Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure. Which two statements are true about the Hot Standby Router Protocol （HSRP）？（）A、 Load sharing with HSRP is achieved by creating multiple subinterfaces on th

题目

Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure. Which two statements are true about the Hot Standby Router Protocol （HSRP）？（）

A、 Load sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers.
B、 Routers configured for HSRP can belong to multiple groups and multiple VLANs.
C、 Load sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.
D、 All routers configured for HSRP load balancing must be configured with the same priority.
E、 Routers configured for HSRP must belong to only one group per HSRP interface.

相似考题

1.HSRP. Known as Hot Stanclby Router Protocol, is a Cisco proprietarv redundancy protocol . As an experienced network administrator, you are required to configure HSRP on a XYZ network.Which TWO of the following wii be available and shared between the routers configured with HSRP? （）(Choose two.)A. a shared single interfaceB. the ability to track serial interfacesC. UDP-based hello packetsD. the impact of flapping links if timers are too low

2.Which three statements about HSRP operation are true?()A.The virtual IP address and virtual MA+K44C address are active on the HSRP Master router.B.The HSRP default timers are a 3 second hello interval and a 10 second dead interval.C.HSRP supports only clear-text authentication.D.The HSRP virtual IP address must be on a different subnet than the routers‘ interfaces on the same LAN.E.The HSRP virtual IP address must be the same as one of the router‘s interface addresses on the LAN.F.HSRP supports up to 255 groups per interface, enabling an administrative form of load balancing.

3. You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows： R1#configure terminal R1（config）#interface fa0/0 R1（config-if）#ip address 10.10.0.5 255.255.255.0 R1（config-if）#standby 1 priority 150 R1（config-if）#standby preempt delay minimum 50 R1（config-if）#standby 1 track interface fa0/2 15 R1（config-if）#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）A、 The HSRP priority for router R1 will increase to 200.B、 Router R1 will become the standby router if the priority drops below 50.C、 The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down. D、 Router R1 will wait 50 seconds before attempting to preempt the active router.

4.Which two of the following statements are true about HSRP load sharing?() (Choose two)A. It is achieved by using more than one HSRP group.B. It is done in regards to either round robin or weight basis.C. It is used to offload the active router in a certain HSRP group.D. Single group HSRP is used to achieve more efficient link utilization.E. The return traffic is influenced by HSRP load sharing configuration.

更多“Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure. Which two statements are true about the Hot Standby Router Protocol （HSRP）？（）A、 Load sharing with HSRP is achieved by creating multiple subinterfaces on the”相关问题

第1题：

HSRP has been configured between two Company devices. Which of the following describe reasons for deploying HSRP？（）
- A、 HSRP provides redundancy and fault tolerance
- B、 HSRP allows one router to automatically assume the function of the second router if the second router fails
- C、 HSRP allows one router to automatically assume the function of the second router if the second router starts
- D、 HSRP provides redundancy and load balancing
正确答案:A,B,D
第2题：

Hot Standby Router Protocol (HSRP) is able to provide network redundancy for IP networks. Concerning HSRP load sharing, which two descriptions make sense?（）
- A、It is achieved by using more than one HSRP group.
- B、It is done in regards to either round robin or weight basis.
- C、It is used to offload the active router in a certain HSRP group.
- D、The return traffic is influenced by HSRP load sharing configuration.
- E、Single group HSRP is used to achieve more efficient link utilization.
正确答案:A,C
第3题：

Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 & R2 with HSRP. While debugging router R2 you notice veryfrequent HSRP group state transitions. What is the most likely cause of this？（）
- A、physical layer issues
- B、no spanning tree loops
- C、use of non-default HSRP timers
- D、failure to set the command standby 35 preempt
正确答案:A
第4题：

Router R1 and R2 are both configured for HSRP. Which two statements about the HSRP priorities of these two routers are true？（）
- A、 To assign the HSRP router priority in a standby group， the standby group-number priority priority-value global configuration command must be used.
- B、 The default priority of a router is zero （0）.
- C、 The no standby priority command assigns a priority of 100 to the router.
- D、 Assuming that preempting has also been configured， the router with the lowest priority in an HSRP group would become the active router.
- E、 When two routers in an HSRP standby group are configured with identical priorities， the router with the highest configured IP address will become the active router.
正确答案:C,E
第5题：

You have configured router R1 with HSRP， using the standard defaults. Which three statements are true of a default HSRP configuration？（）
- A、 The Standby hello time is 2 seconds.
- B、 Two HSRP groups are configured.
- C、 The Standby track interface priority is 10.
- D、 The Standby hold time is 10 seconds
- E、 The Standby priority is 100.
- F、 The Standby delay is 3 seconds.
正确答案:C,D,E
第6题：

