It prevents message looping, Session Advertisement (SA)messages must be RPF checked
RPF check should be done against the route to the source S of the corresponding PIM-SM domain
RPF check should be done against the route to the Rendez-vous Point of the corresponding PIM-SM domain,which originated the SA
RPF checking Session Advertisement (SA) messages will cause message looping
第1题:
Which two statements are tru e about the rendezvous point (RP) in a multicast network?()
第2题:
Which two statements are true about the RMAN validate database command?()
第3题:
In order to configure two routers as anycast RPs, which of these requirements, af a minimum, must besatisfied?()
第4题:
Which three statements about anycast RP are true? ()
第5题:
Which two of these are characteristics of multicast routing? ()
第6题:
Which two statements are true about the forwarding table?()
第7题:
Which two statements are true about pool-based source NAT? ()(Choose two.)
第8题:
The multicast sources must register with the RP to form the multicast distribution tree.
An RP is required only in networks running Protocol Independent Multicast dense mode (PIM DM).
The multicast receivers must register with the RP to form the multicast distribution tree.
An RP is required only in networks running Protocol Independent Multicast sparse mode (PIM SM).
An RP is required only in networks running Protocol Independent Multicast sparse - dense mode (PIM - SDM).
To form the multicast distribution tree, the multicast sources register with and the receivers join the RP.
第9题:
Is best suited for applications that are in the one-to-many category.
SSM uses shortest path trees only.
The use of SSM is recommended when there are many sources and it is desirable to keep the amount of mroute state in the routers in the network to a.
There are no RPs to worry about.
第10题:
It is used for PIM control traffic
It is optionally configured for a high bandwidth multicast source to reduce multicast traffic replication to uninterested PE routers
Within the VPF configuration in the PE router, multiple Default MDT groups are configured so each VPF can support multiple multicast sources
There is a reduced multicast state in the MPLS core P routers
When multicast traffic exceeds a certain configured threshold, traffic from the Data MDT is switched to the Default MDT to conserve bandwidth
第11题:
The forwarding table lists each source protocol and preference for each destination
The forwarding table constains only active routes
The forwarding table is used to process transit packets
The forwarding table is stored in compact flash
第12题:
PAT is not supported.
PAT is enabled by default.
It supports the address-persistent configuration option.
It supports the junos-global configuration option.
第13题:
Which two of these multicast deployments are most susceptible to attacks from unknown sources?()
第14题:
Which two statements about RPF checks in Multicast Source Discovery Protocol (MSDP) are true?()
第15题:
Which three statements are true about Source Specific Multicast?()
第16题:
In order to configure two routers as anycast RPs,which of these requirements,at a minimum, must be satisfied?()
第17题:
Which two statements are true about the rendezvo us point (RP) in a multicast network?()
第18题:
Which two statements are true about the forwarding table?()
第19题:
Which two statements are true about the forwarding table?()
第20题:
It checks the database for intrablock corruptions.
It can detect corrupt pfiles.
It can detect corrupt spfiles.
It checks the database for interblock corruptions.
It can detect corrupt block change tracking files.
第21题:
It prevents message looping,Session Advertisement(SA)messages must be RPF checked
RPF check should be done against the route to the Rendez-vous Point of the corresponding PIM-SM domain,which originated the SA
RPF checking Session Advertisement(SA)messages will cause message looping
RPF check should be done against the route to the source S of the corresponding PIM-SM domain
第22题:
MSDP is running between anycast RPs
Anycast RP provides redundancy and load-sharing capabilities
Multicast BGP is running between anycast RPs
In anycast RP,two or more RPs are configured with the same multicast IP address on loopback interfaces
In anycast RP,two or more RPs are configured with the same unicast IP address on loopback interfaces
第23题:
Dense mode multicast requires explicit join messages from their members.
Dense mode multicast uses a push model to flood traffic throughout the network and then prunes the unwanted traffic.
Sparse mode multicast uses a pull model to send multicast traffic to where it is requested.
Sparse mode uses reverse path forwarding (RPF) to prune off redundant flows.
The primary use of sparse mode multicast is for test labs and router performance testing.
第24题:
Sparse mode multicast uses a pull model to send multicast traffic to where it is requested
Dense mode multicast uses a push model to flood traffic throughout the network and then prunes the unwanted traffic
Dense mode multicast requires explicit join messa ges from their members
Sparse mode uses reverse path forwarding (RPF) to prune off redundant flows
The primary use of sparse mode multicast is for test labs and router performance testing