You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）A、The bypass-routing parameter is used to test the density on the T1 lineB、The bypass-routing parameter cannot be used on a T1 interfaceC、Th

题目

You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）

  • A、The bypass-routing parameter is used to test the density on the T1 line
  • B、The bypass-routing parameter cannot be used on a T1 interface
  • C、The bypass-routing parameter allows you to ping a host through an interface that has no route through it
  • D、The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic
相似考题

1.When troubleshooting ATM, which command would allow you to test reachability from one side of an ATM cloud to the other?()A.ping atm vci 0.100 interface at-0/1/0 end-to-endB.ping atm vci 0.100 interface at-0/1/0 circuitC.ping atm vci 0.100 interface at-0/1/0 far-endD.ping atm vci 0.100 interface at-0/1/0 final-hop

2.Refer to the exhibit. What must be done on router RTA to ensure that EIGRP works effectively in a Frame Relay multipoint environment?()A. Issue the command bandwidth 224 on the physical interface.B. Issue the command bandwidth 56 on the physical interface.C. Issue the command bandwidth 224 on each subinterface.D. Issue the command bandwidth 56 on each subinterface.

3.Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）A. All OSPF implementations must have at le ast one interface in area 0.B. You are attempting to run in the broadcast mode over an NBMA interface.C. Both routers are configured to function as a BDR; therefore, there is no DR router.D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.

4.Asystemadministratoristryingtotroubleshootcompanywideemailproblemsthatmayberelated toDNS.WhichofthefollowingnetworktoolswouldbeMOSTusefultodetermineifitisaDNS issue?()A.netstatB.tracertC.nslookupD.ping

更多“You issue the ping interface t1-”相关问题

  • 第1题：

    While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）

    A. Serial 0 is up, line protocol is up

    B. Serial 0 is up, line protocol is down

    C. Serial 0 is down, line protocol is down

    D. Serial 0 is down, line protocol is up

    E. Serial 0 is administratively down, line protocol is down

    F. Serial 0 is administratively down, line protocol is up


    参考答案：E

  • 第2题：

    When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?()

    A.show ip access-list

    B.show access-list

    C.list ip interface

    D.show interface

    E.show ip interface


    参考答案：E

  • 第3题：

    While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）

    • A、Serial 0 is up, line protocol is up
    • B、Serial 0 is up, line protocol is down
    • C、Serial 0 is down, line protocol is down
    • D、Serial 0 is down, line protocol is up
    • E、Serial 0 is administratively down, line protocol is down
    • F、Serial 0 is administratively down, line protocol is up

    正确答案:E

  • 第4题：

    You issue the ping interface t1-1/1/0 bypass-routing count 1000 rapid command. Which statement is correct?（）

    • A、The count parameter creates a counter that you can view with the show firewall command.
    • B、The count parameter allows the router to count the number of pings for logging purposes.
    • C、The count parameter allows the router to pause for 1000 seconds before sending out a ping.
    • D、The count parameter allows the router to send out 1000 pings and then stop.

    正确答案:D

  • 第5题：

    YOU issue the pins interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）

    • A、The bypass-routing parameter is used to test the density on the TI line.
    • B、The bypass-routing parameter cannot be used on a T1 interface.
    • C、The bypass-routing parameter allows you to ping a host through an interface that has no route through it.
    • D、The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic

    正确答案:C

  • 第6题：

    While troubleshooting a connectivity problem on the network, you issue the ping command from your PC command prompt, but the output shows "request times out."At which OSI layer is this problem associated with?（）

    • A、The data link layer
    • B、The application layer
    • C、The access layer
    • D、The session layer
    • E、The network layer

    正确答案:E

  • 第7题：

    When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?（）

    • A、show ip access-list
    • B、show access-list
    • C、list ip interface
    • D、show interface
    • E、show ip interface

    正确答案:E

  • 第8题：

    单选题
    While troubleshooting a connectivity issue from a PC you obtain the following information: Local PC IP address: 10.0.0.35/24 Default Gateway: 10.0.0.1 Remote Sever: 10.5.75.250/24 You then conduct the following tests from the local PC: Ping 127.0.0.1 – Successful Ping 10.0.0.35 – Successful Ping 10.0.0.1 – Unsuccessful Ping 10.5.75.250 – Unsuccessful What is the underlying cause of this problem?（）
    A

    A remote physical layer problem exists.

    B

    The host NIC is not functioning.

    C

    TCP/IP has not been correctly installed on the host.

    D

    A local physical layer problem exists.


    正确答案： D
    解析： 暂无解析

  • 第9题：

    单选题
    While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）
    A

    Serial 0 is up, line protocol is up

    B

    Serial 0 is up, line protocol is down

    C

    Serial 0 is down, line protocol is down

    D

    Serial 0 is down, line protocol is up

    E

    Serial 0 is administratively down, line protocol is down

    F

    Serial 0 is administratively down, line protocol is up


    正确答案： D
    解析： 暂无解析

  • 第10题：

    单选题
    You issue the ping interface t1-1/1/0 bypass-routing count 1000 rapid command. Which statement is correct?（）
    A

    The count parameter creates a counter that you can view with the show firewall command.

