多选题Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? （）ARouter1 has specific boot system command that instruct it to load IOS from TFTP server.BRouter1 is acting as a TFTP server for other rout

题目
多选题
Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? （）
A

Router1 has specific boot system command that instruct it to load IOS from TFTP server.

B

Router1 is acting as a TFTP server for other routers.

C

Router1 cannot locate a valid IOS image in flash memory.

D

Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.

E

Cisco routers will first attempt to load a image from TFTP for management purposes.

相似考题

1.Refer to the exhibit. OSPF is configured on all routers in the network. Area 5 is configured as an NSSA areA. The RIPv2 routes are redistributed into the OSPF domain on router R5. What two types of LSAs will be originated by router R5?（）A. type 1 Router LSAB. type 2 Network LSAC. type 3 Network Summary LSAD. type 4 ASBR Summary LSAE. type 5 AS External LSAF. type 7 NSSA External LSA

2.Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcastB. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - pointC. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253

3.Refer to the exhibit. A network administrator wants to reduce the number of OSPF routes advertised from Area 1 into Area 2. As the router configuration specialist, what two things would you do to accomplish this goal?（）A. Enter the configuration on router B1.B. Enter the configuration on router B4.C. On the same router, enter the Summary - address 10.10.1.0 255.255.255.128 subcommand.D. On the same router, enter the Area 1 range 10.10.1.0 255.255.255.128 subcommand.E. On the same ro uter, enter the Area 2 range 10.10.1.0 255.255.255.128 subcommand.

4.Refer to the exhibit. EIGRP has been configured on router D. Router C is performing mutual redistribution between EI GRP and OSPF. While verifying that the redistribution is functioning properly, you discover that while router C has all of the EIGRP routes in its routing table, router A does not have any routes from the EIGRP domain. What on router C may be the cause o f the problem?（）A. The no auto - summary command needs to be added under router eigrp 1B. The subnets keyword was not included in the redistribute command under router ospf 1C. The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router AD. The default - information originate command needs to be added under router ospf 1E. The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF

更多“Refer to the exhibit. For what two reasons has the router lo”相关问题

  • 第1题：

    Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）

    A. All OSPF implementations must have at le ast one interface in area 0.

    B. You are attempting to run in the broadcast mode over an NBMA interface.

    C. Both routers are configured to function as a BDR; therefore, there is no DR router.

    D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.

    E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.


    参考答案：E

  • 第2题：

    Refer to the parti al configurations in the exhibit. What address is utilized for DR and BDR identification on Router1?()

    A. the serial 1/1 address

    B. the serial 2/0 address

    C. a randomly generated internal address

    D. the configured router - id address


    参考答案：D

  • 第3题：

    Refer to the exhibit. What three statements are true about the IS － IS configuration?()

    A.The router is in area 49.0001.0002

    B.The router acts as a Level 1 - 2 router

    C.CLNS routing is enable d for the router

    D.The router has a system ID of 0003.0004

    E.The interfaces have a functional IS - IS configuration

    F.The network service access point selector (NSEL) byte has a value of 0


    参考答案：B, E, F

  • 第4题：

    Refer to the exhibit. Network 10.0.0.0／8 is being advertised to autonomous system 65550 via both external links. Which statement about the preferred path to the 10.0.0.0／8 network is true? ()

    A. Router R2 will be preferred because it has the higher neighbor IP address.

    B. Router R2 will be preferr ed because its neighbor has a lower autonomous system number.

    C. Router R1 will be preferred because it has a lower local preference.

    D. Router R2 will be preferred because it has a higher local preference.

    E. Router R1 will be preferred because its nei ghbor has the higher autonomous system number.

    F. Router R1 will be preferred because it has the lower neighbor IP address.


    参考答案：D

  • 第5题：

    Refer to the exhibit. Which st atement is true?()

    A. Router RTA is the BDR

    B. Router RTA is directly connected to interface 192.168.45.1

    C. Neighbor 192.168.45.1 has changed its OSPF priority number

    D. Router RTA and neighbor 192.168.45.2 are exchanging OSPF LSAs


    参考答案：A

  • 第6题：

    Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional configur ation statement should be included on router R4 to advertise a default route to its neighbors?()

    A. R4(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1

    B. R4(config)# ip default - network 10.0.0.0

    C. R4(config - router)# default -information originate

    D. R4(conf ig)# ip route 10.0.0.0 255.0.0.0 10.1.1.1


    参考答案：B

  • 第7题：

    Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? ()

    A.Router1 has specific boot system command that instruct it to load IOS from TFTP server.

