An administrator installs new IDE drives into the company server. Upon starting the machine， the BIOS does not recognize any of the drives. Which of the following is the MOST likely cause of the problem？（）A、The jumpers are not set correctly on the drives.

第1题：

A server has a single failed hard drive in an array that is accessed through a hot plug backplane to ease replacement of failed drives. After replacing the drive several times， each of the replacement drives failed to power up and rebuild as the failed drive.  Which of the following is the MOST likely cause of the failures？（）

• A、 The backplane has failed and needs to be replaced.
• B、 The array must be disbanded and recreated from a backup source to recognize the replacement drive.
• C、 There is a conflict with the optical drive on the server.
• D、 The server power supply is failing and not providing enough power for all the drives.

第2题：

A PC is powered on and begins POST. The PC takes a long time when scanning for drives. The BIOS reports no hard drive can be found but the CD-ROM is identified. The technician knows that there are two hard drives on the primary EIDE controller and a CD-ROM on the secondary EIDE controller. Which of the following is the MOST likely cause of the problem?（）

• A、Both hard drives have the master jumper in place.
• B、One hard drive is set as master and the other slave.
• C、The hard drive data cable is reversed.
• D、Both hard drives have the cable select jumper in place.

第3题：

Which of the following is the MOST likely reason that a feature is not available in a virtualized environment?（）

• A、Multiple types of network cards were used.
• B、The environment is outside of the DMZ.
• C、Hardware used is not on the HCL.
• D、Internal hard drives were used for storage instead of external hard drives.

第4题：

A user requires more storage space on their computer. After a technician installs a second IDE drive in the computer, the system will not recognize that there are any hard drives installed. Which of the following is the MOST likely cause of the problem?（）

• A、The second hard drive has not been formatted for NTFS.
• B、The jumpers on both drives are set to the cable select position.
• C、The jumper on the first drive is set to master and the second is set to slave.
• D、The jumpers on both drives are set to the master position.

第5题：

The staff is not able to access a database server.  The server has an ’Operating System not found’error and is set to boot from a fiber channel SAN. All other database servers are set to boot from the SAN and access the same switch and data as this database server. Which of the following is the MOST likely cause of the problem？（）

• A、The SAN is offline
• B、Fiber channel switch
• C、Multiple failed drives in the SAN
• D、HBA

第6题：

Bob, a technician, is adding a secondary IDE hard drive to an older system. After installation and the first boot, the drive is not showing in Disk Management. Which of the following is the MOST likely cause of the issue?（）

• A、The new drive’s jumper is set for master.
• B、The new drive is connected to the secondary bus as a slave drive.
• C、Both drives’ jumpers are set for cable select.
• D、The old drive’s jumper is set for master and the new drive is set for slave.

第7题：

There is a power outage and all servers are shut down properly by the uninterruptible power supply（UPS） software. When one of the servers starts up it displays a logical drive failed error. This server has two processors，16GB of memory， and a RAID 5 array with 10 drives.  Which of the following is the MOST likely cause？（）

• A、 A failed RAID controller
• B、 Two failed processors
• C、 Two failed sticks of memory
• D、 Two failed drives

第8题：

A technician installs a SATA controller card and moves the hard drive cable from the system board to the SATA controller. The system POSTs and the controller BIOS recognizes the hard drive but does not boot to the hard drive and start Windows. Which of the following is the MOST likely cause of the problem？（）

• A、Windows cannot be booted from a controller card.
• B、The hard drive must have Windows reinstalled because a new controller card was installed.
• C、The SATA controller card was not set as a boot device in the computer BIOS.
• D、The new controller must have the correct jumper settings for Windows mode.

第9题：

第10题：

第11题：

第12题：

第13题：

An administrator just installed a new RAID controller card into a server. The firmware is current for the controller card. When the server is powered up the administrator notices that the RAID controller card is not recognized during POST. Which of the following is the cause of the problem？（）

• A、The hard drives were not plugged into the server correctly.
• B、The controller driver is outdated and needs to be updated from the OEMs website.
• C、The firmware for the server is too old and does not support the new RAID controller card.
• D、The cable from the controller to the hard drive backplane is not connected.

第14题：

An administrator has ordered a new server and setup a dedicated RAID 1 array for the application database. While troubleshooting with performance monitoring tools， the administrator is receiving lowerread/write speeds than expected.  Which of the following would be the MOST likely cause for the lower performance？（）

• A、 The BIOS needs to be upgraded.
• B、 The administrator did not add the right amount of memory.
• C、 There is a cooling issue with the server.
• D、 The administrator did not order high enough RPM drives.

第15题：

An administrator has just installed a new NIC into the server. The system POSTs fine and the NIC is recognized by the OS， but it does not receive an IP address. Which of the following is the MOST likely cause of this？（）

• A、The NIC is not on the HCL.
• B、The driver is incorrect on the server.
• C、The patch cable has not been seated properly.
• D、The NIC is not seated properly.

第16题：

A technician wants to create a spanned volume on a set of hard drives. Which of the following tools will identify if the drives will support a spanned volume?（）

• A、System Information
• B、Disk Management
• C、Device Manager
• D、Task Manager

第17题：

A user is reporting a loud grinding sound when the machine is powered on. The machine loadsinto windows and the user does not notice any performance issues. Which of the following is the MOST likely cause of the noise?（）

• A、Powersupplyfailure
• B、BadHD
• C、Badfan
• D、FaultyCD-Rom

第18题：

An administrator adds a new SATA hard drive into a functional server and attempts to boot the server. The server will no longer boot into the operating system. The administrator checks all the connections and reboots the server. The server still will not load the operating system.  Which of the following is the MOST probable cause？（）

• A、The BIOS is set with the wrong boot order.
• B、The jumpers have not been set on the hard drive.
• C、The hard drive is not compatible with the system board.
• D、The boot.ini file needs to be modified.

第19题：

The latest SCSI adaptor card is purchased from a vendor. Drivers for the operating system cannot be obtained. The SCSI adapter card is added to an existing server. Upon booting， the operating system does not detect the card. Which of the following is the MOST likely cause of the problem？（）

• A、 The SCSI card is not seated correctly.
• B、 The termination is incorrectly set on the SCSI card.
• C、 The SCSI card is not listed on the operating system HCL （Hardware Compatibility List）.
• D、 Operating system patches were not updated before installing the card.

第20题：

第21题：

第22题：

第23题：