多选题Which two design recommendations are most appropriate when EIGRP is the data center corerouting protocol？ （）ASummarize data center subnets.BUse passive interfaces to ensure appropriate adjacencies.CTune the EIGRP timers to enable EIGRP to achieve quick

题目
多选题
Which two design recommendations are most appropriate when EIGRP is the data center corerouting protocol？ （）
A

Summarize data center subnets.

B

Use passive interfaces to ensure appropriate adjacencies.

C

Tune the EIGRP timers to enable EIGRP to achieve quicker convergence.

D

Adjust the default bandwidth value to ensure proper bandwidth on all links.

E

Advertise a default summary route into the data center core from the aggregation layer.

相似考题

1.A network design shows that R1 has four different possible paths from itself to the Data Center subnets.Which one of the following commands is most likely to show you all the possible next - hop IP addresses for these four possible routes?（）A. show ip eigrp topologyB. show ip eigrp topology all - linksC. show ip route eigrpD. show ip route eigrp all - linksE. show ip eigrp topology all - learned

2.When troubleshooting an EIGRP connectivity problem, you notice that two connected EIGRP routers are not becoming EIGRP neighbors. A ping between the two routers was successful.What is the next thing that should be checked?（）A. Verify that the EIGRP hello and hold timers match exactly.B. Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP peer command.C. Verify that EIGRP broadcast packets are not being dropped between the two routers with the show ip EIGRP traffic command.D. Verify that EIGRP is enabled for the appropriate networks on the local and neighboring router.

3.Which of the following settings could prevent two potential EIGRP neighbors from becoming neighbors?()A. The i nterface used by one router to connect to the other router is passive in the EIGRP process.B. Duplicate EIGRP router IDs.C. Mismatched Hold Timers.D. IP addresses of 10.1.1.1/24 and 10.2.2.2/24, respectively.

4.Your network consists of a large hub － and － spoke Frame Relay network with a CIR of 56 kb／s foreach spoke. Which statement about the selection of a dynamic protocol is true?()A. EIGRP would be appropriate if LMI type ANS I is NOT used.B. EIGRP would be appropriate, because the Frame Relay spokes could be segmented into their own areas.C. EIGRP would be appropriate, because by default, queries are not propagated across the slow speed Frame Relay links.D. EIGRP would be appropriate, because you can manage how much bandwidth is consumed over the Frame Relay interface.

更多“多选题Which two design recommendations are most appropriate when EIGRP is the data center corerouting protocol？ （）ASummarize data center subnets.BUse passive interfaces to ensure appropriate adjacencies.CTune the EIGRP timers to enable EIGRP to achieve quick”相关问题

  • 第1题：

    Which two statements about the EIGRP DUAL process are correct?()

    A. An EIGRP route will go active if there are no successors or feasible successors in the EIGRP topology table.

    B. An EIGRP route will go passive if there are no successors in the EIGRP topology table.

    C. DUAL will trigger an EIGRP query process while placing the flapping routes in the holddown state.

    D. A feasible successor in the EIGRP topology table can become the successor only after all the query requests have been replied to.

    E. The stuck in active state is caused when the wait for the query replies have timed out.

    F. EIGRP queries are sent during the loading state in the EIGRP neighbor establishment process.


    参考答案：A, E

  • 第2题：

    Which two design recommendations are most appropriate when EIGRP is the data center core routing protocol?()

    A. Summarize data center subnets.

    B. Use passive interfaces to ensure appropriate adjacencies.

    C. Tune the EIGRP timers to enable EIGRP to achieve quicker convergence.

    D. Adjust the default bandwidth value to ensure proper bandwidth on all links.

    E. Advertise a default summary route into the data center core from the aggregation layer.


    参考答案：A, E

  • 第3题：

    Which two design recommendations are most appropriate when EIGRP is the data center core routing protocol?（）

    • A、Summarize data center subnets.
    • B、Use passive interfaces to ensure appropriate adjacencies.
    • C、Tune the EIGRP timers to enable EIGRP to achieve quicker convergence.
    • D、Adjust the default bandwidth value to ensure proper bandwidth on all links.
    • E、Advertise a default summary route into the data center core from the aggregation layer.

    正确答案:A,E

  • 第4题：

    What parameters must you specify when you enable EIGRP routing?（）

    • A、The broadcast address, and AS number
    • B、The network number and AS number
    • C、EIGRP routing, network number and passive interface
    • D、EIGRP routing, network number, and AS

    正确答案:D

  • 第5题：

    Which two design recommendations are most appropriate when EIGRP is the data center corerouting protocol？ （）

    • A、 Summarize data center subnets.
    • B、 Use passive interfaces to ensure appropriate adjacencies.
    • C、 Tune the EIGRP timers to enable EIGRP to achieve quicker convergence.
    • D、 Adjust the default bandwidth value to ensure proper bandwidth on all links.
    • E、 Advertise a default summary route into the data center core from the aggregation layer.