    B.Router1 is acting as a TFTP server for other routers.

    C.Router1 cannot locate a valid IOS image in flash memory.

    D.Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.

    E.Cisco routers will first attempt to load a image from TFTP for management purposes.


    参考答案：A, C

  • 第8题：

    Refer to the exhibit. What does the (*) represent in the output?()

    A.Packet is destined for a local interface to the router.

    B.Packet was translated, but no response was received from the distant device.

    C.Packet was not translated, because no additional ports are available.

    D.Packet was translated and fast switched to the destination.


    参考答案：D

  • 第9题：

    Refer to the exhibit. The two connected ports on the switch are not turning orange or green. What would be the most effective steps to troubleshoot this physical layer problem?（）

    • A、Ensure that the Ethernet encapsulations match on the interconnected router and switch ports.
    • B、Ensure that cables A and B are straight-through cables.
    • C、Ensure cable A is plugged into a trunk port.
    • D、Ensure the switch has power.
    • E、Reboot all of the devices.
    • F、Reseat all cables.

    正确答案:B,D,F

  • 第10题：

    Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? （）

    • A、Router1 has specific boot system command that instruct it to load IOS from TFTP server.
    • B、Router1 is acting as a TFTP server for other routers.
    • C、Router1 cannot locate a valid IOS image in flash memory.
    • D、Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.
    • E、Cisco routers will first attempt to load a image from TFTP for management purposes.

    正确答案:A,C

  • 第11题：

    多选题
    Refer to the exhibit. For what two reasons has the router loaded its IOS image from the location that is shown? （）
    A

    Router1 has specific boot system command that instruct it to load IOS from TFTP server.

    B

    Router1 is acting as a TFTP server for other routers.

    C

    Router1 cannot locate a valid IOS image in flash memory.

    D

    Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.

    E

    Cisco routers will first attempt to load a image from TFTP for management purposes.


    正确答案： E,C
    解析： 暂无解析

  • 第12题：

    单选题
    Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）
    A

    As numbers must be changed to match on all the routers.

    B

    Loopback interface must be configured so a DR is elected.

    C

    The no auto-summary command is needed on Router A and Router C.

    D

    Router B needs to have two network statements, one for each connected network.


    正确答案： B
    解析： 暂无解析

  • 第13题：

    Refer to the exhibit. Looking at the topology diagram and the partial router configurations shown, which statement is true? ()

    A.The NProuter has two OSPF neighbors in the "Full" adjacency state

    B.The NProuter serial0/0 interface has the OSPF dead timer set to 10 seconds

    C.The NProuter serial0/0 interface has been configured with an OSPF network type of "pointtopoint"

    D.The 10.1.1.1 and 10.1.1.2 routers are not using the default OSPF dead and hello timers setting

    E.The "Mismatched" error is caus ed by the expiration of the OSPF timers


    参考答案：E

  • 第14题：

    Refer to the exhibit. On the basis of the output, what two conclusions can be reached?()

    A. The default administrative distance has been changed.

    B. IS - IS is not enabled.

    C. Three physical interfaces are taking part in integrated IS - IS.

    D. IS - IS is not redistributing any oth er routing protocols.

    E. There are two neighboring routers sending IS - IS routing information.

    F. Address summarization is configured.


    参考答案：D, E

  • 第15题：

    Refer to the exhibit. What two statements are true?()

