解析： 暂无解析

  • 第22题：

    单选题
    A network administrator has configured source NAT, translating to an address that is on a locally connected subnet.The administrator sees the translation working, but traffic does not appear to come back. What is causing the problem?（）
    A

    The host needs to open the telnet port.

    B

    The host needs a route for the translated address.

    C

    The administrator must use a proxy-arp policy for the translated address.

    D

    The administrator must use a security policy, which will allow communication between the zones.


    正确答案： C
    解析： 暂无解析

  • 第23题：

    单选题
    Why would a network administrator configure port security on a switch（）。
    A

    to prevent unauthorized Telnet access to a switch port

    B

    to limit the number of Layer 2 broadcasts on a particular switch port

    C

    to prevent unauthorized hosts from accessing the LAN

    D

    to protect the IP and MAC address of the switch and associated ports

    E

    to block unauthorized access to the switch management interfaces over common TCP ports


    正确答案： E
    解析： 暂无解析

  • 第24题：

    单选题
    Why would a network administrator configure port security on a switch?（）
    A

    To prevent unauthorized Telnet access to a switch port.

    B

    To limit the number of Layer 2 broadcasts on a particular switch port.

    C

    To prevent unauthorized hosts from accessing the LAN.

    D

    To protect the IP and MAC address of the switch and associated ports.

    E

    To block unauthorized access to the switch management interfaces over common TCP ports.


    正确答案： D
    解析： 暂无解析

相关内容