A technician needs to add network capacity. However, when plugging a second switch into the first switch, there is no link light. Which of the following is the cause of this situation?（）A、The switches are not stackableB、The cable was not wired using 568A

题目

A technician needs to add network capacity. However, when plugging a second switch into the first switch, there is no link light. Which of the following is the cause of this situation?（）

  • A、The switches are not stackable
  • B、The cable was not wired using 568A
  • C、The cable needs to be a crossover cable
  • D、The switches have IGMP snooping enabled
相似考题

1.A network technician is installing a new managed 10/100 Mbps switch on the network. The network has an older printer with a 10Mbps network adapter that will be moved to the new switch.Which of the following settings on the switch will need to be configured to support the printer?（）A. MAC filteringB. IP addressC. PoED. Port speed

2.An administrator has a malfunctioning uninterruptible power supply (UPS). Which of the following is the MOST likely cause of the problem?()A. Battery needs to be replacedB. Light switch is turned offC. Smart cable is disconnectedD. UPS needs a firmware update

3.The Ezonexam network administrator needs to a switch named VE1 to become the root bridge for a redundant path switched network. What can be done to ensure that VE1 will always assume the role as the root bridge?A．Assign the switch a higher MAC address than the other switches in the network haveB．Establish a direct link from the switch to all other switches in the networkC．Configure the switch full-duplex operation and configure the other switches for half-duplex operationD．Configure the switch so that it has lower priority than other switches in the networkE．None of the above

4.A technician needs to manage a switch by using the management port on the back of the switch.Which of the following cables would the technician use?()A.StraightB.ConsoleC.CrossoverD.Loopback

参考答案和解析
正确答案:C
更多“A technician needs to add network capacity. However, when plugging a second switch into the first switch, there is no link light. Which of the following is the cause of this situation?（）A、The switches are not stackableB、The cable was not wired using 568AC”相关问题

  • 第1题：

    A new Catalyst switch is connected to an existing switch using a crossover cable. As a result of this, what would the switch port link lights display?()

    A. The switch port link lights will be off on both switches indicating the ports are not connected.

    B. The switch port link light will be off on one switch indicating that STP has disabled the port.

    C. The switch port link lights will flash amber indicating an error.

    D. The switch port link lights will be green indicating normal operation.


    参考答案：D

  • 第2题：

    A network administrator needs to force a high-performance switch that is located in the MDF to become the root bridge for a redundant path switched network. What can be done to ensure that this switch assumes the role as root bridge（）。

    A.Establish a direct link from the switch to all other switches in the network.

    B.Assign the switch a higher MAC address than the other switches in the network have.

    C.Configure the switch so that it has a lower priority than other switches in the network.

    D.Configure the switch for full-duplex operation and configure the other switches for half-duplex operation.

    E.Connect the switch directly to the MDF router, which will force the switch to assume the role of root bridge.


    参考答案：C

  • 第3题：

    A technician needs to manage a switch by using the management port on the back of the switch.Which of the following cables would the technician use?（）

    • A、Straight
    • B、Console
    • C、Crossover
    • D、Loopback

    正确答案:B

  • 第4题：

    A network technician is installing a new managed 10/100 Mbps switch on the network. The network has an older printer with a 10Mbps network adapter that will be moved to the new switch. Which of the following settings on the switch will need to be configured to support the printer?（）

    • A、MAC filtering
    • B、IP address
    • C、PoE
    • D、Port speed

    正确答案:D

  • 第5题：

    While troubleshooting a network connectivity problem, a technician observes steady link lights on both the workstation NIC and the switch port to which the workstation is connected. However, when the ping command is issued from the workstation, the output message "Request timed out." is displayed. At which layer of the OSI model does the problem most likely exist（）。

    • A、the session layer
    • B、the protocol layer
    • C、the data link layer
    • D、the access layer
    • E、the network layer
    • F、the application layer

    正确答案:E

  • 第6题：

    A network administrator needs to add an additional connection to a room. The administrator adds a new Ethernet switch and must connect it to an existing switch. Which cable type should be used to connect the two switches?（）

    • A、CAT3 cable
    • B、Serial cable
    • C、Crossover cable
    • D、Rollover cable

    正确答案:C

  • 第7题：

    An administrator replaces the network card in a web server. After replacing the network card some users can access the server but others cannot.  Which of the following is the FIRST thing the administrator should check？（）

    • A、 Default gateway
    • B、 The ports on the switch
    • C、 Port security on the servers switch port
    • D、 Ethernet cable

    正确答案:A

  • 第8题：

    An administrator has a malfunctioning uninterruptible power supply (UPS). Which of the following is the MOST likely cause of the problem?（）

    • A、Battery needs to be replaced
    • B、Light switch is turned off
    • C、Smart cable is disconnected
    • D、UPS needs a firmware update

    正确答案:A

  • 第9题：

    A user has just moved a PC from one office to another. The patch cable and the NIC do notappear to be functioning in the new office but were working before the move. The patch cable is plugged in correctly to both the NIC and the wall jack. Which of the following actions should the technician take FIRST?（）

    • A、Verify that the network card is compatible with the operating system.
    • B、Verify that the port on the switch is enabled.
    • C、Update the network card driver.
    • D、Replace the network cable with a crossover cable.

