An administrator recently installed a known good RAID adapter.  During boot up， the administrator is able to access the RAID configuration utility； however， when the administrator checks for the card in the operating system， it does not show up.  Which of

第1题：

Which of the following BIOS settings is MOST likely to speed up the boot process when disabled?（）

• A、IDE Auto Detect
• B、BIOS Administrator Password
• C、Advanced Configuration and Power Interface
• D、Plug and Play

第2题：

An administrator has just upgraded a server from non-hot plug storage to all hot plug storage. The administrator powers up the server, during POST the RAID controller is recognized but none of the drive lights flash. Which of the following should the administrator do FIRST to troubleshoot the problem?（）

• A、Check the backplane cabling.
• B、Check the server BIOS.
• C、Update the RAID controller firmware.
• D、Install the latest hard drive firmware

第3题：

Which of the following could the system administrator use to assist in debugging boot problems after the system is up？（）

• A、SMS
• B、alog
• C、fsck
• D、bosboot

第4题：

A Windows 2003 server has the operating system installed on a software RAID mirror. After a failure of one disk in the array the server will no longer boot up. The other drive is still functioning. Which of the following should be done to correct the issue？ （）

• A、 Edit the boot.ini file.
• B、 Change to a hardware RAID solution.
• C、 Recreate the array.
• D、 Edit the active drive in the array.

第5题：

An administrator installs a new network card in a properly functioning DC. During the Windows bootup process the DC bluescreens. Which of the following is the NEXT step？（）

• A、 Press F8 and boot to Directory Services Restore Mode.
• B、 Press F8 and boot to Last Known Good Configuration.
• C、 Reboot the server again.
• D、 Press F8 and boot to Safe Mode.

第6题：

A staff member reports that they cannot access the shared folder on the network； however， other staff members are reporting that they can access the shared folder. Which of the following is the BEST way to identify the problem？（）

• A、The administrator should monitor all traffic between the staff member and the server.
• B、The administrator should reconfigure the RAID configuration to allow more space.
• C、The administrator should map a drive using the net use command.
• D、The administrator should allow the staff member to use a USB drive.

第7题：

Which of the following is an advantage of hardware RAID over software RAID？（）

• A、Hardware RAID costs less than software RAID
• B、Hardware RAID is built into the operating system’s software
• C、Hardware RAID has better performance than software RAID
• D、Hardware RAID requires no configuration and software RAID does

第8题：

A system administrator is monitoring a system that has recently shown a decrease in performance. The administrator suspects there is an overload of traffic on a single Ethernet adapter. Which of the following commands is best to identify a possible overload of the Ethernet adapter？（）

• A、ping
• B、iostat
• C、netstat
• D、ifconfig

第9题：

第10题：

第11题：

第12题：

第13题：

An administrator installs a driver,reboots the DC, and logs in to configure the NIC. Once the administrator opens the NIC properties, the server bluescreens and now will no longer boot into Windows. Which of the following is the FIRST thing the administrator should do?（）

• A、Boot into Last Known Good Configuration
• B、Reseat the NIC
• C、Boot into Safe Mode
• D、Boot into Directory Services Restore Mode

第14题：

Which of the following devices would be installed if an administrator wants to control a group of servers from a remote location？（）

• A、 VLAN
• B、 KVM
• C、 IP KVM
• D、 RAID

第15题：

An administrator just installed a new RAID controller card into a server. The firmware is current for the controller card. When the server is powered up the administrator notices that the RAID controller card is not recognized during POST. Which of the following is the cause of the problem？（）

• A、The hard drives were not plugged into the server correctly.
• B、The controller driver is outdated and needs to be updated from the OEMs website.
• C、The firmware for the server is too old and does not support the new RAID controller card.
• D、The cable from the controller to the hard drive backplane is not connected.

第16题：

A user reports they cannot access the network share folder， the users workstation is configured to use automatic IP. When the administrator checks the IP address the response returns as 169.254.0.5. Which of the following should the administrator verify？（）

• A、 That there are no DHCP relay servers
• B、 That the user account on Active Directory is not locked
• C、 That the network card driver is not installed incorrectly
• D、 The network connection is functioning

第17题：

An administrator installs a new network card in a properly functioning DC. During the Windows boot up process the DC bluescreens. Which of the following is the NEXT step?（）

• A、Press F8 and boot to Directory Services Restore Mode.
• B、Press F8 and boot to Last Known Good Configuration.
• C、Reboot the server again.
• D、Press F8 and boot to Safe Mode.

第18题：

An administrator adds a new SATA hard drive into a functional server and attempts to boot the server. The server will no longer boot into the operating system. The administrator checks all the connections and reboots the server. The server still will not load the operating system.  Which of the following is the MOST probable cause？（）

• A、The BIOS is set with the wrong boot order.
• B、The jumpers have not been set on the hard drive.
• C、The hard drive is not compatible with the system board.
• D、The boot.ini file needs to be modified.

第19题：

A System p administrator has just installed a new technology level， but "oslevel -r" does not show the expected technology level.  Which of the following commands would determine which filesets are downlevel（）

• A、lppchk
• B、instfix
• C、oslevel
• D、installp

第20题：

Prior to installing a new system, an administrator needs to provide the SAN administrators with the WWN of the fibre channel cards to allow them to allocate and zone bootable storage. Due to the lack of installed operating system, the administrator will use a bootable diagnostic CD. Which option within the diag utility will display the required information?（）

• A、Task Selection > Display Hardware Vital Product Data
• B、Advanced Diagnostic Routines > Display Resource Attributes
• C、Diagnostic Routines > Display Configuration and Resource List
• D、Task Selection > Display Multipath I/O (MPIO) Device Configuration

第21题：

第22题：

第23题：