    B

    The count parameter allows the router to count the number of pings for logging purposes.

    C

    The count parameter allows the router to pause for 1000 seconds before sending out a ping.

    D

    The count parameter allows the router to send out 1000 pings and then stop.


    正确答案： B
    解析： 暂无解析

  • 第11题：

    单选题
    When you are troubleshooting an ACL issue on a router,which command can help you to verify which interfaces are affected by the ACL?（）
    A

    show ip access-list

    B

    show access-list

    C

    list ip interface

    D

    show interface

    E

    show ip interface


    正确答案： B
    解析： 暂无解析

  • 第12题：

    单选题
    You issue the ping interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）
    A

    The count parameter creates a counter that you can view with the show firewall command

    B

    The count parameter allows the router to count the number of pings for logging purposes

    C

    The count parameter allows the router to pause for 10000 seconds before sending out a ping

    D

    The count parameter allows the router to send out 1000 pings and then stop


    正确答案： A
    解析： 暂无解析

  • 第13题：

    You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?()

    A. Show interface lmi

    B. Show frame-relay lmi

    C. Show interface frame-relay

    D. Debug frame-relay interface.


    参考答案：B

  • 第14题：

    While troubleshooting a connectivity issue from a PC you obtain the following information: Local PC IP address: 10.0.0.35/24 Default Gateway: 10.0.0.1 Remote Sever: 10.5.75.250/24 You then conduct the following tests from the local PC: Ping 127.0.0.1 – Successful Ping 10.0.0.35 – Successful Ping 10.0.0.1 – Unsuccessful Ping 10.5.75.250 – Unsuccessful What is the underlying cause of this problem?（）

    • A、A remote physical layer problem exists.
    • B、The host NIC is not functioning.
    • C、TCP/IP has not been correctly installed on the host.
    • D、A local physical layer problem exists.

    正确答案:D

  • 第15题：

    You issue the ping interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）

    • A、The count parameter creates a counter that you can view with the show firewall command
    • B、The count parameter allows the router to count the number of pings for logging purposes
    • C、The count parameter allows the router to pause for 10000 seconds before sending out a ping
    • D、The count parameter allows the router to send out 1000 pings and then stop

    正确答案:D

  • 第16题：

    You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）

    • A、The bypass-routing parameter is used to test the density on the T1 line.
    • B、The bypass-routing parameter cannot be used on a T1 interface.
    • C、The bypass-routing parameter allows you to ping a host through an interface that has no route through it.
    • D、The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic.

    正确答案:C

  • 第17题：

    When troubleshooting ATM, which command would allow you to test reachability from one side of an ATM cloud to the other?（）

    • A、ping atm vci 0.100 interface at-0/1/0 end-to-end
    • B、ping atm vci 0.100 interface at-0/1/0 circuit
    • C、ping atm vci 0.100 interface at-0/1/0 far-end
    • D、ping atm vci 0.100 interface at-0/1/0 final-hop

    正确答案:A

  • 第18题：

    While troubleshooting connectivity issues, you log into a remote router. From there,you wish to see the layer 1 and layer 2 status of the interface. Which of the following IOS commands would you issue to check the current IP addressing, as well as theyer 1 and layer 2 status of an interface?（）

    • A、TK1# show version
    • B、TK1# show protocols
    • C、TK1# show interfaces
    • D、TK1# show controllers
    • E、TK1# show ip interface
    • F、TK1# show startup-config

    正确答案:C,D,E

  • 第19题：

    You want to allow all hosts on interface ge-0/0/0.0 to be able to ping the device’s ge-0/0/0.0 IP address.Where do you configure this functionality？（）

    • A、[edit interfaces]
    • B、[edit security zones]
    • C、[edit system services]
    • D、[edit security interfaces]

    正确答案:B

  • 第20题：

    单选题
    You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）
    A

    The bypass-routing parameter is used to test the density on the T1 line

    B

    The bypass-routing parameter cannot be used on a T1 interface

    C

    The bypass-routing parameter allows you to ping a host through an interface that has no route through it

    D

    The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic


    正确答案： A
    解析： 暂无解析

  • 第21题：

    单选题
    You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）
    A

    The bypass-routing parameter is used to test the density on the T1 line.

    B

    The bypass-routing parameter cannot be used on a T1 interface.

    C

    The bypass-routing parameter allows you to ping a host through an interface that has no route through it.

    D

    The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic.


    正确答案： B
    解析： 暂无解析

  • 第22题：

    单选题
    YOU issue the pins interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）
    A

    The bypass-routing parameter is used to test the density on the TI line.

    B

    The bypass-routing parameter cannot be used on a T1 interface.

    C

    The bypass-routing parameter allows you to ping a host through an interface that has no route through it.

    D

    The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic


    正确答案： D
    解析： 暂无解析

  • 第23题：

    单选题
    You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?（）
    A

    Show interface lmi

    B

    Show frame-relay lmi

    C

    Show interface frame-relay

    D

    Debug frame-relay interface.


    正确答案： B
    解析： 暂无解析

相关内容