    正确答案:B

  • 第10题：

    单选题
    A technician needs to find an end of a network cable drop. Which of the following tools would the technician use?（）
    A

    Cable tester

    B

    Multimeter

    C

    Toner probe

    D

    Loopback plug


    正确答案： B
    解析： 暂无解析

  • 第11题：

    单选题
    A technician needs to add network capacity. However, when plugging a second switch into the first switch, there is no link light. Which of the following is the cause of this situation?（）
    A

    The switches are not stackable

    B

    The cable was not wired using 568A

    C

    The cable needs to be a crossover cable

    D

    The switches have IGMP snooping enabled


    正确答案： C
    解析： 暂无解析

  • 第12题：

    单选题
    An administrator has a malfunctioning uninterruptible power supply （UPS）. Which of the following is the MOST likely cause of the problem？（）
    A

     Battery needs to be replaced

    B

     Light switch is turned off

    C

     Smart cable is disconnected

    D

     UPS needs a firmware update


    正确答案： B
    解析： 暂无解析

  • 第13题：

    A network administrator is explaining VTP configuration to a new technician. What should the network administrator tell the new technician about VTP configuration?()

    A. A switch in the VTP client mode cannot update its local VLAN database.

    B. A trunk link must be configured between the switches to forward VTP updates.

    C. A switch in the VTP server mode can update a switch in the VTP transparent mode.

    D. A switch in the VTP transparent mode will forward updates that it receives to other switches.

    E. A switch in the VTP server mode only updates switches in the VTP client mode that have a higher VTP revision number.

    F. A switch in the VTP server mode will update switches in the VTP client mode regardless of the configured VTP domain membership.


    参考答案：A, B, D

  • 第14题：

    While troubleshooting a network connectivity problem, a technician observes steady link lights on both the workstation NIC and the switch port to which the workstation is connected. However, when the ping command is issued from the workstation, the output message "Request timed out." is displayed. At which layer of the OSI model does the problem most likely exist（）。

    A.the session layer

    B.the protocol layer

    C.the data link layer

    D.the access layer

    E.the network layer

    F.the application layer


    参考答案：E

  • 第15题：

    A new Catalyst switch is connected to an existing switch using a crossover cable. As a result of this, what would the switch port link lights display?（）

    • A、The switch port link lights will be off on both switches indicating the ports are not connected.
    • B、The switch port link light will be off on one switch indicating that STP has disabled the port.
    • C、The switch port link lights will flash amber indicating an error.
    • D、The switch port link lights will be green indicating normal operation.

    正确答案:D

  • 第16题：

    A technician is troubleshooting a laptop LCD, and when the cover is opened nothing shows on the screen. Then all of a sudden the screen comes on and works fine. Which of the following should the technician check FIRST?（）

    • A、Backlight
    • B、Inverter
    • C、Loose cable
    • D、Lid switch

    正确答案:D

  • 第17题：

    A user on a network cannot access any network resources. The link light on the computer showsthat a connection is present. Which of the following is the MOST likely cause of the problem?（）

    • A、The wrong cable type has been used.
    • B、. IDS has shut down the computer's switch port.
    • C、The port on the switch is configured incorrectly
    • D、Spanning tree protocol was implemented.

    正确答案:C

  • 第18题：

    A user is unable to connect to the network. A network technician is able to determine that there is a problem on the switch. All other users on that switch are able to connect successfully to the network. Which of the following is a probable cause？（）

    • A、Switching loop is occurring on the switch.
    • B、Wrong subnet mask on the switch.
    • C、Incorrect SNMP settings on the switch.
    • D、Port is misconfigured on the switch.

    正确答案:D

  • 第19题：

    A technician needs to find an end of a network cable drop. Which of the following tools would the technician use?（）

    • A、Cable tester
    • B、Multimeter
    • C、Toner probe
    • D、Loopback plug

    正确答案:C

  • 第20题：

    When testing a CAT5 cable, the technician notices that pin A is open. However, the cable stillworks fine. Which of the following describes how this is possible?（）

    • A、The cable was tested for 100Base-TX.
    • B、The cable is a 1000BaseT cable.
    • C、The switch uses link aggregation,
    • D、The switch was setup to use MDIX

    正确答案:A

  • 第21题：

    单选题
    A technician needs to add network capacity. However, when plugging a second switch into the first switch, there is no link light. Which of the following is the cause of this situation?（）
    A

    The switches are not stackable

    B

    The cable was not wired using 568A

    C

    The cable needs to be a crossover cable

    D

    The switches have IGMP snooping enabled


    正确答案： D
    解析： 暂无解析

  • 第22题：

    单选题
    A user on a network cannot access any network resources. The link light on the computer showsthat a connection is present. Which of the following is the MOST likely cause of the problem?（）
    A

    The wrong cable type has been used.

    B

    . IDS has shut down the computer's switch port.

    C

    The port on the switch is configured incorrectly

    D

    Spanning tree protocol was implemented.


    正确答案： C
    解析： 暂无解析

  • 第23题：

    单选题
    When testing a CAT5 cable, the technician notices that pin A is open. However, the cable stillworks fine. Which of the following describes how this is possible?（）
    A

    The cable was tested for 100Base-TX.

    B

    The cable is a 1000BaseT cable.

    C

    The switch uses link aggregation,

    D

    The switch was setup to use MDIX


    正确答案： D
    解析： 暂无解析

相关内容