In which of the following configurations should a SAS hard drive jumper be placed for single drive operation?（）A、The jumpers should be placed in the single/master position.B、There are no configuration jumpers needed on a SAS hard drive.C、The jumpers shoul

题目

In which of the following configurations should a SAS hard drive jumper be placed for single drive operation?（）

  • A、The jumpers should be placed in the single/master position.
  • B、There are no configuration jumpers needed on a SAS hard drive.
  • C、The jumpers should be placed to give the drive a SCSI ID of 1.
  • D、The jumpers should be placed in the slave position.
相似考题

1.A technician has lost a necessary jumper for a new hard drive that must be installed immediately.Which of the following is the BEST solution?()A. Use a jumper from the motherboard where the new drive is going to be installed.B. Use a jumper from a hard drive that is no longer functioning.C. Contact the manufacturer of the new hard drive and have a replacement jumper shipped immediately.D. The new hard drive must be replaced

2.A technician has lost a necessary jumper for a new hard drive that must be installed immediately.Which of the following is the BEST solution?（）A、Use a jumper from the motherboard where the new drive is going to be installed.B、Use a jumper from a hard drive that is no longer functioning.C、Contact the manufacturer of the new hard drive and have a replacement jumper shipped immediately.D、The new hard drive must be replaced

3. A server has a single failed hard drive in an array that is accessed through a hot plug backplane to ease replacement of failed drives. After replacing the drive several times， each of the replacement drives failed to power up and rebuild as the failed drive.  Which of the following is the MOST likely cause of the failures？（）A、 The backplane has failed and needs to be replaced.B、 The array must be disbanded and recreated from a backup source to recognize the replacement drive.C、 There is a conflict with the optical drive on the server.D、 The server power supply is failing and not providing enough power for all the drives.

4.A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller.Which of the following is the MOST likely cause of the problem?（）A. Both hard drives have the master jumper in place.B. One hard drive is set as master and the other slave.C. The hard drive data cable is reversed.D. Both hard drives have the cable select jumper in place.

参考答案和解析
正确答案:B
更多“In which of the following configurations should a SAS hard drive jumper be placed for single drive operation?（）A、The jumpers should be placed in the single/master position.B、There are no configuration jumpers needed on a SAS hard drive.C、The jumpers shoul”相关问题

  • 第1题：

    A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller. Which of the following is the MOST likely cause of the problem?（）

    • A、Both hard drives have the master jumper in place.
    • B、One hard drive is set as master and the other slave.
    • C、The hard drive data cable is reversed.
    • D、Both hard drives have the cable select jumper in place.

    正确答案:A

  • 第2题：

    An administrator has removed a SATA hard drive from a failed server. Which of the following adapters would MOST likely be used by the administrator to transfer files from the drive to a laptop？（）

    • A、SATA to SCSI
    • B、SATA to HBA
    • C、SATA to USB
    • D、SATA to SAS

    正确答案:C

  • 第3题：

    In which of the following locations would a technician set the LBA mode for a hard drive？（）

    • A、Jumper Settings
    • B、Disk Manager
    • C、Device Manager
    • D、System BIOS

    正确答案:D

  • 第4题：

    A user requires more storage space on their computer. After a technician installs a second IDE drive in the computer, the system will not recognize that there are any hard drives installed. Which of the following is the MOST likely cause of the problem?（）

    • A、The second hard drive has not been formatted for NTFS.
    • B、The jumpers on both drives are set to the cable select position.
    • C、The jumper on the first drive is set to master and the second is set to slave.
    • D、The jumpers on both drives are set to the master position.

    正确答案:D

  • 第5题：

    Which of the following could be used to prevent an attacker from accessing the master boot drive when attaching a hard drive to another system?（）

    • A、BIOS password
    • B、Domain membership
    • C、EFS
    • D、Bitlocker

    正确答案:D

  • 第6题：

    A user reports that their hard drive has failed and needs to be replaced. Which of the following should the technician do FIRST?（）

    • A、Run the hard disk manufacturer’s diagnostic program
    • B、Re-image the drive
    • C、Replace the hard drive and load Windows
    • D、Ask the user diagnostic questions

    正确答案:D

  • 第7题：

    An administrator adds a new SATA hard drive into a functional server and attempts to boot the server. The server will no longer boot into the operating system. The administrator checks all the connections and reboots the server. The server still will not load the operating system.  Which of the following is the MOST probable cause？（）

    • A、The BIOS is set with the wrong boot order.
    • B、The jumpers have not been set on the hard drive.
    • C、The hard drive is not compatible with the system board.
    • D、The boot.ini file needs to be modified.

    正确答案:A

  • 第8题：

    Which of the following procedures should be performed to run diagnostics in single-user mode? （）

    • A、 Run standalone diagnostics from the cd. 
    • B、 Run standalone diagnostics from the AIX tape. 
    • C、 Run maintenance mode diagnostics from the hard drive. 
    • D、 Run maintenance mode diagnostics from the diskette. 

    正确答案:A

  • 第9题：

    After removing several obsolete programs from a PC, a user is experiencing slower than usuallyprocessing times. Which of the following would be the BEST way to speed up the processing? （）

    • A、Use an external hard drive.
    • B、Defrag the hard drive.
    • C、Add more RAM to the computer.
    • D、Install a larger hard drive.