For the following protocols， which one provides a mechanism to transparently intercept and redirect CIFS traffic from a client to a local Cisco Wida Area Application engine？（）
- A、Virtual Router Redundancy Protocol（VRRP）
- B、File Transport Protocol（FTP）
- C、Hot Standby Routing Protocol（HSRP）
- D、Web Cache Communication Protocol（WCCP）
正确答案:D
第7题：

多选题
Hot Standby Router Protocol (HSRP) is able to provide network redundancy for IP networks. Concerning HSRP load sharing, which two descriptions make sense?（）
A
It is achieved by using more than one HSRP group.
B
It is done in regards to either round robin or weight basis.
C
It is used to offload the active router in a certain HSRP group.
D
The return traffic is influenced by HSRP load sharing configuration.
E
Single group HSRP is used to achieve more efficient link utilization.

正确答案： E,D
解析：暂无解析
第8题：

多选题
HSRP has been configured between two Company devices. Which of the following describe reasons for deploying HSRP？（）
A
HSRP provides redundancy and fault tolerance
B
HSRP allows one router to automatically assume the function of the second router if the second router fails
C
HSRP allows one router to automatically assume the function of the second router if the second router starts
D
HSRP provides redundancy and load balancing

正确答案： C,B
解析：暂无解析
第9题：

多选题
Which three statements about HSRP operation are true?（）
A
The virtual IP address and virtual MA+K44C address are active on the HSRP Master router.
B
The HSRP default timers are a 3 second hello interval and a 10 second dead interval.
C
HSRP supports only clear-text authentication.
D
The HSRP virtual IP address must be on a different subnet than the routers' interfaces on the same LAN.
E
The HSRP virtual IP address must be the same as one of the router's interface addresses on the LAN.
F
HSRP supports up to 255 groups per interface, enabling an administrative form of load balancing.

正确答案： A,E
解析：暂无解析
第10题：

多选题
You have configured router R1 with HSRP， using the standard defaults. Which three statements are true of a default HSRP configuration？（）
A
The Standby hello time is 2 seconds.
B
Two HSRP groups are configured.
C
The Standby track interface priority is 10.
D
The Standby hold time is 10 seconds
E
The Standby priority is 100.
F
The Standby delay is 3 seconds.

正确答案： A,B
解析：暂无解析
第11题：

多选题
HSRP. Known as Hot Stanclby Router Protocol, is a Cisco proprietarv redundancy protocol . As an experienced network administrator, you are required to configure HSRP on a XYZ network. Which TWO of the following wii be available and shared between the routers configured with HSRP? （）(Choose two.)
A
a shared single interface
B
the ability to track serial interfaces
C
UDP-based hello packets
D
the impact of flapping links if timers are too low

正确答案： B,D
解析：暂无解析
第12题：

多选题
Which two of the following statements are true about HSRP load sharing?（） (Choose two)
A
It is achieved by using more than one HSRP group.
B
It is done in regards to either round robin or weight basis.
C
It is used to offload the active router in a certain HSRP group.
D
Single group HSRP is used to achieve more efficient link utilization.
E
The return traffic is influenced by HSRP load sharing configuration.

正确答案： B,A
解析：暂无解析
第13题：

Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 & R2 with HSRP. While debugging router R2 you notice very frequent HSRP group state transitions. What is the most likely cause of this？（）
- A、 physical layer issues
- B、 no spanning tree loops
- C、 use of non-default HSRP timers
- D、 failure to set the command standby 35 preempt
正确答案:A
第14题：

HSRP. Known as Hot Stanclby Router Protocol, is a Cisco proprietarv redundancy protocol . As an experienced network administrator, you are required to configure HSRP on a XYZ network. Which TWO of the following wii be available and shared between the routers configured with HSRP? （）(Choose two.)
- A、a shared single interface
- B、the ability to track serial interfaces
- C、UDP-based hello packets
- D、the impact of flapping links if timers are too low
正确答案:B,D
第15题：

Which three statements best describe HSRP configuration on Cisco Nexus switches？（）
- A、 In a vPC topology， the primary HSRP router will respond to ARP requests， but both HSRP routers will forward data traffic. No additional configuration is required.
- B、 In a vPC topology， the primary HSRP router will respond to ARP requests， but both HSRP routers will forward data traffic if the peer-gateway feature is enabled.
- C、 You can configure two overlapping HSRP groups to load share traffic from the connected hosts while providing the default router redundancy.
- D、 You can use the show standby command to verify HSRP operation and configuration.
- E、 If you remove the feature hsrp command， all relevant HSRP configuration information isalso removed.
正确答案:A,C,E
第16题：