    正确答案:A,E

  • 第6题：

    Which of the following are not BGRP data structures？ （Choose all that apply.）（）

    • A、EIGRP database table
    • B、EIGRP CEF table
    • C、EIGRP neighbor table
    • D、EIGRP adjacency table
    • E、EIGRP interface table
    • F、EIGRP topology table

    正确答案:A,B,D

  • 第7题：

    A network design shows that R1 has four different possible paths from itself to the Data Center subnets. Which of the following can influence which o f those routes become feasible successor routes, assuming that you follow the Cisco recommended practice of not changing metric weights？（）

    • A、The configuration of EIGRP offset lists
    • B、Current link loads
    • C、Changing interface delay settings
    • D、Configu ration of variance

    正确答案:A,C

  • 第8题：

    多选题
    You are using IPv6， and would like to configure EIGRPv3. Which three of these correctly describe how you can perform this configuration？（）
    A

    EIGRP for IPv6 is directly configured on the interfaces over which it runs.

    B

    EIGRP for IPv6 is not configured on the interfaces over which it runs， but if a user uses passive-interface configuration， EIGRP for IPv6 needs to be configured on the interface that is made passive.

    C

    There is a network statement configuration in EIGRP for IPv6， the same as for IPv4.

    D

    There is no network statement configuration in EIGRP for IPv6.

    E

    When a user uses a passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive.

    F

    When a user uses a non-passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive


    正确答案： C,F
    解析： 暂无解析

  • 第9题：

    多选题
    Which two design recommendations are most appropriate when EIGRP is the data center corerouting protocol？ （）
    A

    Summarize data center subnets.

    B

    Use passive interfaces to ensure appropriate adjacencies.

    C

    Tune the EIGRP timers to enable EIGRP to achieve quicker convergence.

    D

    Adjust the default bandwidth value to ensure proper bandwidth on all links.

    E

    Advertise a default summary route into the data center core from the aggregation layer.


    正确答案： D,C
    解析： 暂无解析

  • 第10题：

    多选题
    Which two design recommendations are most appropriate when OSPF is the data center core routing protocol? （）
    A

    Never use passive interfaces.

    B

    Use NSSA areas from the core down.

    C

    Use totally stub areas to stop type 3 LSAs.

    D

    Use the lowest Ethernet interface IP address as the router ID.

    E

    Tune OSPF timers to enable OSPF to achieve quicker convergence.


    正确答案： A,B
    解析： 暂无解析

  • 第11题：

    多选题
    A network design shows that R1 has four different possible paths from itself to the Data Center subnets. Which of the following can influence which o f those routes become feasible successor routes, assuming that you follow the Cisco recommended practice of not changing metric weights？（）
    A

    The configuration of EIGRP offset lists

    B

    Current link loads

    C

    Changing interface delay settings

    D

    Configu ration of variance


    正确答案： D,C
    解析： 暂无解析

  • 第12题：

    单选题
    Which of the following is true regarding the effect of EIGRP queries on the network design？（）
    A

     EIGRP queries will be the most significant issue with respect to stability and convergence 

    B

     EIGRP queries are not a consideration as long as EIGRP has a feasible successor with a nexthop AD that is greater than the FD of the current successor route 

    C

     EIGRP queries will only increase the convergence time when there are no EIGRP stubsdesigned in the network


    正确答案： C
    解析： 暂无解析

  • 第13题：

    What parameters must you specify when you enable EIGRP routing?()

    A. The broadcast address, and AS number

    B. The network number and AS number

    C. EIGRP routing, network number and passive interface

    D. EIGRP routing, network number, and AS


    参考答案：D

  • 第14题：

    Which two design recommendations are most appropriate when OSPF is the data center core routing protocol? ()

    A. Never use passive interfaces.

    B. Use NSSA areas from the core down.

    C. Use totally stub areas to stop type 3 LSAs.

    D. Use the lowest Ethernet interface IP address as the router ID.

    E. Tune OSPF timers to enable OSPF to achieve quicker convergence.


    参考答案：B, E

  • 第15题：

    Which of the following is true regarding the effect of EIGRP queries on the network design？（）

    • A、 EIGRP queries will be the most significant issue with respect to stability and convergence 
    • B、 EIGRP queries are not a consideration as long as EIGRP has a feasible successor with a nexthop AD that is greater than the FD of the current successor route 
    • C、 EIGRP queries will only increase the convergence time when there are no EIGRP stubsdesigned in the network