    正确答案:B

  • 第10题：

    单选题
    Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）
    A

    The new drive’s jumper is set for master.

    B

    The new drive is connected to the secondary bus as a slave drive.

    C

    Both drives’ jumpers are set for cable select.

    D

    The old drive’s jumper is set for master and the new drive is set for slave.


    正确答案： A
    解析： 暂无解析

  • 第11题：

    单选题
    A user requires more storage space on their computer. After a technician installs a second IDE drive in the computer, the system will not recognize that there are any hard drives installed. Which of the following is the MOST likely cause of the problem?（）
    A

    The second hard drive has not been formatted for NTFS.

    B

    The jumpers on both drives are set to the cable select position.

    C

    The jumper on the first drive is set to master and the second is set to slave.

    D

    The jumpers on both drives are set to the master position.


    正确答案： B
    解析： 暂无解析

  • 第12题：

    单选题
    In which of the following configurations should a SAS hard drive jumper be placed for single drive operation?（）
    A

    The jumpers should be placed in the single/master position.

    B

    There are no configuration jumpers needed on a SAS hard drive.

    C

    The jumpers should be placed to give the drive a SCSI ID of 1.

    D

    The jumpers should be placed in the slave position.


    正确答案： A
    解析： 暂无解析

  • 第13题：

    On which of the following hard drive types must Bob, a technician, change the jumper setting to match the motherboard/cabling combination?（）

    • A、SATA
    • B、eSATA
    • C、Solid state
    • D、PATA

    正确答案:D

  • 第14题：

    Which of the following should be done FIRST to a hard drive before it is disposed?（）

    • A、Partition
    • B、Physical damage
    • C、Data wipe
    • D、Format

    正确答案:C

  • 第15题：

    After installing a new SATA hard drive the technician notices the drive is hot to the touch and is giving off a slight odor. Which of the following should the technician do? （）

    • A、Install a larger fan near the hard drive to cool the system.
    • B、Clean the drive with compressed air and continue to use it.
    • C、Remove and replace the drive.
    • D、Apply more thermal compound and reseat the drive.

    正确答案:C

  • 第16题：

    Which of the following is eliminated when using SATA instead of PATA technology？（）

    • A、Jumper selection
    • B、Power connector
    • C、Data port connector
    • D、Hard drive LEDs

    正确答案:A

  • 第17题：

    Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）

    • A、The new drive’s jumper is set for master.
    • B、The new drive is connected to the secondary bus as a slave drive.
    • C、Both drives’ jumpers are set for cable select.
    • D、The old drive’s jumper is set for master and the new drive is set for slave.

    正确答案:A

  • 第18题：

    The technician is working on a system and has determined that the hard drive must be reimaged. However, the customer wants to retain all the data. Which of the following would take the LEAST amount of time to implement?（）

    • A、Create a new partition on the hard drive, copy all data to the new partition, reimage the drive, and the old data will be on the new partition and accessible.
    • B、Install a new hard drive, slave the old drive, image the new drive, and show the customer how to access their data on the old drive.
    • C、Upload the data to an external FTP server, reimage the drive, and then restore the data to the newly imaged drive.
    • D、Copy data to a USB connected hard drive, reimage the drive, and then restore the data to the newly imaged drive.

    正确答案:D

  • 第19题：

    A technician is preparing to update the BIOS on a laptop. Which of the following should thetechnician do to prevent problems during the update?（）

    • A、Remove all of the memory
    • B、Plug in the AC adapter
    • C、Remove the hard drive and optical drive
    • D、Clear the partitions on the hard drive

    正确答案:B

  • 第20题：

    Which of the following drive types can be combined in a single EXP5000 expansion unit?（）

    • A、SSD, SATA and FC only 
    • B、SSD, SAS and FDE only 
    • C、SSD, FDE, SATA and FC only 
    • D、SSD, SAS, FDE, FC and SATA

    正确答案:C

  • 第21题：

    单选题
    In which of the following configurations should a SAS hard drive jumper be placed for single drive operation？（）
    A

     The jumpers should be placed in the single/master position.

    B

     There are no configuration jumpers needed on a SAS hard drive.

    C

     The jumpers should be placed to give the drive a SCSI ID of 1.

    D

     The jumpers should be placed in the slave position.


    正确答案： B
    解析： 暂无解析

  • 第22题：

    单选题
    An administrator adds a new SATA hard drive into a functional server and attempts to boot the server. The server will no longer boot into the operating system. The administrator checks all the connections and reboots the server. The server still will not load the operating system.  Which of the following is the MOST probable cause？（）
    A

    The BIOS is set with the wrong boot order.

    B

    The jumpers have not been set on the hard drive.

    C

    The hard drive is not compatible with the system board.

    D

    The boot.ini file needs to be modified.


    正确答案： A
    解析： 暂无解析

  • 第23题：

    单选题
    Which of the following procedures should be performed to run diagnostics in single-user mode? （）
    A

     Run standalone diagnostics from the cd. 

    B

     Run standalone diagnostics from the AIX tape. 

    C

     Run maintenance mode diagnostics from the hard drive. 

    D

     Run maintenance mode diagnostics from the diskette. 


    正确答案： A
    解析： 暂无解析

相关内容