You need to decide on the best router redundancy protocol to use in the Company network. Which two statements are true about HSRP， VRRP， and GLBP？（）
- A、 GLBP and VRRP allow for MD5 authentication， whereas HSRP does not.
- B、 HSRP allows for multiple upstream active links being simultaneously used， whereas GLBP does not.
- C、 GLBP allows for router load balancing of traffic from a network segment without the different host IP configurations required to achieve the same results with HSRP.
- D、 Unlike HSRP and VRRP， GLBP allows automatic selection and simultaneous use of multiple available gateways.
- E、 GLBP allows for router load balancing of traffic from a network segment by utilizing the creation of multiple standby groups.
正确答案:C,D
第17题：

Assume two routers on the same subnet， R1 and R2， both configured for HSRP. R1 has a priority of 120.Which of the following HSRP interface configurations will always result in the R2 becoming the primary？（）
- A、standby 1 priority 110
- B、standby 1 priority 120
- C、standby 1 priority 130
- D、standby 1 priority 110 preempt
- E、standby 1 priority 120 preempt
- F、standby 1 priority 130 preempt
正确答案:C,F
第18题：

R1 and R2 exchange HSRP between each other in the Company network. In which three HSRP states do routers send hello messages？（）
- A、 Learn
- B、 Speak
- C、 Standby
- D、 Listen
- E、 Active
- F、 Remove
正确答案:B,C,E
第19题：

多选题
Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure. Which two statements are true about the Hot Standby Router Protocol （HSRP）？（）
A
Load sharing with HSRP is achieved by creating multiple subinterfaces on the HSRP routers.
B
Routers configured for HSRP can belong to multiple groups and multiple VLANs.
C
Load sharing with HSRP is achieved by creating HSRP groups on the HSRP routers.
D
All routers configured for HSRP load balancing must be configured with the same priority.
E
Routers configured for HSRP must belong to only one group per HSRP interface.

正确答案： D,C
解析：暂无解析
第20题：

多选题
You need to decide on the best router redundancy protocol to use in the Company network. Which two statements are true about HSRP， VRRP， and GLBP？（）
A
GLBP and VRRP allow for MD5 authentication， whereas HSRP does not.
B
HSRP allows for multiple upstream active links being simultaneously used， whereas GLBP does not.
C
GLBP allows for router load balancing of traffic from a network segment without the different host IP configurations required to achieve the same results with HSRP.
D
Unlike HSRP and VRRP， GLBP allows automatic selection and simultaneous use of multiple available gateways.
E
GLBP allows for router load balancing of traffic from a network segment by utilizing the creation of multiple standby groups.

正确答案： A,D
解析：暂无解析
第21题：

单选题
Routers R1 and R2 are configured for HSRP as shown below： Router R1： interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2： interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 & R2 with HSRP. While debugging router R2 you notice veryfrequent HSRP group state transitions. What is the most likely cause of this？（）
A
physical layer issues
B
no spanning tree loops
C
use of non-default HSRP timers
D
failure to set the command standby 35 preempt

正确答案： D
解析：暂无解析
第22题：

多选题
R1 and R2 exchange HSRP between each other in the Company network. In which three HSRP states do routers send hello messages？（）
A
Learn
B
Speak
C
Standby
D
Listen
E
Active
F
Remove

正确答案： A,D
解析：暂无解析
第23题：

多选题
Router R1 is configured for HSRP. Which of the following are valid HSRP states on R1？（）
A
Init
B
Idle
C
Active
D
Standby
E
Established
F
Backup

正确答案： B,A
解析：暂无解析

Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure. Which two statements are true about the Hot Standby Router Protocol （HSRP）？ （）A、 Load sharing with HSRP is achieved by creating multiple subinterfaces on th

题目

相似考题

更多“Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure. Which two statements are true about the Hot Standby Router Protocol （HSRP）？ （）A、 Load sharing with HSRP is achieved by creating multiple subinterfaces on the”相关问题

相关内容

Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure. Which two statements are true about the Hot Standby Router Protocol （HSRP）？（）A、 Load sharing with HSRP is achieved by creating multiple subinterfaces on th

更多“Routers R1 and R2 use HSRP so that one router will back up the other should there be a failure. Which two statements are true about the Hot Standby Router Protocol （HSRP）？（）A、 Load sharing with HSRP is achieved by creating multiple subinterfaces on the”相关问题