    正确答案:C

  • 第16题：

    You are using IPv6， and would like to configure EIGRPv3. Which three of these correctly describe how you can perform this configuration？（）

    • A、EIGRP for IPv6 is directly configured on the interfaces over which it runs.
    • B、EIGRP for IPv6 is not configured on the interfaces over which it runs， but if a user uses passive-interface configuration， EIGRP for IPv6 needs to be configured on the interface that is made passive.
    • C、There is a network statement configuration in EIGRP for IPv6， the same as for IPv4.
    • D、There is no network statement configuration in EIGRP for IPv6.
    • E、When a user uses a passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive.
    • F、When a user uses a non-passive-interface configuration， EIGRP for IPv6 does not need to be configured on the interface that is made passive

    正确答案:A,D,E

  • 第17题：

    Which two design recommendations are most appropriate when OSPF is the data center core routing protocol？ （）

    • A、 Never use passive interfaces.
    • B、 Use NSSA areas from the core down.
    • C、 Use totally stub areas to stop type 3 LSAs.
    • D、 Use the lowest Ethernet interface IP address as the router ID.
    • E、 Tune OSPF timers to enable OSPF to achieve quicker convergence

    正确答案:B,E

  • 第18题：

    Which two steps below should you perform on the hub router while configuring EIGRP routing over  DMVPN （mGRE tunnel）？ （）

    • A、Set the NHRP hold time to match the EIGRP hold time
    • B、Add the enable eigrp stub command
    • C、Add the disable eigrp as-member split-horizon command
    • D、Add the disable eigrp as-member next-hop-self command

    正确答案:C,D

  • 第19题：

    A network design shows that R1 has four different possible paths from itself to the Data Center subnets. Which one of the following commands is most likely to show you all the possible next - hop IP addresses for these four possible routes?（）

    • A、show ip eigrp topology
    • B、show ip eigrp topology all - links
    • C、show ip route eigrp
    • D、show ip route eigrp all - links
    • E、show ip eigrp topology all - learned

    正确答案:B

  • 第20题：

    多选题
    Which of the following settings could prevent two potential EIGRP neighbors from becoming neighbors?（）
    A

    The i nterface used by one router to connect to the other router is passive in the EIGRP process.

    B

    Duplicate EIGRP router IDs.

    C

    Mismatched Hold Timers.

    D

    IP addresses of 10.1.1.1/24 and 10.2.2.2/24, respectively.


    正确答案： C,B
    解析： 暂无解析

  • 第21题：

    多选题
    Which two statements about the EIGRP DUAL process are correct?（）
    A

    An EIGRP route will go active if there are no successors or feasible successors in the EIGRP topology table.

    B

    An EIGRP route will go passive  if there are no successors in the EIGRP topology table.

    C

    DUAL will trigger an EIGRP query process while placing the flapping routes in the holddown state.

    D

    A feasible successor in the EIGRP topology table can become the successor only after all the query requests have been replied to.

    E

    The stuck in active state is caused when the wait for the query replies have timed out.

    F

    EIGRP queries are sent during the loading state in the EIGRP neighbor establishment process.


    正确答案： D,A
    解析： 暂无解析

  • 第22题：

    多选题
    Which two design recommendations are most appropriate when EIGRP is the data center core routing protocol?（）
    A

    Summarize data center subnets.

    B

    Use passive interfaces to ensure appropriate adjacencies.

    C

    Tune the EIGRP timers to enable EIGRP to achieve quicker convergence.

    D

    Adjust the default bandwidth value to ensure proper bandwidth on all links.

    E

    Advertise a default summary route into the data center core from the aggregation layer.


    正确答案： E,B
    解析： 暂无解析

  • 第23题：

    多选题
    Which two steps below should you perform on the hub router while configuring EIGRP routing over  DMVPN （mGRE tunnel）？ （）
    A

    Set the NHRP hold time to match the EIGRP hold time

    B

    Add the enable eigrp stub command

    C

    Add the disable eigrp as-member split-horizon command

    D

    Add the disable eigrp as-member next-hop-self command


    正确答案： C,A
    解析： 暂无解析

  • 第24题：

    单选题
    A network design shows that R1 has four different possible paths from itself to the Data Center subnets. Which one of the following commands is most likely to show you all the possible next - hop IP addresses for these four possible routes?（）
    A

    show ip eigrp topology

    B

    show ip eigrp topology all - links

    C

    show ip route eigrp

    D

    show ip route eigrp all - links

    E

    show ip eigrp topology all - learned


    正确答案： B
    解析： 暂无解析

相关内容