    A. This is the designated router (DR) on the FastEthernet 0/0 link.

    B. The output was generated by the show ip interface c ommand.

    C. The router was configured with the commands:r outer ospf 1 network 172.16.6.0 0.0.0.255 area 1

    D. The IP address of the backup designated router (BDR) is FE80::205:5FFF:FED3:5808.

    E. Interface FastEthernet 0/0 was configured with the ipv6 o spf 1 area 1 command.

    F. OSPF version 2 has been enabled to support IPv6.


    参考答案：D, E

  • 第16题：

    Refer to the exhibit. Router RT - 1 and router RT - 2 both advertise network 131.25.0.0/16 to routerRT - 3 via internal BGP. What is the reason that router RT - 3 chose router RT - 1 as its best path tonetwork 131.25.0.0/16.（）

    A. It has a better router ID

    B. It advertises a lower autonomous system

    C. It advertises t he best AS - path

    D. It advertises the best local preference

    E. It advertises the best origin code

    F. It advertises the best MED


    参考答案：A

  • 第17题：

    Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However, R1 does not show R2 as a neighbor and does not accept routing updates from R2.What could be the cause of the problem?()

    A. The no auto - summary command has not been issued under the EIGRP process on both routers.

    B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.

    C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.

    D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.


    参考答案：D

  • 第18题：

    Refer to the exhibit. When running OSPF, What would cause router A not to form an adjacency with router B?()

    A.The loopback addresses are on different subnets

    B.The value of the dead timers on the router are different

    C.Route summarization is enabled on both routers

    D.The process indentifier on router A is different than the process identifier on router B


    参考答案：B

  • 第19题：

    Refer to the exhibit. The two exhibit devices are the only Cisco devices on the network. The serial network between the two devices has a mask of 255.255.255.252. Given the output that is shown, what three statements are true of these devices? （）

    A.The Manchester serial address is 10.1.1.1

    B.The Manchester serial address is 10.1.1.2

    C.这个Manchester路由器串口地址为：10.1.12

    D.The London router is a Cisco 2610.

    E.The Manchester router is a Cisco 2610.

    F.The CDP information was received on port Serial0/0 of the Manchester router.

    G.The CDP information was sent by port Serial0/0 of the London Router.


    参考答案：A, D, F

  • 第20题：

    Refer to the exhibit. When running EIGRP, What is required for RouterA to exchange routing updates with RouterC?（）

    • A、As numbers must be changed to match on all the routers.
    • B、Loopback interface must be configured so a DR is elected.
    • C、The no auto-summary command is needed on Router A and Router C.
    • D、Router B needs to have two network statements, one for each connected network.

    正确答案:A

  • 第21题：

    What are two reasons that a network administrator would use access lists? (Choose two.) （）。

    • A、to control vty access into a router  
    • B、to control broadcast traffic through a router  
    • C、to filter traffic as it passes through a router  
    • D、to filter traffic that originates from the router  
    • E、to replace passwords as a line of defense against security incursions 

    正确答案:A,C

  • 第22题：

    单选题
    Refer to the exhibit. Given the output for this command, if the router ID has not been manually set, what router ID will OSPF use for this RouterD?（）
    A

    10.1.1.2

    B

    10.154.154.1

    C

    172.16.5.1

    D

    192.168.5.3


    正确答案： B
    解析： 暂无解析

  • 第23题：

    多选题
    HSRP has been configured between two Company devices.  Which of the following describe  reasons for deploying HSRP？ （）
    A

    HSRP provides redundancy and fault tolerance

    B

    HSRP allows one router to automatically assume the function of the second router if the second  router fails

    C

    HSRP allows one router to automatically assume the function of the second router if the second  router starts

    D

    HSRP provides redundancy and load balancing


    正确答案： C,B
    解析： 暂无解析

  • 第24题：

    多选题
    Refer to the exhibit. The two connected ports on the switch are not turning orange or green. What would be the most effective steps to troubleshoot this physical layer problem?（）
    A

    Ensure that the Ethernet encapsulations match on the interconnected router and switch ports.

    B

    Ensure that cables A and B are straight-through cables.

    C

    Ensure cable A is plugged into a trunk port.

    D

    Ensure the switch has power.

    E

    Reboot all of the devices.

    F

    Reseat all cables.


    正确答案： C,F
    解析： 暂无解析

相关内容