Neighbor table
SPF table
RTP table
Topology table
Query table
DUAL table
第1题:
Which table of EIGRP route information are held in RAM and maintained through the use of hello and update packets?()
第2题:
In EIGRP, what kind of route information is stored in the RAM of the router and maintained by way of hello packets and update packets?()
第3题:
Which statements are true about EIGRP successor routes? ()
第4题:
Which two statements are true regarding EIGRP?()
第5题:
Which of the following are methods EIGRP uses to initially populate (seed) its EIGRP topology table, before learning topology data from neighbors?()
第6题:
Which tables of EIGRP route information are held in RAM and maintained through the use of hello and update packets (Choose two.)()。
第7题:
A successor route is used by EIGRP to forward traffic to a destination.
Successor routes are saved in the topology table to be used if the primary route fails.
Successor routes are flagged as active in the routing table.
A successor route may be backed up by a feasible successor route.
Successor routes are stored in the neighbor table following the discovery process.
Successors are not used in EIGRP.
第8题:
An error will result because a router cannot be configured with an EIGRP variance of 3 becausethe maximum variance number is 2
The successor route will end up in the routing table, and so will any route with a metric at mostthree times greater than the value of the successor’s metric
EIGRP will only advertise routes that are within three hops of the current router
The successor route will end up in the routing table, and so will any route with a metric at leastone third the value of the successor’s metric
The best three routes with equal cost paths will end up in the routing table
The successor route will be any route with three times the value of the advertised distance
第9题:
Neighbor Table
SRF Table
RTP Table
Topology Table
Query Table
Dual Table
第10题:
Neighbor Table
SRF Table
RTP Table
Topology Table
Query Table
Dual Table
第11题:
a primary route,stored in the routing table
a backup route,stored in the routingt able
a backup route,stored in the topology table
A primary route,stored in the topology table
第12题:
Which two statements about the EIGRP DUAL process are correct?()
第13题:
Which two table types are CEF components?()
第14题:
A router has been configured with an EIGRP variance of 3. Which of the following statements istrue?()
第15题:
Which statements are true about EIGRP successor routes (Choose two.)()。
第16题:
In EIGRP, what kind of route information is stored in RAM and maintained by way of hello packets and update packets?()
第17题:
An EIGRP route will go active if there are no successors or feasible successors in the EIGRP topology table.
An EIGRP route will go passive if there are no successors in the EIGRP topology table.
DUAL will trigger an EIGRP query process while placing the flapping routes in the holddown state.
A feasible successor in the EIGRP topology table can become the successor only after all the query requests have been replied to.
The stuck in active state is caused when the wait for the query replies have timed out.
EIGRP queries are sent during the loading state in the EIGRP neighbor establishment process.
第18题:
neighbor table
SPF table
RTP table
topology table
query table
DUAL table
第19题:
Passive routes are in the process of being calculated by DUAL.
EIGRP supports VLSM, route summarization, and routing update authentication.
EIGRP exchanges full routing table information with neighboring routers with every update.
If the feasible successor has a higher advertised distance than the successor route, it becomes the primary route.
A query process is used to discover a replacement for a failed route if a feasible successor is not identified from the current routing information.
第20题:
Neighbor table
SPF table
RTP table
Topology table
Query table
DUAL table
第21题:
By adding all subnets listed by the show ip route connected command
By adding the subnets of working interfaces over which static neighbors have been defined
By adding subnets redistributed on the local router from another routing source
By adding all subnets listed by the show ip route static command